Continental Fireplaces BCNV40-N Manual de usuario

W415-0814 / A / 03.17.11

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.continentalﬁreplaces.com • ask@continentalﬁre.on.ca

1.31

$10.00

CERTIFIED FOR CANADAAND UNITED STATES USINGANSI/CSA METHODS.

SAFETY INFORMATION

!WARNING

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by a

qualiﬁed installer, service agency or the supplier.

If the information in these instructions

are not followed exactly, a ﬁre or

explosion may result causing property

damage, personal injury or loss of life.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

WARNING

BCNV40-N

NATURAL GAS

BCNV40-P

PROPANE

CERTIFIED UNDER CANADIANAND AMERICAN NATIONAL STANDARDS: CSA 2.22,ANSI Z21.50 FOR VENTED GAS FIREPLACES.

W415-0814 / A / 03.17.11

NOTE: changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

2.1 DIMENSIONS 5

2.1.1 ISLAND 5

2.1.2 OPEN-END 5

2.1.3 PENINSULA 5

2.1.4 SEE-THRU 5

2.2 GENERAL INSTRUCTIONS 6

2.3 GENERAL INFORMATION 7

2.4 RATING PLATE INFORMATION 7

3.0 VENTING 8

3.1 VENTING SAFETY SWITCH 8

3.2 HIGH LIMIT SWITCH 9

3.3 VENTACTION CHECK 9

4.0 INSTALLATION 9

4.1 GAS INSTALLATION 10

5.0 FRAMING 11

5.1 MINIMUM CLEARANCE TO COMBUSTIBLES 11

5.2 PENINSULA 11

5.2.1 INSTALLATION 11

5.2.2 COUNTER TOP / BAR INSTALLATION 12

5.2.3 BRICK PANEL INSTALLATION 12

5.2.4 FACING 13

5.2.5 FINISHING 13

5.3 OPEN-END 13

5.3.1 INSTALLATION 13

5.3.2 BRICK PANEL INSTALLATION 14

5.3.3 FACING 14

5.3.4 FINISHING 14

5.4 SEE-THRU 15

5.4.1 INSTALLATION 15

5.4.2 BRICK PANEL INSTALLATION 15

5.4.3 FACING 15

5.4.4 FINISHING 16

5.5 ISLAND 16

5.5.1 INSTALLATION 16

5.5.2 BRICK PANEL INSTALLATION 16

5.5.3 FACING 17

5.5.4 FINISHING 17

5.6 MINIMUM MANTEL CLEARANCES 18

6.0 FINISHING 19

6.1 HEAT SHIELD STAND-OFF REMOVAL (SEE-THRU INSTALLATION ONLY) 19

6.2 DOOR INSTALLATION 19

6.3 END DOOR INSTALLATION 19

6.4 LOG PLACEMENT 20

6.5 CHARCOAL EMBERS 21

6.6 LOGO PLACEMENT 21

6.7 LOUVRE INSTALLATION 22

7.0 OPTIONAL BLOWER INSTALLATION 22

8.0 OPERATION 24

9.0 ADJUSTMENTS 25

9.1 PILOT BURNER ADJUSTMENT 25

9.2 VENTURI ADJUSTMENT 25

9.3 FLAME CHARACTERISTICS 26

10.0 MAINTENANCE 26

10.1 CARE OF GLASS 27

10.2 CARE OF PLATED PARTS 27

11.0 REPLACEMENTS 28

12.0 TROUBLE SHOOTING 32

13.0 WARRANTY 34

14.0 SERVICE HISTORY 35

W415-0814 / A / 03.17.11

1.0 INSTALLATION OVERVIEW

Door, see “DOOR

INSTALLATION” section.

Bricks, see “BRICK PANEL

INSTALLATION” section.

Louvres, see “LOUVRE

INSTALLATION” section.

End door, see “END

DOOR INSTALLA-

TION” section.

Vent, see “VENTING”

section.

Rating plate, see “RATING

PLATE INFORMATION”

section.

W415-0814 / A / 03.17.11

2.0 INTRODUCTION

3.16B

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR IT’S CONTROLS CAN BE

DANGEROUS AND IS PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁre or injury.

• Risk of ﬁre or asphyxiation do not operate appliance with ﬁxed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal

edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away

to avoid burns or clothing ignition. Toddlers, young children and others may be susceptible to accidental

contact burns. Aphysical barrier is recommended if there are at risk individuals in the house. To restrict

access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and

other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁc and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂoor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• This appliance is a vented gas-ﬁred appliance. Do not burn wood or other materials in this appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected

before use and at least annually by a qualiﬁed service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and

free from combustible materials, gasoline and other ﬂammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁed.

• This appliance must not be connected to a chimney ﬂue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁed service

technician to inspect the appliance and to replace any part of the control system and any gas control

which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁed service person.

• Do not strike or slam shut the appliance glass door.

• Only doors / optional fronts certiﬁed with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and

your family against Carbon Monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

W415-0814 / A / 03.17.11

2.1 DIMENSIONS

2.1.1 ISLAND

38"

32 1/2"

36" 22 1/8"

22 1/8"

21/2"

41/4"

ELECTRICAL

INLET

GAS

INLET

61/2"

38"

32 1/2"

36"

38" 22 1/8"

22 1/8"

25 1/8"

21/2"

41/4"

ELECTRICAL

INLET

GAS

INLET

61/2"

38"

32 1/2"

36"

38"

22 1/8"

ELE

TRI

INLET

22 1/8"

2.1.2 OPEN-END

2.1.3 PENINSULA

2.1.4 SEE-THRU

W415-0814 / A / 03.17.11

2.2 GENERAL INSTRUCTIONS

4.1A

THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to

conform with local codes. Installation practices vary from region to region and it is important to know the

speciﬁcs that apply to your area, for example in Massachusetts State:

• This product must be installed by a licensed plumber or gas ﬁtter when installed within the commonwealth

of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of a appliance

insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂexible connector must not be longer than 36 inches.

• A Carbon Monoxide detector is required in all rooms containing gas ﬁred appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent

sealed combustion product.

The installation must conform with local codes or, in

absence of local codes, the National Gas and Propane

Installation Code CSA B149.1 in Canada, or the National

Fuel Gas Code, ANSI Z223.1 / NFPA54 in the United

States. Suitable for mobile home installation if installed in

accordance with the current standard CAN/CSA Z240MH

Series, for gas equipped mobile homes, in Canada or

NSI Z223.1 and NFPA 54 in the United States.

s long as the required clearance to combustibles is

maintained, the most desirable and beneﬁcial location for an appliance is in the center of a building, thereby

allowing the most efﬁcient use of the heat created. The location of windows, doors and the trafﬁc ﬂow in the

room where the appliance is to be located should be considered. If possible, you should choose a location

where the vent will pass through the house without cutting a ﬂoor or roof joist.

If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood

ﬂooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.

Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must

be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian

Electrical Code in Canada or the ANSI/NFPA70 National Electrical code in the United States.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

(NFI) as NFI Gas

Specialists

www.ncertied.org

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,

WITH THE GLASS DOOR OPENED OR REMOVED.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUATE VENTILATION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE

FRONT FACE OF THE UNIT.

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT

WHEN THE APPLIANCE IS OPERATING.

FIRE RISK. EXPLOSION HAZARD.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE

TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG.

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.

USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING

COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

WARNING

W415-0814 / A / 03.17.11

When the appliance is installed at eleva-

tions above 4,500ft, and in the absence of

speciﬁc recommendations from the local

authority having jurisdiction, the certiﬁed

high altitude input rating shall be reduced

at the rate of 4% for each additional

1,000ft. Expansion / contraction noises

during heating up and cooling down cycles

are normal and to be expected.

This appliance is approved for bedroom

and bed-sitting room installations and is

suitable for mobile home installation.

NO EXTERNAL ELECTRICITY (110 VOLTS OR 24 VOLTS) IS REQUIRED FOR THE GAS SYSTEM

OPERATION.

2.3 GENERAL INFORMATION

2.4 RATING PLATE INFORMATION

BCNV40

NG LP

Altitude (FT) 0-4,500 0-4500

Max. Input (BTU/HR) 30,000 30,000

Max. Output (BTU/HR) 20,400 N/A

Efﬁciency (w/the fan on) 68% N/A

Min. Inlet Gas Supply

Pressure 4.5" Water Column 11" Water Column

Max. Inlet Gas Supply

Pressure 7" Water Column 13" Water Column

Manifold Pressure (Under

Flow Conditions) 3.5" Water Column 10" Water Column

FOR YOUR SATISFACTION, ALL BURNER ASSEMBLIES HAVE BEEN TEST-FIRED TO ASSURE THEIR

OPERATIONS AND QUALITY!

Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected.

If utilizing one of Wolf Steel's trim or surround kits, see "FRAMING" section for removal of the top extension.

NOTE: The protective wrap on plated parts is best removed when the assembly is at room temperature

but this can be improved if the assembly is warmed, using a hair dryer or similar heat source.

CERTIFIEDUNDER/HOMOLOGUESELON LES NORMES:CSA 2.22b-2009 &ANSI Z21.50b-2009, VENTEDGAS FIREPLACE/FOYER AGAZ VENTILE.

SERIALNUMBER/NO.DE SERIE: BGNV40/BCNV400

MANIFOLD PRESSURE: 3.5" WATER COLUMN

PRESSION AU COLLECTEUR: 3.5" D'UNE COLONNE D'EAU

MINIMUM SUPPLY PRESSURE: 4.5" WATERCOLUMN

PRESSION D'ALIMENTATION MINIMALE: 4.5" D'UNE COLONNE D'EAU

MAXIMUM SUPPLY PRESSURE: 7.0" WATER COLUMN

PRESSION D'ALIMENTATION MAXIMALE: 7.0" D'UNE COLONNE D'EAU

NOTFOR USEWITHSOLIDFUEL.FORUSEWITHGLASS

DOORSANDCOVERSCERTIFIEDWITHTHISUNITONLY.

MANIFOLD PRESSURE: 10" WATER COLUMN

PRESSION AU COLLECTEUR: 10" D'UNE COLONNE D'EAU

MINIMUM SUPPLY PRESSURE: 11" WATER COLUMN

PRESSION D'ALIMENTATION MINIMALE: 11" D'UNE COLONNE D'EAU

MAXIMUM SUPPLY PRESSURE: 13" WATER COLUMN

PRESSION D'ALIMENTATION MAXIMALE: 13" D'UNE COLONNE D'EAU

UNCOMBUSTIBLESOLIDENEDOITPASETREUTILISEAVECCET

APPAREIL.UTILISERAVECLESPORTESVITREESHOMOLOGUEES

ET COUVERTURES SEULEMENTAVECCETTEUNITE.

AVERTISSEMENT:N'AJOUTEZ PASACETAPPAREILAUCUNMATERIAUDEVANTENTRER

ENCONTACTAVECLES FLAMMESAUTRE QUE CELUI QUIEST FOURNIAVEC CETAPPAREILPAR

LEFABRICANT.

THEAPPLIANCE MUST BEVENTED USING "B" VENT. SEE OWNERSINSTALLATION MANUALFOR

VENTINGSPECIFICS.

L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L'EVENT "B". REFERER AU MANUEL

D'INSTALLATIONDE PROPRIETAIRE POURL'EVACUATION PRECISE.

ELECTRICALRATING/ CLASSIFICATION: 115V0.82AMP, 60HZ

OPTIONALFANKIT/ ENSEMBLEDEVENTILATEURFACULTATIF: GZ550-KT

W385-0250 / D

VENTED GAS FIREPLACE. APPROVED FOR BEDROOM, AND

BED-SITTINGROOM INSTALLATION. FOYERAGAZVENTILE.HOMOLOGUE POUR INSTALLATIONDANS UNE

CHAMBRE A COUCHER, ET UN STUDIO.

MODELBGNV40N

MODELBCNV400N ALTITUDE/ ELEVATION

INPUT/ALIMENTATION

REDUCED INPUT / ALIMENTATION REDUITE

0-4500FT(0-1370m)

30,000BTU/h

20,000BTU/h

MODELBGNV40P

MODELBCNV400P

0-4500FT(0-1370m)

30,000BTU/h

20,000BTU/h

WARNING:DO NOTADD ANYMATERIAL TOTHE APPLIANCE, WHICH WILLCOME IN

CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER

WITHTHEAPPLIANCE.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS /

DEGAGEMENTSMINIMAUXDESMATERIAUX COMBUSTIBLES:

TOP/DESSUS 0 RECESSED DEPTH / PROFONDEUR D'ENCASTRE 25 ¼"

"1TNEVE/TNEV0REHCNALP/ROOLF

SIDES/ COTES 0 "5UAETNAM/ELTNAM *

BACK/ ARRIERE 0

*MAXIMUMHORIZONTALEXTENSION / L'EXTENSIONHORIZONTALEMAXIMALE: 3".

SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS. REFERER AU MANUEL

D'INSTRUCTIONPOURDES EXTENSIONS PLUS GRANDES.

WOLF STEEL LTD.

24 Napoleon Rd. Barrie, Ontario L4M 0G8 Canada

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to

the model, venting and gas type of the appliance.

For rating plate location, see “INSTALLATION OVERVIEW” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

SAMPLE

FIREPFIREP

UMM

D'EAUD'EAU

GLG

UNN

TIT

ANIFOLDANIFOLD

RESSURE

:PRESS

0"10"

TERTER

PRESSIONPRESSIO

UAU

COLLECTEUR

:COLLECTEUR:

1010

INIMU

MMINIMUM

SUP

PSUPP

PRESSUREE

RESSION

'ALIMEN

D'AL

TIO

AXIMU

MXIMUM

SUP

PSUP

PRES

RESSIO

NPRESSION

D'ALIMEND'ALIM

UNUN

COMBUSCOMBUS

PAP

AREILARE

AAA

AZAZ

NVEN

ITI

REE

HER,

COUCHER,

TET

STST

ONON

EREDUITE

50000

TFT

(

1313

30,00

00,000

BTUBTU

20,000BTU20,000BT

ODEL

MODEL

BGNV40BGNV40

ODEL

BCNVBCN

E,E,

EDD

ETHE

UMAN

ACTURERTURER

TERIALSS

TIB

SES

NDE

URPROFON

D'EN

RD'ENCAST

EXTENSION

XTENSION

RIZ

ONHORIZON

ALEA

EXTEN

S.EXTENSIONS.

ESES

W415-0814 / A / 03.17.11

3.0 VENTING

WARNING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

3.1 VENTING SAFETY SWITCH

This thermally activated switch, located in front of

the draft hood, senses an increase in temperature

and acts as a safety shut-off, see "A". It shuts down

the gas to the main burner in the event of a severe

downdraft of air or a blocked or disconnected chimney

ﬂue. If the ﬂue is blocked or has no "draw", the safety

switch will automatically shut off the supply of gas to

the main burner within 10 minutes.

This switch must be manually reset by depressing the

plunger.

The one wire running from the vent safety switch is

attached to terminal 1 of the valve, see "B". The other

wire (laying loose in the valve control area) may be

attached to a wall switch or thermostat.

TAMPERING WITH THE SAFETY SWITCH CAN RESULT IN CARBON MONOXIDE POISONING AND

POSSIBLE DEATH.

WARNING

PLUNGER A

HI LIMIT

SWITCH

This is a vented appliance and must be connected to a chimney in accordance with the current installation

codes. In absence of local codes, install to the current CAN/CGA B149 in Canada or to the current National

Fuel Gas Code ANSI Z223.1 in the United States. This model can be common-vented.

A minimum ﬁve inch diameter (5" Ø) B-vent or class A vent is required. Aminimum 5' vent height is required.

Secure the B-vent to the exhaust collar on the appliance top with 3 screws. In cold climates, the use of a B-

vent and an insulated chase is recommended.

Under extreme vent conﬁgurations, allow several minutes (5-15) for the ﬂame to stabilize after ignition. Provide

a means for visually checking the vent connection to the appliance after the appliance is installed.

W415-0814 / A / 03.17.11

3.2 HIGH LIMIT SWITCH

VALVE

THERMOSTAT OR

WALL SWITCH

VENT SAFETY

SWITCH HIGH LIMIT

SWITCH

This thermally activated switch, located in front of

the draft hood, senses an increase in temperature

and acts as a safety shut-off (See 'A' below). It shuts

down the gas to the main burner in the unlikely event

of the appliance overheating. The HI Limit switch will

automatically reset after the appliance has cooled

down, resuming gas ﬂow to the main burner.

A test for correct venting action must be made before the installed appliance can be left with the cus-

tomer.

Follow the procedure below:

A. Close all doors and windows in the room / start exhaust fans in the home /

turn the appliance blower off (if so equipped).

B. Set controls to "high" and light the appliance.

C. Wait 5 minutes. Light a match and hold to the front of the draft hood.

Venting action is satisfactory, if smoke and ﬂames are drawn into the draft hood.

Venting action is unsatisfactory, if the smoke spills back, and the ﬂame splays out-

ward. If venting action is unsatisfactory, turn off the appliance, wait 10 minutes and

try again. If the smoke is still not drawn into the draft hood, turn the appliance off and

check for vent blockage or restriction. If necessary, consult with a qualiﬁed inspector.

The Vent Safety or Hi Limit switches must not be adjusted or disabled.

In the event that either switch or any associated parts are exchanged, only

original manufacturer's parts may be used.

3.3 VENT ACTION CHECK

4.0 INSTALLATION

WARNING

FOR SAFE AND PROPER OPERATION OF THE APPLIANCE, FOLLOW THE VENTING INSTRUCTIONS

EXACTLY.

ALL INNER EXHAUST AND OUTER INTAKE VENT PIPE JOINTS MAY BE SEALED USING EITHER RED

RTV HIGH TEMP SILICONE SEALANT W573-0002 (NOT SUPPLIED) OR BLACK HIGH TEMP MILL PAC

W573-0007 (NOT SUPPLIED) WITH THE EXCEPTION OF THE APPLIANCE EXHAUST FLUE COLLAR

WHICH MUST BE SEALED USING MILL PAC.

IF USING PIPE CLAMPS TO CONNECT VENT COMPONENTS, 3 SCREWS MUST ALSO BE USED TO

ENSURE THE CONNECTION CANNOT SLIP OFF.

DO NOT CLAMP THE FLEXIBLE VENT PIPE.

RISK OF FIRE, EXPLOSION OR ASPHYXIATION. IMPROPER SUPPORT OF THE ENTIRE VENTING

SYSTEM MAY ALLOW VENT TO SAG AND SEPARATE. USE VENT RUN SUPPORTS AND CONNECT

VENT SECTIONS PER INSTALLATION INSTRUCTIONS.

RISK OF FIRE, DO NOT ALLOW LOOSE MATERIALS OR INSULATION TO TOUCH THE VENT PIPE.

REMOVE INSULATION TO ALLOW FOR THE INSTALLATION OF THE ATTIC SHIELD AND TO

MAINTAIN CLEARANCES TO COMBUSTIBLES.

68.2A

W415-0814 / A / 03.17.11

4.1 GAS INSTALLATION

30.1A

Installation and servicing to be done by a qualiﬁed installer. Do not use open ﬂame.

.Move the appliance into position and secure.

B. If equipped with a ﬂex connector the appliance is designed to accept a 1/2” gas supply. Without the

connector it is designed to accept a 3/8” gas supply. The appliance is equipped with a manual shut off

valve to turn off the gas supply to the appliance.

C. Connect the gas supply in accordance to local codes. In the absence of local codes, install to the

current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI

Z223.1 / NFPA 54 in the United States.

D. When ﬂexing any gas line, support the gas valve so that the lines are not bent or kinked.

E. The gas line ﬂex-connector should be installed to provide sufﬁcient movement for shifting the burner

assembly on it’s side to aid with servicing components.

F. Check for gas leaks by brushing on a soap and water solution.

WARNING

RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS

SPARKS OR OPEN FLAMES.

SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT

WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE

PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT

THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND

ELECTRICAL LOCATIONS, SEE “DIMENSION” SECTION.

ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG.

VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de Continental Fireplaces

Continental Fireplaces

Continental Fireplaces BCDV36CFNTR Manual de usuario

Continental Fireplaces

Continental Fireplaces Builder CBHDPNA Manual de usuario

Continental Fireplaces

Continental Fireplaces CX36NTR-1 Manual de usuario

Continental Fireplaces

Continental Fireplaces CBL36-1 Series Manual de usuario

Continental Fireplaces

Continental Fireplaces CEFB36H-BS Manual de usuario

Continental Fireplaces

Continental Fireplaces CEFB24H Manual de usuario

Continental Fireplaces

Continental Fireplaces CWHD31N Manual de usuario

Continental Fireplaces

Continental Fireplaces CDIZC - N Manual de usuario

Continental Fireplaces

Continental Fireplaces Builder X 70 Series Manual de usuario

Continental Fireplaces

Continental Fireplaces CHD35NT Manual de usuario

Continental Fireplaces

Continental Fireplaces BCDV36CFNTR Manual de usuario

Continental Fireplaces

Continental Fireplaces CLHD45N Manual de usuario

Continental Fireplaces

Continental Fireplaces CDV34-1NT Manual de usuario

Continental Fireplaces

Continental Fireplaces CBI 360-N Guía del usuario

Continental Fireplaces

Continental Fireplaces CDI-30GN Manual de usuario

Continental Fireplaces

Continental Fireplaces CHDX40NT-1 Manual de usuario

Continental Fireplaces

Continental Fireplaces CDI-30N Manual de usuario

Continental Fireplaces

Continental Fireplaces CVFS60N Manual de usuario

Continental Fireplaces

Continental Fireplaces Builder Series Manual de usuario

Continental Fireplaces

Continental Fireplaces CDI-30N Manual de usuario

Continental Fireplaces

Continental Fireplaces BCDV42CFN Manual de usuario

Continental Fireplaces

Continental Fireplaces CVF36P Manual de usuario

Continental Fireplaces

Continental Fireplaces CVF42-1N Manual de usuario

Continental Fireplaces

Continental Fireplaces CX70NTE Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación