Compaq 179740-001 - ProLiant - 3000 Guía de referencia rápida

White Paper

November 1999

11DT-119A-WWEN

Prepared by Storage Products

Division

Compaq Computer Corporation

Contents

Rapid Recovery with Hot-

Plug Drives.................................3

Guidelines when hot-

plugging a drive ........................3

Guidelines when Insight

Manager indicates that a

drive is degraded and should

be replaced...............................4

Conclusion .................................6

Hot-Plug Disk Drive Removal

and Replacement Guidelines for

Compaq Smart Array

Controllers

Abstract: The purpose of this paper is to communicate to customers

the guidelines for implementing hot-plug removal and replacement

of hard drives when using Compaq Smart Array Controllers.

Compaq is fully committed to providing the ideal client/server high

availability solution for customers. High availability features in

Compaq Smart Array Controllers include hot-pluggable hard drives.

With hot-pluggable hard drives, customers can remove and replace

one or several drives within a server while the system is online for

rapid recovery while minimizing interruption of the network.

In order to maximize high availability, Compaq has issued customer

guidelines on extending and implementing the removal and

replacement of hot-pluggable hard drives.

Hot-Plug Disk Drive Removal and Replacement Guidelines for Compaq Smart Array Controllers 2

11DT-119A-WWEN

Notice

The information in this publication is subject to change without notice and is provided “AS IS” WITHOUT

WARRANTY OF ANY KIND. THE ENTIRE RISK ARISING OUT OF THE USE OF THIS

INFORMATION REMAINS WITH RECIPIENT. IN NO EVENT SHALL COMPAQ BE LIABLE FOR

ANY DIRECT, CONSEQUENTIAL, INCIDENTAL, SPECIAL, PUNITIVE OR OTHER DAMAGES

WHATSOEVER (INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS

PROFITS, BUSINESS INTERRUPTION OR LOSS OF BUSINESS INFORMATION), EVEN IF

COMPAQ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

The limited warranties for Compaq products are exclusively set forth in the documentation accompanying

such products. Nothing herein should be construed as constituting a further or additional warranty.

This publication does not constitute an endorsement of the product or products that were tested. The

configuration or configurations tested or described may or may not be the only available solution. This test

is not a determination or product quality or correctness, nor does it ensure compliance with any federal

state or local requirements.

Product names mentioned herein may be trademarks and/or registered trademarks of their respective

companies.

Compaq, Contura, Deskpro, Fastart, Compaq Insight Manager, LTE, PageMarq, Systempro, Systempro/LT,

ProLiant, TwinTray, ROMPaq, LicensePaq, QVision, SLT, ProLinea, SmartStart, NetFlex, DirectPlus,

QuickFind, RemotePaq, BackPaq, TechPaq, SpeedPaq, QuickBack, PaqFax, Presario, SilentCool,

CompaqCare (design), Aero, SmartStation, MiniStation, and PaqRap, registered United States Patent and

Trademark Office.

Netelligent, Armada, Cruiser, Concerto, QuickChoice, ProSignia, Systempro/XL, Net1, LTE Elite,

Vocalyst, PageMate, SoftPaq, FirstPaq, SolutionPaq, EasyPoint, EZ Help, MaxLight, MultiLock,

QuickBlank, QuickLock, UltraView, Innovate logo, Wonder Tools logo in black/white and color, and

Compaq PC Card Solution logo are trademarks and/or service marks of Compaq Computer Corporation.

Microsoft, Windows, Windows NT, Windows NT Server and Workstation, Microsoft SQL Server for

Windows NT are trademarks and/or registered trademarks of Microsoft Corporation.

NetWare and Novell are registered trademarks and intraNetWare, NDS, and Novell Directory Services are

trademarks of Novell, Inc.

Pentium is a registered trademark of Intel Corporation.

Hot-Plug Disk Drive Removal and Replacement Guidelines for Compaq Smart Array Controllers

White Paper prepared by Storage Products Division

First Edition (November 1999)

Document Number 11DT-119A-WWEN

Hot-Plug Disk Drive Removal and Replacement Guidelines for Compaq Smart Array Controllers 3

11DT-119A-WWEN

Rapid Recovery with Hot-Plug Drives1

Compaq is the clear leader in high availability rapid recovery solutions. With Compaq Pre-

Failure Warranty, system administrators can proactively schedule downtime for maintenance and

not interrupt critical business operations that rely on these enterprise servers. In addition, with

hot-pluggable drives attached to Compaq Smart Array controllers, customers can remove and

replace one or several drives within a server while the system is online, which minimizes the

interruption of the network. To ensure maximum availability, however, Compaq recommends

that customers follow the guidelines listed below in removing and replacing hot-plug drives in

Smart Array controllers:

For customers who are utilizing Compaq Smart Array Controllers:2

Note: User intervention is required if customers are not utilizing an intelligent array controller

Definitions:

Drive Array – A drive array is a physical grouping of up to 56 physical drives (members) per

array.

Logical drive – A logical drive is all of or a portion of an array with RAID 0, 1 (and derivative

0+1), 4, and 5 striping all drives of an array.

Fault tolerant RAID – All logical drives in an array must be configured with some sort of fault

tolerant RAID (1, 0+1, 4, or 5). Hot-plugging a member of an array with any logical drive

configured for RAID 0 will result in the loss of data on that logical drive.

Hot-Plugging –Hot-Plugging a disk drive is defined as physically removing a disk drive from the

storage enclosure while powered up and online.

Guidelines when hot-plugging a drive

Customers should be able to hot-plug a drive during normal activity. It should be understood,

however, that hot-plugging a disk drive will affect system performance and fault tolerance.

IMPORTANT: It is therefore recommended that disk drive replacement be performed during low activity

periods whenever possible. In addition, a current valid backup should be available of the logical drives in

the array of the drive being replaced, even if drive replacement is being made during server downtime.

When a disk drive is hot-plugged, although the system is functionally operational, the disk

subsystem may no longer be fault tolerant. Fault tolerance will be lost until the removed drive is

subsequently replaced and the rebuild operation is completed. (This will take several hours even

if the system is not busy while the rebuild is in progress). If another drive in the array should

incur an error during the period when fault tolerance is unavailable, it is possible to cause a fatal

system error due to a data error. If another drive fails during this period, the entire contents of the

array will be lost.

1Certain restrictions and exclusions apply. Requires that servers use Compaq Insight Manager in order to implement Pre-Failure

alerting.

2CAUTION: Not following these recommended guidelines can result in data loss.

Hot-Plug Disk Drive Removal and Replacement Guidelines for Compaq Smart Array Controllers 4

11DT-119A-WWEN

Note: Therefore, Compaq recommends that disk drive replacement should be performed during low

activity periods whenever possible. In addition, a current valid backup should be available of the logical

drives in the array of the drive being replaced, even if drive replacement is being made during server

downtime.

Guidelines when Insight Manager indicates that a drive

is degraded and should be replaced

EXAMPLE: Using one hot-plug replacement example, a system administrator for a large

business uses Compaq Smart Array Controllers on his servers. Compaq Insight Manager has

indicated that a drive is degraded and should be replaced under the Pre-Failure Warranty. The

system administrator should follow the guidelines outlined below for maximum availability on

his server:

•All physical drives in the affected array should be present and have the online LED Indicators

illuminated before removing the degraded hot-plug drive. If any online LED Indicators are

flashing (indicating a rebuild) or not illuminated, the degraded drive should not be hot-

plugged.

For step-by-step instructions on hot-plugging your hard drive, refer to the ProLiant Setup and

Installation Guide.

•If fault-tolerance is currently being used to recover from errors from other drives in the array

(such as media errors or signal-integrity errors), loss of fault-tolerance following a drive

removal may result in unrecoverable errors being reported to the host operating system or

failure of the entire array. To verify that such errors are not presently occurring, and before

removing the degraded drive, consider using Insight Manager to examine the error counters

recorded for each physical drive in the array.

•The customer must follow Compaq cabling guidelines when configuring an array to

implement the best possible cabling solution for his server.

•The customer should check for cabling configurations that are not supported. Signal integrity

errors may be injected into the SCSI bus when an active drive is hot-plugged.

•The customer should make sure fault tolerance is not currently being used to recover from

errors to other drives in the array, such as media errors or signal integrity errors. Loss of fault

tolerance following a drive replacement may result in problems.

•If the customer is upgrading to larger drives in the array, follow the previously stated rules

and ensure that each drive has completed its rebuild before adding the next new drive to the

array.

Hot-Plug Disk Drive Removal and Replacement Guidelines for Compaq Smart Array Controllers 5

11DT-119A-WWEN

Table 1 shows hot-plug hard drive LED indicator status combinations.

Table 1

Hot-Plug Hard Drive LED Indicator Status Combinations

Activity 2

Online 3Fault Means

On Off Off Do not remove the drive. Removing a

drive during this process will cause data

loss.

The drive is being accessed and is not

configured as part of an array.

On Flashing Off Do not remove the drive. Removing a

drive during this process will cause data

loss.

The drive is rebuilding or undergoing capacity

expansion.

Flashing Flashing Flashing Do not remove the drive. Removing a

drive during this process will cause data

loss.

The drive is part of an array being selected

by the Array Configuration Utility.

-Or-

The Options ROMPaq is upgrading the drive.

Off Off Off OK to replace the drive online if a predictive

failure alert is received (see the following

section for details) and the drive is attached

to an array controller.

The drive is not configured as part of an

array.

-Or-

If this drive is part of an array, then a

powered-on controller is not accessing the

drive.

-Or-

The drive is configured as an online spare.

CAUTION: In extreme cases, when the number of errors is greater than the firmware error recovery is able

to sustain, hot-plugging on an online drive may cause some unrecoverable errors to be reported to the

operating system or may cause a complete failure of the array. Refer to your operating system

documentation for more information on implications, as well as possible recovery options.

IMPORTANT: Before replacing a degraded drive, use Compaq Insight Manager to examine the error

counters recorded for each physical drive in the array to verify that such errors are not presently occurring.

Hot-Plug Disk Drive Removal and Replacement Guidelines for Compaq Smart Array Controllers 6

11DT-119A-WWEN

The system administrator should also be aware of the following Compaq guidelines cautioning

unsafe hot-plug replacement:

•Do not remove a degraded drive if any other member of the array is off-line (the online LED

indicator is off). No other drive in the array can be hot-plugged without data loss with the

possible exception of utilizing RAID 0+1 as a fault tolerant form.

Refer to your Smart Array Controller’s user guide for information on fault tolerance options.

•Do not remove a degraded drive if any member of an array is missing (previously removed

and not yet replaced).

•Do not remove a degraded drive if any member of an array is being rebuilt unless the drive

being rebuilt has been configured as an online spare. The drive’s

online LED indicators will be flashing, indicating that a replaced drive is being rebuilt from

data stored on the other drives.

Note: An online spare will not activate and start rebuilding after a predictive failure alert, as the degraded

drive is still online. The online spare only activates after a drive in the array has failed.

•Do not replace multiple degraded drives at the same time (for example, when the system is

off), since the fault-tolerance may be compromised. When a drive is replaced, the controller

uses data from the other drives in the array to reconstruct data on the replacement drive. If

more than one drive is removed, a complete data set is not available to reconstruct data on the

replacement drive(s) and permanent data loss could occur.

CAUTION: Do not turn off an attached disk enclosure when the server containing the Smart Array

Controller is powered on. Also, do not turn on the server before turning on the disk enclosure. If these

ordering rules are not followed, the Smart Array Controller may mark these external drives as “failed,” which

could result in permanent data loss.

Conclusion

Compaq provides superior rapid recovery features in its Compaq Smart Array Controllers that

include hot-pluggable hard drives for high availability. In order to achieve maximum availability,

however, customers should follow the recommended Compaq guidelines for removal and

replacement.

Otros manuales para 179740-001 - ProLiant - 3000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Compaq

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manual de instrucciones

Compaq

Compaq Storage Works ESL9198 Series Manual de instalación y operación

Compaq

Compaq 157767-001 - AIT Drive 50/100 Tape Manual de usuario

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manual de usuario

Compaq

Compaq BL10e - HP ProLiant - 512 MB RAM Manual de usuario

Compaq

Compaq TA1000 Manual de usuario

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manual de instrucciones

Compaq

Compaq SW TL881 DLT Mini-Lib/1 Manual de usuario

Compaq

Compaq SSL2000 Series Manual de usuario

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manual de usuario

Compaq

Compaq 219700-001 - ProLiant - 1500 Manual de usuario

Compaq

Compaq RA8000/ESA12000 Manual de instalación y funcionamiento

Compaq

Compaq StorageWorks ESL9000 Series Manual de usuario

Compaq

Compaq SW TL881 DLT Mini-Lib/1 Manual de usuario

Compaq

Compaq StorageWorks ESL9000 Series Manual de usuario

Compaq

Compaq SLR Tape Drive Manual de usuario

Compaq

Compaq 157770-001 - DAT Drive 20/40 Tape Manual de instrucciones

Compaq

Compaq StorageWorks 4000 - RAID Array Guía de referencia rápida

Compaq

Compaq ProLiant Manual de usuario

Compaq

Compaq StorageWorks MSL5026DLX Manual de usuario

Compaq

Compaq 230050-001 - StorageWorks NAS B3000 Model N900... Manual de usuario

Compaq

Compaq AIT 35 LVD Manual de usuario

Compaq

Compaq DL760 - ProLiant - 1 GB RAM Manual de usuario

Compaq

Compaq SW TL881 DLT Mini-Lib/1 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario