Contacta STS-K009-IP-L-B Manual de operación

Installation &

User Guide

September 2021

Window Intercom System

Surface Mounted Entry System - STS-K009-IP-L-B

Contents

Product Overview

Components

Connections

Installation Instructions

Speaker & Microphone Kit Installation

  AmplierInstallation

Speaker & Mic. Kit Installation

Hearing Loop Installation

 AmplierSetup

Cleaning / Maintenance

Troubleshooting

Engineer’s Mode

Contactahasapolicyofcontinuousproductdevelopment,andthereforesmallspecication

changesmaynotbereectedinthismanual.Images,labels,packaging,accessoriesandproduct

colours are subject to change without notice.

Product Overview

This speech transfer system provides high quality sound across partitions or

safety screens. It includes our surface mounted entry unit with IP-55 rating,

ouropenduplexamplier,ahearingloop,andafree-standingmicrophone

andspeakerunitforsta.

The surface mounted entry unit (K009-IP) must be installed as per installation

instructions to maintain its IP-55 rating.

1. Installation and User Manual

2. Amplier

3. Hearing Loop Sticker

4. IEC Lead

5. Power Supply

6. Hearing Loop Aerial

7. Mounting Bracket

Fixing Kit:

• Adhesive Clip x 10

• No.6 x 1/2” Countersunk Screws x15

• P-Clips x6

• M3 x 24mm Universal Wall Plugs x4

• M3 x 25mm Fixing Screws x4

General Components

Speaker & Microphone Components

1. StaMicrophone

2. Surface Mounted Entry Unit

3. Screw Sticker Covers x4

Connections

StaMicrophone

Hearing Loop

Power Supply

Surface Mounted

Entry Unit

Cable Colour Amplifier Socket Amplifier Pin #

Blue Customer speaker 3-4

Brown Customer mic 14-15

Green Call/LED 9-10

Orange LEDs 11-12

Surface Mounted Entry Unit to Amplifier - Connections Colours

Werecommendthatinstallationiscarriedoutbyaqualiedengineer,

adhering to relevant standards.

Check the contents of the box to familiarise yourself with the components.

Installation Instructions

Negative -

or screened cable

Positive +

A toolkit recommended to install the system will include:

Trim cables if necessary (excluding the power supply)

to the required length to connect to the back of the

amplier.Bareapproximately6mmofthecableendsto

connect to the 2 pin plugs.

• Pliers

• Tape Measure

• Pencil or Marker Pen

• Torch

• Cable Ties

• Electrical Insulation Tape

• Trunking

• Screwdrivers (Flat or Blade 2.5mm

and Phillips Head PH2)

• Battery or Mains Drill

• Drillbits: 2mm, 3mm, 5mm and 7mm

• Allen Key Set

• Cable Tacking Gun (10mm)

• Wire Cutters/Strippers

Recommended Tools

1. Placetheamplierunderastacounter,ensuringthatitwillnotobstruct

stawhentheyaresitting.

2. Markthefourxingpointsfortheamplierunderthecounter.

3. Drillandxtheamplierinplaceusingthesuppliedscrews.

4. Installtheamplier’spowersupplyclosetoapowersocketoutletusing

thesuppliedmountingbracketandxingscrews.

Fixing points

Amplifier Installation

AmplierInstallation

LED connection or alert tone (if required)

CondenceLEDtoconrmthesystemispowered

oranalerttonefortheattentionofsta

Stamicrophoneconnection

Customer microphone connection

CondenceLED(ifrequired)forstatusalerts

and fault detection

Hearing loop aerial

Line in connection for

external audio source

Staspeakerconnection

Customer speaker connection

Power input

connection

Use power supply

through ground

supply only

Microphone & Speaker Installation

1. Placethestamicrophoneonthestasideof

the partition, ensuring that it does not cause an

obstructionandisasclosetostaaspossible.

It is ideally positioned no more than 300mm

awayfromthestamember.

2. Usethecablemanagementholetorunthesta

microphonecablebacktotheamplier.Ifthere

Sta

microphone

is not already a cable management hole, drill in a suitable location near

the rear of the counter.

3. Find a suitable location for surface mounted entry unit (K009-IP).

It is ideally placed at head height (approximately 1.65m) from the ground

to allow most customers to easily press and speak into it. The unit should

beinstalledagainstawalloratsurfacetoensuremaximumingress

protection.

4. Remove the x4 screws that hold the front cover of the unit together and

put these to the side.

5. Carefullyremovethefrontcoverandlocatethex4xingpointholes.The

front cover should be handled with care as it will be wired to the back

box.

Fixing

points

Cable

management

hole

6. Markthex4xingpointholesandcablemanagementholeonthe

mounting surface.

7. Prepare your mounting surface by installing any wall plugs necessary into

thexingpointsmarked.

Note: This kit is provided with x4 universal surface M3 x 24mm wall plugs

whichrequirea5mmpilothole.Pleaseensureappropriatexingsare

used for your intended surface.

Ensure that cables are routed into the cable management hole prior to

securing the back box to the mounting surface.

8. Usex425mmxingscrewstosecuretheboxtoitsintendedsurface

using the holes created in the step 7.

Cable

management

hole

Cable

9. Use the x4 removed screws from step 4 to re-attach the front cover to

the back box. Ensure the seal is in place and in good condition. Tighten

accordingly.

10. Take the x4 supplied screw cover stickers and cover the visible silver

screws (highlighted in the image below).

Theaerialshouldbexedunderthedesk-toporcountercentrallyonthe

custome or visitor side, one half mounted horizontally under the counter and

theotherhalfmountedvertically,facingthecustomer/visitor(asintherst

scenario below).

Position the aerial under the counter using either the provided P-clips

oranotherxingmethodofyourchoice.Seethediagrambelowfor

recommended positioning.

A is the optimum layout for a counter hearing loop.

B and C are acceptable only if A is not possible and the layout is aligned so

thatthemagneticeldwillbedirectedtowardsuser’sheadheights.

Ensure all hearing loop signage is displayed clearly.

XX

Hearing Loop Installation

A B C

Tabla de contenidos

Otros manuales de Sistema de intercomunicación de Contacta

Contacta

Contacta STS-K071 Manual de operación

Contacta

Contacta STS-K080-IP Manual de operación

Contacta

Contacta STS-K020 Manual de operación

Contacta

Contacta STS-K060 Manual de operación

Contacta

Contacta STS-K001L Manual de operación

Contacta

Contacta IL-EL42-PB Manual de usuario

Contacta

Contacta STS-K070 Manual de operación

Contacta

Contacta STS-K035-B Manual de operación

Contacta

Contacta STS-K002L Manual de operación

Contacta

Contacta STS-K020 Manual de operación

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

CyberData

CyberData 011211 series Manual

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario