Comnet CWGE2SCS2 Guía de inicio rápido

INS_CWGE2SC(M,S)2_REV- 06/22/12 PAGE 1

INSTALLATION AND OPERATION MANUAL

CWGE2SC(M,S)2

COMMERCIAL GRADE 10/100/1000BASE-T(X) TO

1000BASE-SX/LX GIGABIT ETHERNET MEDIA CONVERTER

The ComNet™CWGE2SC(M,S)2 Ethernet media converters are designed to transmit

and receive 10/100/1000 Mbps data over multimode or single mode optical fiber.

The electrical interface will Auto-Negotiate to a 10, 100, or 1000 Mbps Ethernet rate

without any adjustments. The optical interface operates at a 1000 Mbps Ethernet

rate. These media converters are commercial grade for light industrial use.

Indicating LEDs are provided for confirming operating status. See Figure 4 on

Page 3 for LED explanations.

See Figures 1 – 5for complete operation instructions.

INS_CWGE2SC(M,S)2_REV- 06/22/12 PAGE 2

TECH SUPPORT: 1.888.678.9427

INSTALLATION AND OPERATION MANUAL CWGE2SC(M,S)2

FIGURE 2 – CWGE2SC(M,S)2 TRANSCEIVER

FIGURE 1 – CWGE2SC(M,S)2 TRANSCEIVER

REAR PANELFRONT PANEL

2.5mm Center Positive Plug

Operating Voltage: 9 to 12 VDC

Power Consumption: 2W

FIGURE 3 – POSSIBLE ETHERNET CONFIGURATION

Ethernet IEEE 802.3

Network Element

Ethernet IEEE 802.3

Network Element

CWGE2SCM2 CWGE2SCM2

CAT5e/6 with

RJ45 Connections

CAT5e/6 with

RJ45 Connections

2 OPTICAL FIBERS

SC CONNECTORS

MULTIMODE

Ethernet IEEE 802.3 Network Element determined by user.

INS_CWGE2SC(M,S)2_REV- 06/22/12 PAGE 3

TECH SUPPORT: 1.888.678.9427

INSTALLATION AND OPERATION MANUAL CWGE2SC(M,S)2

FIGURE 4 – INDICATING LEDS

FIGURE 5 – DIP SWITCH POSITIONS

LED Status Meaning

Power On Power is on

Link/ACT (FP) On Fiber link port is connceted

Flashing Packets sending/receiving

Link/ACT (TP) On TX port is connected

Flashing Packets sending/receiving on TX port

FDX/COL On TX port full duplex mode active

Off TX port half duplex mode active

FX or SD On Fiber signal is detected

1000M On TX in 1000 Mbps speed

Off TX in 100 Mbps speed

Function

DIP Switch Position

1 2 3 4

Link Fault Pass-through function. DIP Switches 1 and 4 must be set

to opposite positions (default is 1 ON/4 OFF)

OFF/

ON/

OFF

Pass-through Mode / Enable Jumbo Frame ON ON

Enable Store and Forward Mode (default) OFF OFF

Modified Cut-through mode ON OFF

INS_CWGE2SC(M,S)2_REV- 06/22/12 PAGE 4

3 CORPORATE DRIVE | DANBURY, CT 06810 | USA

T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET

8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE

T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET

INSTALLATION CONSIDERATIONS

This fiber-optic link is supplied as a Standalone module. Units should be installed in dry locations protected from extremes of temperature and humidity.

CAUTION: Take care not to press on any of the LEDs.

WARNING: Unit is to be used with a Listed Class 2 power supply.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than

room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma)

specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

MECHANICAL INSTALLATION INSTRUCTIONS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Comnet