COMSOL UIR-120 Manual de usuario
USER MANUAL
USB INFRARED ADAPTER
UIR-120
USB Infrared Adapter User Manual Page 1
CONTENT
1. Introduction----------------------------------------------------------------------------------2
2. Application & Connection-------------------------------------------------------------2
3. Package Content--------------------------------------------------------------------------2
4. Product Features--------------------------------------------------------------------------2
5. System Requirements-------------------------------------------------------------------3
6. Driver Installation-------------------------------------------------------------------------3
6.1 Windows®98 Driver Installation---------------------------------------------------3
6.2 Windows®ME Driver Installation--------------------------------------------------5
6.3 Windows®2000 Driver Installation------------------------------------------------7
6.4 Windows®XP Driver Installation---------------------------------------------------9
7. Disclaimer-----------------------------------------------------------------------------------12
8. FCC Statement----------------------------------------------------------------------------12
USB Infrared Adapter User Manual Page 2
1. Introduction
Comsol USB Infrared Adapter enables IrDA wireless data communication through a
standard USB port. Powered from USB bus, this product does not require any
external power adapter. It supports SIR (2.4Kbps to 115.2Kbps), MIR (576Kbps to
1152Kbps), and FIR (4Mbps) modes. The effective data transmission distance is
from 0 to 1M. The reception or viewing angle in a typical environment is 30o (+ / - 15o).
Use the product; you could transfer data with wireless connection for PC, PDA,
digital camera, scanner and printer.
2. Application & Connection
Wireless data transfer between desktop PC and notebook PC, PDA, Digital Camera,
Scanner and Printer
Files Sharing, Photo transfer, Printing, Data Exchange and Synchronization
3. Package Content
Hardware
Comsol USB Infrared Adapter
USB Cable (A/M-A/F)
Software
Software driver on CD
4. Product Features
Easily enables IrDA function on the desktop PC through USB port
USB Plug and Play convenience
Fully compatible with IrDA 1.1 and USB 1.1 specification
Compatible with FIR 4Mbps, MIR, SIR and ASK 56Kbps
No power adapter required
Low power consumption
5. System Requirements
IBM PC 486DX4-100 MHz or higher or compatible system
Available USB port
CD-ROM drive
Windows®98, Windows®ME, Windows®2000, Windows®XP.
6. Driver Installation
USB Infrared Adapter User Manual Page 3
NOTICE: Before you install the driver on your computer, please do not connect
the Comsol USB Infrared Adapter to your computer.
6.1 Windows®98 Driver Installation
Follow the steps below to install the driver for Comsol USB Infrared Adapter:
6.1.1 Power on the computers that you will use to connect the Comsol USB
Infrared Adapter and make sure the USB port is enabled and working
properly.
6.1.2 Put the driver CD into the CD-ROM and run the D:\ Infrared UIR-
120\Drivers\WINDOWS\SETUP.EXE.
6.1.3 The dialog box will appear as below, click “NEXT” to continue.
6.1.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINDOWS\USB-IrDA).
6.1.5 The InstallShield Wizard will install the driver on your system.
6.1.6 When the dialog box appears as below, plug the Comsol USB Infrared
Adapter into the USB port.
USB Infrared Adapter User Manual Page 4
6.1.7 Windows will auto detect the new device and install the needed driver
onto your system. Click “Finish” to complete the installation.
6.1.8 When the dialog box appears as below, restart your system.
6.1.9 After windows restarts, you must check “My Computer”-“Control
Panel”-“System”-“Device Manager”, “Infrared Communication
Device” will appear and “USB-IrDA Adapter” under the Network
Adapter, “Virtual Infrared COM Port” and “Virtual Infrared LPT
Port” under the Ports (COM & LPT) item.
USB Infrared Adapter User Manual Page 5
6.2 Windows®ME Driver Installation
Follow the steps below to install the driver for Comsol USB Infrared Adapter:
6.2.1 Power on the computers that you will use to connect the Comsol USB
Infrared Adapter and make sure the USB port is enabled and working
properly.
6.2.2 Put the driver CD into the CD-ROM and run the D:\ Infrared UIR-
120\Drivers\WINDOWS\SETUP.EXE.
6.2.3 The dialog box will appear as below, click “NEXT” to continue.
6.2.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINDOWS\USB-IrDA).
6.2.5 The InstallShield Wizard will then install the driver on your system.
6.2.6 When the dialog box appears as below, plug the Comsol USB Infrared
Adapter into the USB port.
USB Infrared Adapter User Manual Page 6
6.2.7 Windows will auto detect the new device and install the needed driver
onto your system. Click “Finish” to complete the installation.
6.2.8 When the dialog box appears as below, restart your system.
6.2.9 After windows restarts, you must check “My Computer”-“Control
Panel”-“System”-“Device Manager”, “Infrared Communication
Device” will appear and “USB-IrDA Adapter” under the Network
Adapter, “Virtual Infrared COM Port” and “Virtual Infrared LPT
Port” under the Ports (COM & LPT) item.
USB Infrared Adapter User Manual Page 7
6.3 Windows®2000 Driver Installation
Follow the steps below to install the driver for Comsol USB Infrared Adapter:
6.3.1 Power on the computers that you will use to connect the Comsol USB
Infrared Adapter and make sure the USB port is enabled and working
properly.
6.3.2 Put the driver CD into the CD-ROM and run the D:\ Infrared UIR-
120\Drivers\WINDOWS\SETUP.EXE.
6.3.3 The dialog box will appear as below, click “NEXT” to continue.
6.3.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINNT\USB-IrDA), then click “NEXT” to continue.
6.3.5 The InstallShield Wizard will then install the driver on your system.
6.3.6 When the dialog box appears as below, plug the USB-IrDA Adapter into
the USB port. Windows will auto detect the new device and install the
needed driver onto your system. After all step finished, click “Finish” to
complete the installation step.
USB Infrared Adapter User Manual Page 8
6.3.7 After install the driver, you must check “My Computer”-“Control
Panel”-“System”-“Hardware”-“Device Manager”, you will see“USB-
IrDA Adapter” under the Infrared devices.
USB Infrared Adapter User Manual Page 9
6.4 Windows®XP Driver Installation
Follow the steps below to install the driver for USB to IrDA Adapter USB cable:
6.4.1 Power on the computers that you will connect the USB to IrDA Adapter
and make sure the USB port is enabled and working properly.
6.4.2 Put the driver CD into the CD-ROM and run the D:\ Infrared UIR-
120\Drivers\WINDOWS\SETUP.EXE.
6.4.3 When the dialog box appears as below, click “NEXT” to continue.
6.4.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINXP\USB-IrDA), click “NEXT” to continue.
6.4.5 The InstallShield Wizard will then install the driver on your system.
6.4.6 When the dialog box appears as below, Click “Continue Anyway” to
install the driver on your computer.
Tabla de contenidos
Otros manuales de Adaptador de COMSOL
