Conair 20-piece HC200WXCSC Guía

Conair thanks you for choosing our brand of

hair clipper. With practice you will soon be

doingaprofessionaljobeverytimeyouusethe

unit. This is a well-engineered, high quality

product, and we know that with proper care it

will give you years of reliable service.

Thanks again for choosing Conair, the

#1 name in personal care appliances.

20-PIECE

Haircut Kit

Instructions

For Care and Use

Model HC200WXCSC

IMPORTANT

SAFETY

INSTRUCTIONS

When using electrical appliances,

especially when children are present, basic

safety precautions should always be

taken, including the following:

READ ALL INSTRUCTIONS

BEFORE USING

KEEP AWAY FROM WATER

DANGER-any appliance is electrically

live, even when the switch is off.

To reduce the risk of death or injury by

electric shock:

1. Unplug this appliance before cleaning.

2. Do not place or store appliance where it

can fall or be pulled into a tub or sink.

3. Do not use while bathing or in a shower.

4. Do not place in, or drop into water or

other liquid.

5. Do not reach for an appliance that has

fallen into water. Unplug immediately.

6. Always unplug this appliance from elec-

trical outlet immediately after using.

DO NOT REACH INTO

THE WATER

WARNING-

To reduce the risk of

burns, electric shock, fire, or injury to persons:

1. This appliance should never be left unattended when

plugged in. Do not pull, twist, or wrap line cord

around appliance.

2. Close supervision is necessary when this

appliance is used by, on, or near

children or invalids.

3. Use this appliance only for its intended purpose

as described in this manual. Do not use

attachments not recommended by the

manufacturer. Do not use an

extension cord to operate this appliance.

4. Never operate this appliance if it has a

damaged cord or plug, or if it is not working properly,

if it has been dropped or

damaged, or dropped into water. Return the appliance

to a service center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening

on this appliance.

7. Do not place appliance on any surface while it is

operating.

8. Do not use this appliance with a

damaged or broken comb or with teeth

missing from the blades as injury may occur. Before

use, make certain blades are aligned properly.

(See “Care of your Clippers”)

9. Do not use outdoors or operate where aerosol

(spray) products are being used or where oxygen is

being administered.

10. Never operate the appliance with the air openings

blocks or while on a soft surface, such as

a bed or couch, where the air

openings may be blocked. Keep the air

openings free of lint, hair, and the like.

11. Always attach plug to appliance first, then to

outlet. To disconnect, turn all controls to “OFF” then

remove plug from outlet.

12. Avoid skin contact with moving blades.

13. When using the appliance with its cord, be

mindful of tangles or kinks in the cord. If the cord

does become tangled during use, turn the unit off and

straighten cord before operating again.

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

This appliance is intended for household

use. Use on Alternating Current 120V

AC/60Hz only. This appliance has a

polarized plug (one blade is wider than the

other). As a safety feature, this plug will fit

in the outlet only one way. If the plug does

not fit fully in the outlet, reverse the plug. If

it still does not fit, contact a qualified

electrician to install the proper outlet. Do

not attempt to defeat this safety feature.

Your new Conair®haircut kit has everything

you need to achieve professional haircuts at

home. It features a powerful clipper with

adjustable taper control and high carbon

steel blades for cutting precision. Also

included are 9 attachment combs for

different hair lengths (including left and

right ear combs), barber scissors, a styling

comb with angled teeth, a barber comb

with straight teeth, a full length barber

cape, a hard case for easy storage and 2

styling clips to assist you in cutting longer

hair styles. It also comes with lubricating oil,

a cleaning brush and a blade guard for easy

maintenance of the clipper blades.

THE CONAIR GUIDE

TO CUTTING HAIR AT HOME

Before you start:

1. Inspect your clipper. Make sure it’s free of

hair and dirt, properly oiled, and running

smoothly.

2. Place a towel around the neck of the person.

3. Seat the person so that their head is at

your eye level.This gives you greater

visibility and control.

4. First, comb hair until it’s tangle-free. Then

hold clipper in a comfortable grip. Now

you’re ready to cut.

MEDIUM TO LONG CUT

To begin with, cut only a small amount of hair

until you become used to the length each

attachment leaves the hair. Try the longest

attachment on the clipper first. If you want a

shorter cut, you can then use shorter combs.

• Short attachment comb (number 1) cuts

hair to 1/8”.

• Medium-Short attachment comb (number

2) cuts hair to 1/4”.

• Medium-Long attachment comb (number

3) cuts hair to 3/8”.

• Long attachment comb (number 4) cuts

hair to 1/2”.

• Long attachment comb (number 5) cuts

hair to 5/8”.

• Long attachment comb (number 6) cuts

hair to 3/4”.

• Long attachment comb (number 7) cuts

hair to 7/8”.

• Left ear attachment comb lightly tapers

over left ear.

• Right ear attachment comb lightly tapers

over right ear.

Attach combs by

holding them teeth

up then snapping

onto the bottom of

the clipper blade.

To remove comb

attachments place

index finger and

thumb as illustrated;

then pull out and

up.

NOTE: Never push or shove the clipper

through the hair to make it move

more quickly. Professional experience

shows that the clipper works most

efficiently when it cuts through the

hair at its own speed.

To begin cutting hair:

1. The hair should be combed in its natural

direction.

2. Using the largest attachment comb, trim

sides from the bottom upwards. Hold

clipperlightly against the hair with teethof

the attachment comb

pointing upward, yet

flat against the head.

Gradually lift the

clipper upwards and

outward through the

hair, trimming just a

little at a time.

Repeat around sides

and back of head.

If you want hair to be

even shorter:

A) Apply more

pressure to the head

with the attachment

comb that is in place.

This takes a little

practice of course.

B) Just switch to a

shorter attachment

comb.

Remember, it’s better

to leave too much

hair than too little.

For longer hair on

top, use the barber

comb and lift hair on

the top of the head,

cutting over the

comb. Or hold the

hair between the

fingers and cut to desired length. Always

working from the front to the back of the

head, gradually cut the hair shorter by

reducing the space between the comb or

fingers and the head. Comb often to check for

uneven strands, and to get rid of trimmed

hair.

OUTLINING:

Outlining requires no attachments. Comb

hair into the desired style. Position the

clipper between the sideburns and the ear

(see below), making sure the corner edge

of the blade is against the hairline. With the

outline of the hair as your guide,

slowly move the clipper over, around and

behind the ears. For the back of the neck

and the sideburns, hold the clipper upside

down (see above) and, holding it against

the skin at the length desired, move the

clipper downward.

STOP. COMB. CHECK.

For best results, do as the professionals

do: comb hair often, and check clipping

results as you comb. This way you avoid

uneven sides, bangs, neckline, etc.

SHORT CUTS TO PERFECT

FLAT TOPS, CREW CUTS, ETC.

Always cut from the back of the neck to the

crown, using the longest comb setting.

Hold the comb attachment flat against the

head and slowly move the clipper up

through the hair. Use the same technique

for the sides, cutting from the bottom to

the upper side of the head.

For the front to the crown, cut the hair

against the direction in which it grows.

Then even it up with the sides.

For a flat top, use the flat comb, not the

attachment comb. Just cut hair on top of

the head over it (see above).

To taper hair down to the neckline, use

attachment comb #1. Comb hair and

check for uneven spots. Outline sideburns

and neck areas (see “Outlining”).

USER-MAINTENANCE

INSTRUCTIONS

CARE OF YOUR CLIPPERS

IF YOU DETERMINE THAT BLADE

ALIGNMENT IS INCORRECT:

MAINTENANCE OF THE BLADE

Always apply oil to the blades before, during

and after use. This will ensure maximum

cutting performance. Hold clipper away from

your body in a downward position and apply oil

on the front and sides of the cutter blade. Wipe

excess oil off with a soft dry cloth.

Conair®hair clippers are carefully inspected to

insure that the blades are in perfect alignment.

You will need to realign the blades after

removing them for cleaning or replacement, or

if they should be knocked out of alignment. How

can you tell if the blades need realigning?

Simply match them up, point for point, to

confirm with the drawing below.

To replace cutting comb and cutter after

removal for cleaning, replacement or, because

they are out of alignment, slide the cutter back

on to the black plastic oscillating head. Next,

you must make sure that the cutter (small

blade) and the cutting comb (large blade) are

properly aligned. Line up the new or existing

cutting comb with the two screw holes. Place

the original screws, one in each hole, and

lightly tighten with a Phillips head screwdriver.

*The top edge of the cutting comb should be

1/32” to 1/16” (.79 mm. to 1.59 mm.) higher

than the top edge of the cutter. This is important

so that the clipper does not cut too close, or

come in contact with the skin.

Tabla de contenidos

Otros manuales de Rasuradora eléctrica de Conair

Conair

Conair MT140RBC Manual de usuario

Conair

Conair TravelSmart TSLT3C Manual

Conair

Conair GMT180WRNCSC Manual de usuario

Conair

Conair inFiniti NE158CS Manual de usuario

Conair

Conair GMT235CSV Manual de usuario

Conair

Conair LTGS20RCSC Manual de usuario

Conair

Conair LT3CSC Manual de usuario

Conair

Conair MN160SP Manual de usuario

Conair

Conair i-stubble GMT900RC Manual de usuario

Conair

Conair MN160WCHCSC Manual de usuario

Conair

Conair GMT8CS Manual de usuario

Conair

Conair GMT170QCS Manual de usuario

Conair

Conair MN253WCSC Manual de usuario

Conair

Conair HC221 Guía

Conair

Conair 30 PIECE HC340WC Guía

Conair

Conair LWD400RCSC Manual de usuario

Conair

Conair Gold/Linez GMT170ECS Guía

Conair

Conair GMT183WCSC Manual de usuario

Conair

Conair GMT900 Manual de usuario

Conair

Conair HC9010GBC Manual de usuario

Conair

Conair 17 PIECE HC117WCSC Guía

Conair

Conair GMT183WCSC Manual de usuario

Conair

Conair GMT235WGBC Manual de usuario

Conair

Conair lumilisse G200 Series Manual de usuario

Manuales populares de Rasuradora eléctrica de otras marcas

Philips

Philips MicroAction 4402LC Manual de usuario

Philips

Philips HQ7740 Manual de usuario

Philips

Philips Norelco BG2022 Bodygroom Manual de usuario

Norelco

Norelco Quadra 7610X Manual de usuario

Philips

Philips 7616X Manual de usuario

Philips

Philips HQ802 Manual de usuario

Philips

Philips HQ7363/17 Manual de usuario

Braun

Braun WaterFlex WF2s Manual de usuario

Philips

Philips NORELCO S7371 Manual de usuario

Daga

Daga MT-400 Manual

Philips

Philips RQ119x Manual de usuario

Remington

Remington BHT100 Manual de usuario

Philips

Philips Bodygroom BG2000 Manual de usuario

Kompernass

Kompernass KH 5537 Manual de usuario

Remington

Remington BHT6100 Manual de usuario

Philips

Philips qc5365 Manual de usuario

MIA

MIA Aqua Body Manual de usuario

Philips

Philips NORELCO AT880 Manual de usuario