Consew 206RB-5 Manual de usuario

OIMSBW

OPERATING

INSTRUCTIONS

FOR

206RB-

CONSOLIDATED

SEWING

MACHINE

CORP.

From the library of: Superior Sewing Machine & Supply LLC

OPERATING

INSTRUCTIONS

CONSEW

Model

206RB-5

This is a guide to use

CONSEW model 206RB-5,high-speed single needle compound

walking-foot needle feed machine, under the best condition.

Please read this guide thoroughly so that you may except good performance.

NEEDLE

BAR

STROKE

HOOK

BOBBIN

STITCH

LENGTH

FEED

MECHANISM

PRESSERFOOT

PRESSERLIFT

THREAD

TAKE

BED

DIMENSION

WORKING

SPACE

MACHINE

WEIGHT

MOTOR

THREAD

OIL

USE

SISTER

MACHINES

SPECIFICATIONS

;DP

17.

Standard

Needle

#22

:33.2mm

iRotating hook, 25.7

x 11mm

rMaximum

10mm

:Drop and Needle feed with Walking foot.

With

reverse

stitch

:Alternating pressers

:8.5mm(by hand lever) / 14mm (by knee lift)

:Slide motion type.Thread take up stroke 68.5mm

:177mm

477mm

:258mm

110mm

:25.5KGS. (Head only)

:l/3

1/2HP

Clutch

motor

:S5mthetic

:White spindle oil

:Leather goods,sporting goods, interior

automobiles,vinyl goods,canvas sheet,etc.

Model 204RB Drop and needle feed fnechanism.

Model 208RB Needle feed and walking foot mechanism.

From the library of: Superior Sewing Machine & Supply LLC

-INDEX-

CONTENTS

Page

Setting up the machine 1

Breaking-in & Direction

rotation 1

Oiling 2

Needle

Thread

Winding the lower thread on the bobbin • • • • 5

Adjustment

the bobbin winder 5

Removing and inserting the bobbin 6

Threading the machine 7

Regulating the thread tensions 8

Adjusting the lift

the alternating presser feet 9

How to re-set the safety clutch mechanism 9

Extra slotted needle plate 9

INFORMATION

FOR

ADJUSTMENT

Adjusting the height

the feed dog 10

Relative position

the feeder to needle plate 10

The position

the needle and the needle hole

the feeder 11

Timing the needle with feed dog 12

Adjusting the height

the needle bar 13

Timing between the hook and the needle 14

Adjustment

bobbin case opener 14

Adjusting the height

the presser feet 15

Timing

the vibrating presser foot 16

Adjustment

the clearance between feed forked 16

connection

and

feed

fork

collar

Adjusting the thread controller

spring*

Adjustment

spring tension

safety clutch 18

Supplementary information on oiling 19

From the library of: Superior Sewing Machine & Supply LLC

SETTING UP THE

MACHINE

(

Fig.

Before

setting up the

machine

the

table,

attach

the relative partstothe

table.

(I) Stand and treadle (2) Motor (3) Oil pan (4) Hinge

(5)

Machine

head

(6)

Knee

lifter (7)V belt

(8)

Bobbin

winder

(9)

Cotton

stand

(10)

Prop

@ ®

Fig. 1

BREAKING-IN

DIRECTION

ROTATION

To assure durability and trouble-free operation, it is imperative that for the first

several weeks

operation the maximum speed is held to no more than 2000

RPM in order to allow the parts to become properly broken in.

In operation the handwheel

the machine always turns toward the operator.

To avoid tangled threads and jamming

the sewing hook, do not turn handwheel

otherwise.

SPEED

Maximum operating speed after abreak-in period is 2400 stitches per minute

depending,

course, on the type

material being sewn, its thickness and that

the seams being crossed.

From the library of: Superior Sewing Machine & Supply LLC

OILING

Do not operate the machine, even if only for testing, unless it has been properly oiled

at every spot requiring lubrication.

The arrows on the following illustration indicate these spots.

(Fig. 2

-Fig.

6 )

NOTE;

During the breaking-in period a new machine should be oiled more frequently.

CDNSEW

-r

Fig. 3

(Without Alphabet) marked for Oiling points only.

From the library of: Superior Sewing Machine & Supply LLC

Fig. 5

(Without Alphabet) marked for Oiling points only.

From the library of: Superior Sewing Machine & Supply LLC

NEEDLE CFig.7)

CONSEW206RB is set up to use standard style DPxl7. The size of the needle to

be used should be detennined by the size

the thread, which must pass freely

through the eye

the needle.

HOW

ATTACH

THE

NEEDLE

.Turn

the machine pulleyover toward you until the needle

bar0

moves up to its

highest point.

2.Loosen the needle set screw® and put the needle

®up

into the needle bar as

deeply as it will go,with the long groove

the needle faces the left.

3.Tighten the needle set screw securely.

Fig. 7

TEREAD

Cotton,synthetic or silk thread can be used according to your purpose.

* Always use left twisted thread for upper (needle) thread, but you can use either

right or left twisted thread for lower (bobbin) thread.

From the library of: Superior Sewing Machine & Supply LLC

WINDING

THE LOWER

THREAD

ON THE

BOBBIN

{Fig.8)

1.Push

a bobbinonthe bobbin winderspindle® as far as it will go.

2.Passthe thread

from

thethread standdownward through the eye® in the tension

bracket, then between and around the back

the tension

disc®.

3.Bring the thread forward toward the bobbin and wind from below in clockwise

direction

several

times

around

the

bobbin.

4.Push the lever® toward the other side so that the pulley and V belt (®Fig.l)

will engage and then start the machine.

5.The pulley will automatically be free from the belt and stopped after the bobbin is

filled

with

thread.

THE

ABOVE

OPERATION

CAN

DONE

WHILE

SEWING.

ADJUSTMENT

THE

BOBBIN

WINDER

l.IN

CASE

UNEVEN

WINDING:

the thread does not wind evenly on the bobbin, loosen the

screw®

in the tens

ion bracket and move the bracket to the right or to the left as may be required,

then tighten the

screw®.

2.W1NDING

AMOUNT

THREAD:

Adjustment

screw®

can be turned in or out to increase or to decrease the amount

thread

wound

the

bobbin.

3.WINDING

STRENGTH:

Strength

the winding can be adjusted with the nut®.

Fig.8

From the library of: Superior Sewing Machine & Supply LLC

REMOVING

AND

INSERTING

THE

BOBBIN

1.Lift the needle bar to its highest point, placethe feed dog at this side in its travel

turning the machine pulley, and open the slide plate (A, Fig.2)

2.Pass left hand under table into opening on drip pan .

With

left thumb and index

finger,

open

the

hinged

latch

( C,Fig.4).

And

pull

bobbin

case

and

bobbin

from

rotary

hook.

While

the

latch

held

open,

the

bobbin

will

retained

inthe

bobbin

case. Release

the latch and turning

the open side

the bobbin case down

ward

will cause the bobbin to drop out.

3.Hold the bobbin between the thumb and the forefinger of your right hand and pull

out a length of about 5cm of thread . Holding the bobbin case in your left hand

turn the open side up and place the threaded bobbin into it. (Fig.9)

4.With the right hand guidethe thread into the slot in the edge of the bobbin case.

Then pull the thread to the left, under the tension spring (0,Fig.9) and into the

delivery eye . In order to keep the bobbin from dropping out

the case when it is

turned with the open side down , always keep the hinged latch (C,Fig.4) at the front

the bobbin case open.

5.Take the threaded bobbin case by the latch (C,Fig.4) and place it on the center stud

the bobbin case holder. Release latch and press bobbin case on to center stud until

the

latch

catches

the

undercut

thereon

with

click

that

can

heard.

Permit

about

5cm

bobbin thread to hand down freely. Be sure to push the slide plate to the

right before starting to sew.

Fig.9

From the library of: Superior Sewing Machine & Supply LLC

THREADING THE

MACHINE

(Fig.

10)

1.Raise the needle bar to its highest point and lead the thread from the thread stand

the following order:

From

the

thread

stand

lead the

thread

from

back to

front

through

the

lower

guide

hole

in pin® on topof

the

machine

arm,

then

again

from

right

left

through

the

upper guide hole in this pin. Pass thread in weaving fashion through the three holes

inguide®, and

from

rightto left over and

between

the

tension

discs®. Now pull

thread downward and from right to left beneath and around thread controller®,

continue to pull thread upward against the pressure

the wire spring into the fork

®, inthe

thread

controller.

Guide

upward

through

the pointof controller discs®,

and thread guide®, and from right to left through the eye in take-up lever®, down

through thread guide®, again and then

through®®®

and from left to right through

the eye

th needle

®.

2.After the above threading , hold the end

thread with your left hand, and turn the

machine pulley with your right hand so that bobbin thread may be picked up by

needle thread. And put their ends

thread back through under the presser foot for

starting operation.

REMOVE

THE

WORK

Raise the needle bar to its highest

point,

lift the presser foot and draw the fabric back

and

the

left.

Cut

the

ends

the

threads

few

centimeters.

Fig.

From the library of: Superior Sewing Machine & Supply LLC

Tabla de contenidos

Otros manuales de Máquina de coser de Consew

Consew

Consew 697CVF Manual de usuario

Consew

Consew 7360R-1 Manual de usuario

Consew

Consew 199R-1A Manual de usuario

Consew

Consew 345-3 Manual de usuario

Consew

Consew 146RB-1A-1 Manual de usuario

Consew

Consew 244B Manual

Consew

Consew 28 Manual de usuario

Consew

Consew 18 Manual de uso y cuidado

Consew

Consew 3421UX5-2 Manual de usuario

Consew

Consew 210 Manual de instrucciones

Consew

Consew 206RBL-18 Manual de lista de piezas

Consew

Consew Premier 1541S-CC Manual de usuario

Consew

Consew 206RB Manual de usuario

Consew

Consew 223R-2 Manual de usuario

Consew

Consew 332R Manual de usuario

Consew

Consew SK 2R Manual

Consew

Consew 222 Manual de usuario

Consew

Consew 332 Manual de usuario

Consew

Consew 277RFS-3 Hoja de datos

Consew

Consew 333RB-3 Manual de usuario

Consew

Consew P1206RB-7 Manual técnico

Consew

Consew P1206RB Manual técnico

Consew

Consew 227r-2 Guía

Consew

Consew 522 Manual de operación

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario