Comm Net Systems TPA 250 Fuse Panel Series Manual de instrucciones

SETUP AND OPERATION MANUAL

FOR TELECOM BROADBAND

TPA 250 Fuse Panel

Comm/net Systems, Inc.®

4237 – 24th Avenue West

Seattle, WA 98199

TEL: 206.282.8670

FAX: 206.282.8684

www.commnetsystems.com

24/7 Sales & Service

To purchase Comm/net Systems solutions, contact your

Comm/net Systems representative at: (800) 274-0544

or e-mail: [email protected]

About Comm/net Systems

Comm/net Systems, Inc.® (CSI) is the leader in high power density communications power

systems. Comm/net oﬀers comprehensive power and communications site systems integration

and deployment services via a national footprint of regional branch oﬃces. Additional

information can be found at www.commnetsystems.com.

Comm/net Systems logo are registered trademarks of Comm/net Systems, Inc.® in the United

States and other countries. All other trademarks, service marks, registered marks, or registered

service marks are the property of their respective owners. Comm/net Systems assumes no

responsibility for any inaccuracies in this document. Comm/net Systems reserves the right to

change, modify, transfer, or otherwise revise this publication without notice.

Document Number: 048-784-30

Revision Level: r01

Published: April 2018

SETUP AND OPERATION MANUAL

FOR TELECOM BROADBAND

TPA 250 Fuse Panel

TPA 250 FUSE PANEL

SETUP AND OPERATION MANUAL

ABOUT THIS MANUAL

About This Manual

To reduce the risk of damage to equipment, injury, or death; and to ensure proper

installation and operation of Comm/net Systems products, please be sure to read and

understand the entirety of this manual and any other supplied documentation. Keep

this document in a safe and accessible place for future reference.

Safety and Alert Symbols

The following symbols may appear in this manual, other supplied documentation, or on Comm/net Systems product labeling. The meaning of

this indication is explained below.

NOTICE

INDICATES IMPORTANT INFORMATION REGARDING THE COMPLETE AND PROPER FUNCTION OF A PRODUCT.

TYPICALLY REFERS TO MONITORING CONFIGURATION OR OTHER NONDANGEROUS SITUATIONS.

CAUTION

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD DAMAGE

EQUIPMENT/PROPERTY OR COULD RESULT IN MINOR OR MODERATE INJURY.

WARNING

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN INJURY OR DEATH.

DANGER

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN SERIOUS INJURY OR DEATH.

Product support

If you have any questions concerning Comm/net Systems products and services, contact our support staﬀ. Our knowledgeable support team

can provide product technical support and answer other questions regarding Comm/net products and services.

In addition to contacting Comm/net Support directly via phone or e-mail, our online help desk is available 24 hours a day, 7 days a week. The

help desk includes answers to commonly asked questions and self-help articles as well as an online ticket submission system if you need to

contact Comm/net after normal business hours.

yComm/net support is available by phone or e-mail Monday – Friday from 8am – 4:30pm Paciﬁc Standard Time.

yThe online web portal is available 24/7 to submit support requests and general questions, or view the FAQ and self-help articles.

NOTE: All questions submitted to the web portal will be answered during normal business hours.

yPhone: 1-800-274-0544

yE-mail: support@commnetsystems.freshdesk.com

yOnline Web Portal: https://commnetsystems.freshdesk.com

TPA 250 FUSE PANEL

SETUP AND OPERATION MANUAL

TABLE OF CONTENTS

Table of Contents

Section 1: Purpose and Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 Product Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Section 2: Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Section 3: Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Section 4: Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1 Installation Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.1 Elevated Operating Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.2 Reduced Air Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.3 Mechanical Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.4 Circuit Overloading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.5 Reliable Earthing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.6 Disconnect Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.2.1 Optional Cable Lacing Bar Kit (750-283-10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.2.2 Optional Rear Rack Support Kit (750-277-10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.3 Chassis Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.4 Input Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.5 Safety Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.6 Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.7 Fuse Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.8 Alarm Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.9 Installation Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Appendix A: Mechanical Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Appendix B: Supported Lugs For Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Appendix C: Output Cable Whips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

C.1 40A Output Connector Cable Whips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

C.2 100A Connector Cable Whips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Appendix D: Supported Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Appendix E: Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

TPA 250 FUSE PANEL

SETUP AND OPERATION MANUAL

PAGE vI -

THIS PAGE INTENTIONALLY LEFT BLANK

TPA 250 FUSE PANEL

SETUP AND OPERATION MANUAL

PURPOSE AND APPLIcAbILITy - PAGE 1

Section 1: Purpose and Applicability

The purpose of this document is to detail the installation and operation instructions

for the TPA 250 Series fuse panel.

1.1 Product Model

This document applies to the following conﬁgurations of the

Comm/net Systems, Inc TPA 250 Series fuse panel:

TABLE 1. TPA 250 SERIES FUSE PANEL CONFIGURATIONS

PART NUMBER DESCRIPTION INPUTS OUTPUTS MONITORING COLOR

016-2121-10 TPA 250; -48VDC; (12) TPA Fuse

Positions

Single-Input 40A Connectorized Standard LEDs White

016-2122-10 TPA 250; -48VDC; (6A/6B) TPA

Fuse Positions

Dual-Input 40A Connectorized Standard LEDs White

016-2123-10 TPA 250; -48VDC; (12) TPA Fuse

Positions

Single-Input 40A Connectorized Meter Module White

016-2124-10 TPA 250; -48VDC; (6A/6B) TPA

Fuse Positions

Dual-Input 40A Connectorized Meter Module White

016-2125-10 TPA 250; -48VDC; (12) TPA Fuse

Positions

Single-Input 100A Connectorized Standard LEDs White

016-2126-10 TPA 250; -48VDC; (6A/6B) TPA

Fuse Positions

Dual-Input 100A Connectorized Standard LEDs White

016-2127-10 TPA 250; -48VDC; (12) TPA Fuse

Positions

Single-Input 100A Connectorized Meter Module White

016-2128-10 TPA 250; -48VDC; (6A/6B) TPA

Fuse Positions

Dual-Input 100A Connectorized Meter Module White

Section 2: Theory of Operation

2.2 Introduction

The TPA 250 Series product family consists of single-input (12 TPA fuse positions)

and dual-input (6A/6B TPA fuse positions) 1RU fuse panels with connectorized outputs

available in 40A or 100A conﬁgurations, along with standard LED front display

monitoring or optional meter module display. TPA fuses are available for this panel in

ratings from 3 ampere up to 50 ampere.

2.3 Features

TPA 250 Series Fuse Panel

yTPA fuse positions: 12; each up to 50A max

yRack mounting: 19 in. or 23 in. rack mount ears

yMounting oﬀset: Front-ﬂush, mid-mount forward, mid-mount rearward

yLED indicators (panels with LED display; Figure 1)

yAdvanced LCD display (panels with meter module; Figure 2)

yAlarm Contacts: Form C dry contacts

ySide-accessible modular jack connections for alarm outputs

yPolarized, positive latching connectorized outputs

yOptional lacing bar kit (750-283-10) or telescoping rear rack support kit (750-277-10)

Figure 1. LED Display

Figure 2. Meter Module

TPA 250 FUSE PANEL

SETUP AND OPERATION MANUAL

PAGE 2 - PURPOSE AND APPLIcAbILITy

THIS PAGE INTENTIONALLY LEFT BLANK

TPA 250 FUSE PANEL

SETUP AND OPERATION MANUAL

UNPAckING AND INSPEcTION - PAGE 3

Section 3: Unpacking and Inspection

The Comm/net Systems TPA 250 Series fuse panel was carefully packaged at the

factory to withstand the normal rigors of shipping. However, you should carefully

inspect the box and contents to conﬁrm that no damage has occurred in transit. Most

shipping carriers require notiﬁcation of shipping damage within twenty-four hours of

delivery, and it is the responsibility of the recipient to inspect the shipment immediately

upon receipt.

3.1 Package Contents

Included with your product are the following items:

yTPA 250 Series fuse panel

yRear lacing bar assembly

yClear plastic input safety covers

yMounting hardware kit with necessary screws and washers

yOptional lacing bar kit or rear rack support kit (if ordered)

Section 4: Installation

4.1 Installation Preparation

When selecting an installation location, ensure that all of the following conditions are

met before proceeding.

4.1.1 Elevated Operating Ambient Temperature

If you install the panel in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient. Therefore,

take care to install the equipment in an environment compatible with the maximum

ambient temperature (TMA) speciﬁed in Section 5.

4.1.2 Reduced Air Flow

Installation of the equipment in a rack should be such that the amount of air ﬂow

required for safe operation of the equipment is not compromised.

4.1.3 Mechanical Loading

Mounting of the equipment in the rack should be such that a hazardous condition is

not achieved due to uneven mechanical loading.

4.1.4 Circuit Overloading

Give consideration to the connection of the equipment to the supply circuit and

the eﬀect that overloading of the circuits might have on overcurrent protection and

supply wiring. Use appropriate consideration for equipment nameplate ratings when

addressing this concern.

4.1.5 Reliable Earthing

Maintain reliable earthing of rack-mounted equipment. Pay particular attention to

supply connections other than direct connections to the branch circuit (e.g., use of power

strips).

4.1.6 Disconnect Device

A readily accessible disconnect device must be incorporated in the building

installation wiring.

TPA 250 FUSE PANEL

SETUP AND OPERATION MANUAL

PAGE 4 - INSTALLATION

4.2 Mounting

NOTICE

yTHIS PRODUCT MUST BE INSTALLED WITHIN A RESTRICTED

ACCESS LOCATION WHERE ACCESS IS THROUGH THE USE

OF A TOOL, LOCK AND KEY, OR OTHER MEANS OF SECURITY,

AND IS CONTROLLED BY THE AUTHORITY RESPONSIBLE

FOR THE LOCATION. THIS PRODUCT MUST BE INSTALLED

AND MAINTAINED ONLY BY QUALIFIED TECHNICIANS.

ySUITABLE FOR MOUNTING ON CONCRETE OR

OTHER NONCOMBUSTIBLE SURFACE ONLY.

Step 1. Select either position 1, 2, or 3 to install the mounting ears (see Figure 3).

Step 2. Attach the mounting ears with included 10-32 hardware (see Figure 4).

Step 3. Select the equipment rack location for installation of the fuse panel then

secure the panel to the equipment rack by tightening hardware into the

mounting ears (see Figure 5).

4.2.1 Optional Cable Lacing Bar Kit (750-283-10)

Step 1. Attach the rear cable lacing bar assembly by tightening the (4) 10-32 socket

head screws into the threaded holes located on each side of the chassis

towards the rear (see Figure 5).

4.2.2 Optional Rear Rack Support Kit (750-277-10)

An optional telescoping rear rack support kit (750-277-10) is available to help secure

the panel to the rear of the equipment rack and to distribute panel weight evenly. In

addition to the standard lacing bar included with the TPA 250 fuse panel, a new lacing

bar is included with this kit which can be repositioned on any of the available lacing bar

holes depending on the depth of the equipment rack. Use a hex key to relocate the new

lacing bar if needed. See Pages 15 & 16 for mechanical dimensions of rear rack support

kit.

Step 1. Slide the rails of the rear rack support assembly into the lacing bar assembly

from section 4.2.1 (see Figure 6).

Step 2. Secure the mounting ears to equipment rack via the slotted holes or PEM nuts.

Figure 6. Rear Rack Support Kit (750-277-10)

Figure 4. Mounting Ears (Postion 1 Shown)

Figure 3. Mounting Ear Positions

Figure 5. Cable Lacing Bar Kit (750-283-10)

Tabla de contenidos

Otros manuales de Hardware de red de Comm Net Systems

Comm Net Systems

Comm Net Systems GMT 125 Fuse Panel Manual de instrucciones

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario