COMedia C8203E-0426 Manual de usuario
Page 1 of 3 Rev 1
C8203E-0426
DVR Module
HDMI interface
Introduction
This module has been designed for muC10x series and output real time video to HDMI/DVI
monitor. It performs still image capture as well as video recording and store files to SD card. It
has been designed for operation by DC5V or lithium battery.
Key Features
Interface to muC10x series camera
Real time Video output
DVI output HD720p at 30fps
Simple operation for AWB
AVI recording and JPG snap shot
Store to SD card, up to 32G
Image quality fine tune possible
RTC with battery backup
Battery level detect and display on
screen
5VDC or 4.2V Li-ion battery operated
Built in battery charging
Individual GPIO for key input
Block Diagram
Connectors of module
Key board layout
COMedia Ltd.
康大科技有限公司
A82
OV426
Keyboard
Micro
SD Card
HDMI/
DVI
DC5V/4.2V
DVP
6946
SPI
Flash SDRAM
RTC
Charging
Batt detect
LED
PC
USB
DC input
BATT input
LED out
Camera Keyboard
USB HDMI OUT
Note: connectors not labeled
in this diagram are reserved
for other optional cameras
μSD card slot
(Bottom side)
OK
LF
PWR MENU
UP
RT
DN
Page 2 of 3 Rev 1
Operation
1. Power on off the module
a. Connect HDMI cable to external HD monitor
b. Apply DC or battery accordingly. Please note the module is configured in different
operation voltage, apply inappropriate voltage will damage the module.
c. Connect camera module
d. Press PWR key and turn on the system. Video will be displayed in the center of
the monitor, and OSD on the upper right corner
2. White balance calibration
a. Press DN key, it will perform color balance
3. LED output control
a. Press UP key to toggle external LED on and off
b. By default, it will be on at power up
4. Record video clip and snap still picture
a. Make sure micro SD card is existed before capture
b. Press LF to snap a still picture, a camera icon will be flashed once in the center
of display
c. Press RT to start video recording, press again RT to stop. When recording a red
dot as well as timer will display on the upper right corner of display
d. Maximum recording duration is 30min.
5. Menu operation
a. Press MENU to enter menu display
b. Use UP/DN key select item, and use LF/RT to change value,
use OK key to confirm and quit
i. Brightness : 1-9
ii. Contrast : 1-9
iii. Sharpness : 1-5
Batt Check: OFF/ON
iv. Reset file number : clear file number and start from
IM_00001, effective from next time capture
6. Date time setup
a. Press MENU and hold for 2 second then release, it will enter D/T setup menu
b. Use UP/DN to increase or decrease digit, use LF/RT to move field, OK to quit.
7. Battery detect and charging
a. At preview mode, a battery icon will display on the upper right corner to show the
status of battery. If it is set to off the battery detect, no icon will be displayed.
b. If battery is low, an empty battery symbol will be flashing on the center of monitor
for few second and shut down the system automatically.
c. Connect external DC for charging. Depends on the power configure, use 12V for
H version and 5V for E version.
d. If the system use external DC and no battery attached, please set battery detect
off in menu
8. Play back video files
a. Pick out the micro SD card and play it in PC or
b. Connect module to PC thru USB cable.
BRIGHTNESS 5
SATURATION 4
CONTRAST 3
SHARPNESS 1
BATT CHECK OFF
RESET FILE NUMBER
FACTORY DEFAULT
SAVE & EXIT
FW VER: 20170304
SD
2017/0/01
12:00:30
2017/02/12 11:12:43
Page 3 of 3 Rev 1
9. Connect to PC
a. It is mass storage device, like external hard disk for PC
b. When connected, HD monitor will show “USB connected” and PC screen will pop
up the window to show the content of the micro SD card installed on the module.
No other module operation will be performed in this mode
c. If there is no SD card installed, it will not enter mass storage mode.
d. Video files is placed under folder of DCVD, file name is IM_0xxxx.avi or
IM_0xxxx.jpg
e. When disconnected from PC, the module will turn off automatically.
f. When connected, never remove the SD card from the module, otherwise, system
will hang and SD card may be damaged.
Electrical Characteristics (at room temperature 25C)
Parameter Condition Min Typ. Max Unit
Operation Voltage 3.5 4.2 5.5 V
Operation Current With camera connected but
no LED on
170 140 120 mA
Charging current 5V DC input 1000 mA
LED Output Voltage: same as input, battery or DC
LED Current source: depends on LED forward voltage, limited with 10Ohm resister
Mechanical dimensions
Ordering information
We provide different options for customer to select on his system configuration. Customer can
specify requirement when order placement.
1. By default, the standard configuration is 5V/4.2V battery, with normal size HDMI
connector. Model no is C8203E-0426
2. By PCB option, we can provide higher voltage operation, either 12VDC or 4.2Vx2 battery.
Model no is C8203H-0426
3. The other options are mini size HDMI connector.
Este manual sirve para los siguientes modelos
1
Otros manuales de DVR de COMedia
