Continental Refrigerator JB320HS Manual de usuario
Hand-hydraulic Jacking Beam
U
s
e
r Ma
n
u
a
l
JB320HS
JB326HS
325067
I
ss
1
Registered no. 965702 England Phone + 44 (0) 121 326 1234 Fax +44 (0) 121 326 1298
The
F
u
t
u
r
e
in
M
ot
i
o
n
0825006-230503
2
Fig.1
WARNINGS – Safe usage instructions
OK?
2000 kg
2600 kg
Fig.2 Fig.3
3
Fig 5
6235325
6235330
Fig.4
Fig.5
4
ASSEMBLY
Fig.6
*
*
*
*
*
Example
1
2
Fig.7 Fig.8
12 mm
3
Fig.9
5
5
7
1
1
2
4
6
±
Fig.12 Fig.13
Fig.14 Fig.15
6235330
6235325 89
Fig.10 Fig.11
6
x 4 10
Fig 6
11
Fig.16
12
Fig.17
Fig.18
13
Fig.19
7
JB320HS / JB326HS
WARNING -
SAFE USAGE INSTRUCTIONS
1. The jacking beam is only to be mounted on lifts
approved by the lift manufacturer for mounting
of jacking beams - be aware that not all lifts are
approved. Rated beam capacity must be max. 2/3 of
vehicle lift capacity.
2. Mount the jacking beam with adequate support arms
on horizontal, parallel and solid rails and secure it
against crashing before use. See g. 1-19.
3. Study, understand and follow all instructions before
installing, operating, servicing, or maintaining this
equipment.
4. Check before each lift, that the support arms are
correctly placed on rail of lift or pit edge.
5. This is a lifting device only. Do not move or transport
vehicle with jacking beam.
6. Always lower the jacking beam to the nearest safety
stop immediately - or use axle stands for support -
before working on vehicle.
7. Do not overload, for instance due to sudden external
load. Overload can cause damage or failure of jack.
8. Lift only on points as specied by automaker. During
lifting be attentive that the saddles cannot slide.
9. When lifting the complete vehicle by means of 2
jacking beams they shall be placed minimum 0,85 m
from each other. Do not exceed vehicle lift capacity.
10.Gravity of load must always be placed centrally.
When lifting by means of only one saddle always
place it in the centre of the jacking beam. Also,the 2
extension arms must only be used simultaneously.
11.The vehicle must be allowed to run freely during
lifting and lowering (without brakes and in neutral).
12.No person must remain in, on or under a vehicle
when lifted or supported only by the jacking beam.
13.The operator must observe, that the jacking beam
can be operated without any danger to himself and
others.
14.The jacking beam as well as the safety valve is not
to be altered.
15.Failure to follow these warnings may result in loss
of load, damage to jack, and/or failure resulting in
personal injury or property damage.
Assembly
See g. 1-19 on previous pages.
Use
Lifting: Pump with the handle. Lower to the nearest
safety stop by turning left handle counter clockwise.
Lowering: Lift a little to allow release of safety stop.
Turn both handles counter clockwise (release valve
to the left, release for safety stop to the right). Both
handles automatically return to neutral after releasing.
Maintenance
Maintenance and repairs must always be carried out by
qualied personnel.
Daily: Check jacking beam and supports for damage -
and the correct placement of supports.
Monthly: Lubricate all moving parts with oil.
Oil rell and check: Lift to maximum height without
load and remove ller plug (12). Correct oil-level is up to
the lowest hole.
Oil quantity: 0,6 l.
Any good hydraulic oil with viscosity ISO VG 15 can be
used.
Never use brake uid.
Safety inspection
In accordance with national regulations - yet, at least
once a year - the following parts must be checked by an
expert: Supports and support arms (security against
crashing), abnormal wear and damages, weldings and
the hydraulic system for leaks. Furthermore that all
safety labels are legible.
Possible faults and how to overcome them
1. The jacking beam cannot lift to maximum height:
Rell the oil tank. (See “Maintenance”).
2. The jacking beam cannot lift enough: Check that
release handle is on “neutral” and can move freely.
Both release 6222600 (adjusted with nut 0262700)
and release arm 6222702 (adjusted with counternuts
2 x 0201600 on the pump’s release spindle) must be
loose to allow the release valve to close tightly.
3. The jacking beam cannot lower to minimum position:
Check for damages; lubricate mechanical parts.
4. The jacking beam continues to lower after letting
go of the release handle: Ventilate the hydraulic
cylinder by screw (10).
Warning: The jacking beam is not to be loaded.
Spare parts
Replace worn or broken parts with genuine jack
manufacturer supplied parts only. All major parts may
not be provided after discontinuation of a model.
Destruction
The oil must be drained o and legally disposed of.
8
JB320HS
JB326HS
9
JB320HS JB326HS
Pos. Art. no. Art. no. Pcs. Description
62 250 00 62 365 00 Hand-hydraulic
jacking beam
1 02 003 00 02 003 00 1 Nut
2 02 004 28 02 004 28 4 Disc
3 02 010 07 02 010 07 2 Screw
4 02 204 00 02 204 00 2 Circlip
5 02 205 00 02 205 00 2 Circlip
6 02 206 00 02 206 00 6 Circlip
7 02 222 00 02 222 00 2 Circlip
8 02 318 00 02 318 00 1 Screw
9 02 350 00 02 350 00 3 Screw
10 02 418 00 02 418 00 1 Hose union
11 02 421 00 02 421 00 2 Hose clamp
12 02 470 00 02 470 00 2 Plug
13 02 543 00 02 543 00 1 Chain Link
14 02 547 00 02 547 00 1 PVC handle
15 02 556 00 02 556 00 4 Bearing
16 02 558 00 02 558 00 1 Hydraulic hose
17 02 627 00 02 627 00 1 Nut
18 02 630 00 02 630 00 7 Screw
19 02 646 00 02 646 00 4 Screw
20 02 649 00 02 649 00 3 Cover button
21 02 651 00 02 651 00 1 Cover button
22 02 705 00 02 705 00 2 Bearing
23 02 754 00 02 754 00 1 Spring
24 62 022 00 62 022 00 2 Extension, 45 mm
25 62 023 00 62 023 00 2 Extension, 90 mm
26 62 024 00 62 024 00 2 Saddle
27 62 172 00 62 172 00 2 Rubber saddle
28 62 201 00 62 201 00 1 Bottom frame
29 62 202 00 62 202 00 1 Scissor half with tank
30 62 202 07 62 202 07 2 PVC disc
31 62 203 00 62 203 00 2 Outer scissor arm
32 62 207 00 62 207 00 1 Safety stop
33 62 207 04 62 207 04 1 Distance bushing
34 62 210 00 62 210 00 2 Curve
35 62 211 00 62 211 00 2 Axle
36 62 212 00 62 212 00 1 Axle
37 62 213 00 62 213 00 1 Axle
38 62 215 00 62 215 00 1 Axle
39 62 216 00 62 216 00 4 Roller
40 62 217 00 62 217 00 2 Roller
41 62 218 00 62 218 00 2 Roller axle
42 62 219 00 62 219 00 2 Axle journal
43 62 225 00 62 225 00 1 Guide block f. release
44 62 226 00 62 226 00 1 Release
45 62 227 02 62 227 02 1 Release lever
46 62 230 00 62 230 00 1 Top beam
47 62 255 00 62 255 00 1 Control panel
48 62 260 00 62 260 00 2 Base support arm
49 90 880 47 90 880 47 1 Suction hose
50 91 204 00 91 204 00 1 Oil tube
51 91 205 00 91 205 00 1 Gland
52 91 225 00 91 225 00 1 Tipping Gear Bracket
53 91 230 00 91 230 00 1 Cylinder, cpl
54 91 238 00 91 238 00 1 Pump lever
55 91 238 04 91 238 04 1 Bearing bush
56 91 250 20 91 250 26 1 Pump, cpl
10
62 255 00
62 230 00
Pos. Art. No. Art. No. Pcs. Description
62 255 00 62 255 00 Control panel
1 02 099 00 02 099 00 6 Screw
2 02 324 00 02 324 00 2 Screw
3 02 755 00 02 755 00 2 Screw
4 62 016 00 62 016 00 2 Operating handle
5 62 221 00 62 221 00 1 Front panel
6 62 222 00 62 222 00 2 Flange bearing
7 62 223 00 62 223 00 1 Release axle
8 62 224 00 62 224 00 1 Release axle
9 62 229 00 62 229 00 1 Splice plate
10 62 256 00 62 256 00 1 Stop
11 90 624 00 90 624 00 1 Spring
JB320HS JB326HS
JB320HS JB326HS
Pos. Art. No. Art. No. Pcs. Description
62 230 00 62 230 00 Top beam
1 02 102 00 02 102 00 4 Disc
2 02 308 00 02 308 00 4 Screw
3 62 204 00 62 204 00 1 Top beam
4 62 205 00 62 205 00 2 Outer arm
5 62 206 00 62 206 00 2 Middle arm
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Jacobo de Continental Refrigerator
