Compliance West HT-2000 Manual de usuario

Fast Charge Option

(IEC 335)

MegaPulse Surge Testers

Instruction Manual

COMPLIANCE

WESTUSA

Dear Customer:

Congratulations! Compliance West USA thanks you for

purchasing the Fast Charge option for our MegaPulse family of

surge testers. Connection of this option will allow the MegaPulse

to charge within the minimum time constraints as dictated by

relevant Standards pertaining to the MegaPulse you have

purchased.

In order to use this option safely, we urge you to carefully review

this manual before connection to your MegaPulse tester. Both

line voltage and high voltage secondary circuits could be

contacted if this option is improperly connected, and contact with

either of these circuits pose the risk of serious injury or death.

Compliance West USA stands by your instrument with a full one-

year warranty and free lifetime technical support. If the need

arises, please don't hesitate to call on us.

Thank you for your trust and confidence.

Rev. 1.0 May 12, 2005 i

Table of Contents

MegaPulse Fast Charge Option (IEC 335).................................................................................................1

General Information.....................................................................................................................1

Description.................................................................................................................................................3

Installation..................................................................................................................................................7

Testing for Proper Operation .......................................................................................................7

Removal of the Fast Charge Option.............................................................................................7

Technical Assistance..................................................................................................................................9

Table of Figures

Figure 1 Fast Charge Option (IEC 335) Front Panel...................................................................................... 4

Figure 2 MegaPulse Fast Charge Option Connector...................................................................................... 5

Figure 3 MegaPulse Option Connector Cover ............................................................................................... 6

Table of Tables

Table 1 Fast Charge Option (IEC 335) Front Panel....................................................................................... 4

Table 2 MegaPulse Fast Charge Option Connector ....................................................................................... 5

iii

Section 1

MegaPulse Fast Charge Option (IEC 335)

General Information

The MegaPulse Fast Charge Option allows the host MegaPulse tester to charge quickly enough to

satisfy minimum repetition times for tests within particular Standards. In this case, IEC 335 requires

multiple surges to be applied to the EUT with a minimum pause time of 3 seconds between pulses, and the

Fast Charge Option designed to allow recharging to the full capabilities of the tester within that time.

There are no adjustments or controls on the Fast Charge Option (IEC 335). If the option is

connected to the MegaPulse tester, the Fast Charge Option is operational.

Operation of the MegaPulse is the same whether the Fast Charge Option (IEC 335) is connected

or disconnected. Set the voltage knob for the voltage desired, press Charge, then press Trigger. See the

MegaPulse Tester manual for more information on its operation.

Connection of the Fast Charge Option (IEC 335) is simple and straightforward, but for operator

safety during installation, the Installation Instructions in Section 3 must be followed. It is imperative that

ALL connections between the Fast Charge Option (IEC 335) and the MegaPulse tester be made, and the

Connection Cover secured, before the MegaPulse is connected to line voltage. If the Fast Charge Option

(IEC 335) is disconnected, please disconnect the MegaPulse from line voltage first.

Once connected, the Fast Charge Option does not pose the risk of shock. However, both line

voltage and high voltage secondary circuits exist in the connections between the two enclosures. Exercise

care with these wires and inspect them for damage periodically.

This manual contains a general description of the option (above), installation and removal

instructions, and support information. For further information regarding operation of the MegaPulse

Tester, please see the MegaPulse Tester Manual.

Section 2

Description

The Fast Charge Option (IEC 335) contains an

auxiliary AC power supply which allows the

MegaPulse it is connected to to charge within 3

seconds as required for the minimum rest time

between repetitive cycles.

MegaPulse operation is identical whether the

Fast Charge Option (IEC 335) is connected or

not. Charge times to 12kV are approximately 12

seconds without the Option, and approximately

2-1/2 seconds with the Option installed.

Connection points on the Fast Charge Option

(IEC 335) front panel are noted in Figure 1 and

Table 1. All cables are supplied with the

Option, and cable use is also documented in

Table 1.

MegaPulse testers are supplied with a covered

connection terminal enclosure on its rear panel.

A photo of this enclosure and connection points

on the MegaPulse rear panel are noted in Figure

2 and Table 2.

After connection or disconnection of the Fast

Charge Option (IEC 335), the Connector Cover

on the rear panel of the MegaPulse must be

replaced using the four provided screws before

the MegaPulse is energized. Fig. 3 shows the

cover correctly installed.

Figure 1 Fast Charge Option (IEC 335) Front Panel

ITEM NAME FUNCTION AND CONNECTION MEANS

1 Low Voltage Connection A Line Voltage A connection from MegaPulse: Separate BLACK lead

2 Low Voltage Connection B Line Voltage B connection from MegaPulse: Separate RED lead

3 Ground Lug Ground Connection point (from MegaPulse ground): Green wire terminated in closed loop connectors

4 High Voltage Connection 1 High Voltage connection 1 to MegaPulse: Pigtail from Fast Charge Option (IEC 335)

5 High Voltage Connection 2 High Voltage connection 2 to MegaPulse: Pigtail from Fast Charge Option (IEC 335)

Table 1 Fast Charge Option (IEC 335) Front Panel

Figure 2 MegaPulse Fast Charge Option Connector

ITEM NAME FUNCTION AND CONNECTION MEANS

1 High Voltage Connection 1 High Voltage 1 connection from Option: Pigtail 1 from Option

2 High Voltage Connection 2 High Voltage 2 connection from Option: Pigtail 2 from Option

3 GROUND Grounding connection point: Connect green wire from Option ground here

4 Low Voltage Connection A Line Voltage A connection: Use separate BLACK lead

5 Low Voltage Connection B Line Voltage B connection: Use separate RED lead

Table 2 MegaPulse Fast Charge Option Connector

Figure 3 MegaPulse Option Connector Cover

Tabla de contenidos

Otros manuales de Equipo de prueba de Compliance West

Compliance West

Compliance West HT-3000 Manual de usuario

Compliance West

Compliance West GFM-40ac Manual de usuario

Compliance West

Compliance West HT-2800 Manual de usuario

Compliance West

Compliance West HT-2000P Manual de usuario

Compliance West

Compliance West GFM-300A-DM Manual de usuario

Compliance West

Compliance West HTT-1 Manual de usuario

Compliance West

Compliance West HT-S Series Manual de usuario

Compliance West

Compliance West HT-3000P-1A-AC Manual de usuario

Compliance West

Compliance West HT-2000PR Manual de usuario

Compliance West

Compliance West HT-3000P Manual de usuario

Compliance West

Compliance West HT-10KVDC Manual de usuario

Compliance West

Compliance West CDT-240 Manual de uso y cuidado

Compliance West

Compliance West MegaPulse 968-B Metallic A Manual de usuario

Compliance West

Compliance West GFM-200A Manual de usuario

Compliance West

Compliance West CDT-240 Manual de usuario

Compliance West

Compliance West MegaPulse Defib-5PF-002 Manual de usuario

Compliance West

Compliance West MegaPulse Antenna Surge PF 65 Manual de usuario

Compliance West

Compliance West MegaPulse 1.2x50/8x20-2PF-HR Manual de usuario

Compliance West

Compliance West MegaPulse 360 Manual de usuario

Compliance West

Compliance West HT-20KVPac Manual de usuario

Compliance West

Compliance West MegaPulse Manual de usuario

Compliance West

Compliance West MegaPulse D5-PF Manual de usuario

Compliance West

Compliance West MegaPulse Capacitor A PF Series Manual de usuario

Compliance West

Compliance West GF-30AC-T Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario