Compuprint 9000 Series Manual de usuario

Maintenance Manu 9050-9065-9070plus-9080-9300-10300

Rev. 1 Firmware Downloading 1

Firmware Downloading

The Compuprint 9000 and 10000 family firmware (code) resides in flash memory. Throughout the printer's life cycle firmware changes

may be made to address issues discovered in the lab, or by customers in the field. Normally it's not necessary to upgrade your printer,

but if needed upgrading your printer's firmware is easy to do.

The Base and Interface code can be installed through either the printer's Parallel or Ethernet ports in a one file download operation.

Loading code though the Parallel Port

Follow these instructions to load code through the parallel port using any computer with DOS or DOS Windows®.

The instructions assume that you are nearby the printer and can access the operator panel.

1. For Windows computers install a 'Generic/Text Only' print driver.

In Windows click Start > Control Panel > Printer and Faxes > Add printer and choose the following settings.

Local printer attached to this computer

Port = LPT1

Manufacturer = Generic

Printer = Generic / Text Only

Name your printer >Generic /Text Only

Default printer = Yes

Printer Sharing > Do not share

Test Page > No

2. Printout the printer configuration menus to ensure original settings can be restored at the end of this procedure. Label the printouts

“old”.

Note: Loading new code does not change any of the printer's network interface settings (IP, subnet mask, gateway

addresses), but other user defined configuration settings can be reset to factory default values.

Maintenance Manu 9050-9065-9070plus-9080-9300-10300

Rev. 1 Firmware Downloading 2

a. Power on the printer.

b. Load forms in the front tractor.

c. Press the ON LINE key to put the printer in WAIT status.

d. Press the PROGRAM key to enter in the Program Setup, the displays wll show: Printout ? NO

e. Press the MACRO →key, the display will show: Printout ? YES and the Programs Setup is printed.

f. After the printout, the display will show: Printout ? NO.

g. Press the LOAD/FF ↓key until CONFIG. MENU NO is displayed

h. Press the MACRO →key, the display will show: CONFIG. MENU ? YES.

i. Press the LOAD/FF ↓key until Printout ? NO is displayed

j. Press the MACRO →key, the display will show: Printout ? YES and the Configuration Setup is printed.

k. After the printout, the display will show: Printout ? NO.

l. c. Press the PROGRAM key to exit the setup phase.

3. Power off the printer.

4. Connect a standard parallel cable between your computer's LPT1 port and the printer.

5. Press and hold the printer MACRO and LF keys and power on the printer.

6. Release the keys after RELEASE KEYS displays and WAITING CODE will display with all LEDs flashing.

7. In a DOS window type: copy drive:\directory\filename.bin lpt1: /b <enter>

For example: copy c:\temp\9065_rel1.img lpt1 /b

8. While the printer code is being received RECEIVING CODE displays.

9. While the printer code is being updated ERASING SECT.XX followed by WRITING SECT.XX displays.

10. After the code download completes and is verified, CODE OK displays before the printer automatically

reboots and STARTING UP displays.

Note: If "NVM CHANGE" displays, this means that all of the printer configuration settings have been restored to factory defaults.

11. Printout the printer configuration menus again (as described above) and label them “new”.

12. Compare the old and new configuration printouts and restore the printer's configuration as needed.

Maintenance Manu 9050-9065-9070plus-9080-9300-10300

Rev. 1 Firmware Downloading 3

Loading code though the Ethernet Port

Follow these instructions to FTP printer code to a network attached printer. The instructions assume that you are nearby the printer and

can access the operator panel.

1. Printout the printer configuration menus to ensure original settings can be restored at the end of this procedure. Label this set of

configurations as old.

Note: Loading new code does not change any of the printer's network interface settings (IP, subnet mask, gateway addresses), but other

user defined configuration settings can be reset to factory default values.

a. Power on the printer.

b. Load forms in the front tractor.

c. Press the ON LINE key to put the printer in WAIT status.

d. Press the PROGRAM key to enter in the Program Setup, the displays wll show: Printout ? NO

e. Press the MACRO →key, the display will show: Printout ? YES and the Programs Setup is printed.

f. After the printout, the display will show: Printout ? NO.

g. Press the LOAD/FF ↓key until CONFIG. MENU NO is displayed

h. Press the MACRO →key, the display will show: CONFIG. MENU ? YES.

i. Press the LOAD/FF ↓key until Printout ? NO is displayed

j. Press the MACRO →key, the display will show: Printout ? YES and the Configuration Setup is printed.

k. After the printout, the display will show: Printout ? NO.

l. c. Press the PROGRAM key to exit the setup phase.

2. Make sure the code file is in the same directory that you will launch the FTP service from.

3. In Windows:

a. Click Start > Control Panel > Network and Internet Connections.

b. Click “Network Connections”.

c. Double click “Local Area Connections”.

d. Highlight “Internet Protocol (TCP/IP)”.

e. Click “Properties”.

f. Set “Subnet Mask” and “Default Gateway” to the values on the printer Configuration Setup Printout.

g. Set “IP Address” to the printer's address + 1.

Maintenance Manu 9050-9065-9070plus-9080-9300-10300

Rev. 1 Firmware Downloading 4

Example: If printer IP is 10.0.252.233 then set the computer IP to 10.0.252.234.

h. Click OK and close the window.

4. Connect your computer to the printer with an Ethernet cross-over cable.

5. Verify that the printer can be contacted from your computer.

In a DOS window, type “ping xxx.xxx.xxx.xxx” <enter> where “xxx.xxx.xxx.xxx” is the printer's IP address.

6. Open the FTP connection to the printer.

In a DOS window type ftp xxx.xxx.xxx.xxx <enter> where xxx.xxx.xxx.xxx is the printer IP address.

7. Type root for user login <enter>.

Type password (default=root) for password <enter>.

Type the commands: ha <enter> bin <enter> cd firmware <enter>.

8. Start the file transfer by typing: put filename.bin where filename.img is the name of the code file and press enter.

For example: put 9065_rel1.img <enter>.

9. While the printer code is being received, the printer will display REMOTE CONTROL for approximately 1 minute.

10. When the file is successfully transferred the following host message appears:

Enter Quit/Bye command to write CODE.

11. Close the FTP connection by typing the command: bye <enter>. After the FTP session is closed the file

update will start.

12. After the code update completes, the printer automatically reboots and STARTING UP displays.

13. Printout the printer configuration menus again and label them “new”. Compare the new printout to one the old

printout, and restore the old menu settings as needed.

Note: The new code version level also prints out.

Maintenance Manu 9050-9065-9070plus-9080-9300-10300

Rev. 1 Firmware Downloading 5

Error messages

INVALID CODE: Binary code file is corrupt or incompatible.

ERROR RECOVERY ACTION: Open the Windows (Generic/Text only) print driver queue, cancel all pending print documents, and try

again. If the error repeats the code file may be corrupted or incompatible with this printer model.

After displaying this message, the printer automatically discharges any code upgrade and escapes from the firmware downloading

procedure returning in normal ON LINE status.

FILE NOT FOUND: Code file cannot be found by DOS.

ERROR RECOVERY ACTION: Change the path in the DOS window to the directory where the code file is located.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora de Compuprint

Compuprint

Compuprint 4247-X03Plus Manual de usuario

Compuprint

Compuprint 6314 Manual de usuario

Compuprint

Compuprint 9300 Manual de usuario

Compuprint

Compuprint 10300 Manual de usuario

Compuprint

Compuprint MDP40B Manual de usuario

Compuprint

Compuprint 9060 Manual de usuario

Compuprint

Compuprint 9090 Manual de usuario

Compuprint

Compuprint 9065 Manual de usuario

Compuprint

Compuprint 9058 Manual de usuario

Compuprint

Compuprint 10200 Manual de usuario

Compuprint

Compuprint SP40 Manual de usuario

Compuprint

Compuprint 2056 Manual de usuario

Compuprint

Compuprint 4051 Manual de usuario

Compuprint

Compuprint Z03 Manual de usuario

Compuprint

Compuprint 9065plus Manual de usuario

Compuprint

Compuprint SP40 Manual de usuario

Compuprint

Compuprint 4051 plus Manual de usuario

Compuprint

Compuprint PageMaster 402N Manual de usuario

Compuprint

Compuprint PageMaster 1600c Manual de usuario

Compuprint

Compuprint 6314 Manual de usuario

Compuprint

Compuprint 9060 Manual de usuario

Compuprint

Compuprint 6414 Manual de usuario

Compuprint

Compuprint 10200 Manual de usuario

Compuprint

Compuprint 10300 Manual de operación y mantenimiento

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario