COMAC SIMPLA 50B-BT Manual de usuario

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 1 of 16

READ THE USE AND MAINTENANCE MANUAL

Electric System Testing

1. Disconnect the battery connector.

2. Check the functioning of the electric system switches,

motors, solenoid valve, contactors, power fuses and

thermal trip units.

3. Check the condition and tightening of all power cables:

contactors, fuses, motors, etc.

4. Check the functioning and condition of the potentiometer

and the base confirmation microswitches (water and brush

rotation) and working operation, and those for automatic

squeegee rise and descent (AUTOMATIC VERSION only).

5. Check the handlebars lever is centrally positioned and that

the threaded rod does not touch the measuring device

card located beneath the instrument panel (if it does touch,

adjust it within the plastic joints.

6. Check the condition and connections of the battery poles on

the battery connector.

7. Reconnect the battery connector.

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 2 of 16

8. Check the functioning of the chopper.

9. If necessary, calibrate the chopper card as

follows:

•raise the machine (free traction wheels);

•unscrew the rear instrument panel to access

the chopper;

•set the continuous voltage measurement

tester with a full scale of 50V;

•insert the test prods on the fastons marked

with M+ and M- on the chopper card;

•switch on via the main key;

•select the forward movement until activating

the movement microswitch (so you can hear

the click of the relays) slightly rotating the

potentiometer on the handlebars with respect

to zero;

•in that moment, the voltage measured by the

test prod must be 3-5V. If necessary, adjust

the VMIN trimmer so the output voltage is at

the required value;

•at this point, press the operation levers fully

down until you reach maximum speed. You

should see a value of 24V (battery

maximum); if this is not the case, adjust the

VMAX trimmer to obtain the required output

voltage;

•acceleration adjustment: rotate the ACC

trimmer clockwise. This adjustment brings the

voltage to the maximum required value (24V)

in about 7-8 seconds;

•check the reverse gear is functioning;

•check the motor braking (releasing the

accelerator, the machine must stop within

about 1 metre)

Adjusting the battery charger

1. Check the set-up of the battery charger corresponds to the

type of battery actually installed on the machine.

2. To adjust the battery charger, proceed as follows:

•use a screwdriver to remove the small plastic cap;

•set the dip switches inside, on the basis of the table

below;

•close the plastic cap

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 3 of 16

The dip switches are set as follows (DP1 and DP2 are the SW1

and DP3 and DP4 are SW2):

DP1 DP2 SET-UP

OFF OFF EXIDE SONNENSCHEIN gel

OFF ON General GEL or AGM batteries

ON OFF Wet-cell batteries

ON ON TROJAN gel

DP3:

ON for all the batteries (not used)

DP4:

OFF for all the batteries (not used)

Carefully read the battery charger operating manual

Battery charger alarm signals:

Flashing YELLOW LED:

•WRONG BATTERY

•BATTERY NOT CONNECTED

•OUTPUT SHORT-CIRCUIT

Flashing RED LED:

•SAFETY TIMER EXCEEDED

•INTERNAL SHORT-CIRCUIT

Initial battery charger test:

GREEN LED with 2 flashes: battery charger with set-up for GEL or AGM batteries

RED LED with 2 flashes: battery charger with set-up for wet-cell batteries

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 4 of 16

Check the functioning of the “service menu”. Remember that to access it, you must keep the

button pressed while starting up the machine (when you turn the key).

Keeping the button pressed for

a few seconds will zero-set the

total hour-counter (only in the

first hour of operation).

Pressing the button

Keeping the button pressed

for a few seconds will zero-

set partial hour-counter 1.

Pressing the button

Pressing

the button

Keeping the button pressed for

a few seconds will zero-set

partial hour-counter 2.

Pressing the button

Keeping the button pressed for

a few seconds will change the

battery technology setting.

Keeping the button pressed

for a few seconds will give

you access to the “service”

sub-menu: every time the

button is subsequently

pressed, the setting will

Pressing the button

Keeping the button pressed for a

few seconds will zero-set the

number of loads.

Pressing the button

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 5 of 16

Water System Testing

1. Check the solution filter just underneath the tank cap is

clean and functioning.

2. Check the cleanliness and seal of the solution filter (in the

rear part of the machine, at frame level).

3. Completely fill the solution tank with water.

4. Check the seal of the tubes, the solenoid valve, and the

water tap adjustment.

5. Check the solution pours onto the floor in a continuous

manner when the tap is open.

Adjusting the brakes

1. Fix the brake cable to the frame, tightening the sheath

completely down on the support.

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 6 of 16

2. Adjust the pads on the wheels, so that when the pin is

inserted on the handbrake lever, the machine is blocked.

3. To adjust the pads, proceed as follows:

•loosen the M8 locknut

•Loosen or tighten the pad so that it is correctly adjusted

(make sure that with the machine working, batteries

installed, the pad does not touch the wheel).

•tighten the M8 locknut

Suction Testing

1. Check the filter – float is clean and functioning.

2. Check the air seal of the cap on the recovery tank.

3. Check the connections and seal of the suction tubes and the

squeegee tube.

4. Check the seal of the squeegee nozzle.

5. Check the seal of the drainage tube and cap.

6. Adjusting the suction microswitch (MANUAL MACHINE

VERSION):

•adjust the microswitch so that when the lever is turned, the

switch closes (thereby activating the suction), leaving a gap

of about 0.5mm between the roller and the main body

•after adjusting, check the microswitch is functioning

correctly

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 7 of 16

7. Adjusting the suction microswitch (AUTOMATIC MACHINE

VERSION):

•adjust the upper microswitch so that when the cam is

turned, the switch closes, leaving the squeegee 4-5cm

above the ground

•adjust the lower microswitch so that when the cam is

turned, the switch closes with the squeegee on the ground

(thereby activating the suction)

•after adjusting, check the microswitch is functioning

correctly

Adjusting the Washing Base (55BT and 65BT)

- MANUAL VERSION MACHINE -

1. With the pedal fixed in place, check the base confirmation

microswitch changes over and the roller remains about

0.5mm from the main body of the switch.

2. If necessary, adjust the microswitch as follows:

•loosen the M3 locknut and the relative M3 screw;

•move the microswitch in its slot;

•fix the M3 locknut and relative M3 screw until the

microswitch is blocked, taking care not to over-tighten

(and therefore damage the device itself);

•after adjusting, check the microswitch is functioning

correctly and, if necessary, repeat the calibration.

3. Carry out a functional test to check that, with the base

down, the brushes begin turning when the machine is set for

working operation.

4. Check the brushes can be easily disassembled and that there

is enough space for the fixing buttons to pass beneath the

brush-holder plates. If the brushes are not clean:

•lift the base;

•loosen the M6 locknut;

•loosen the M6 screw until there is enough space to affix

and remove the brushes from the base;

•at the same time, check the base does not interfere with

the solution tank.

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 8 of 16

- AUTOMATIC VERSION MACHINE -

5. Ensure that the base microswitch block the operation of

the brushes when the base is lifted a few centimetres from the

ground.

6. If necessary, adjust the blade of the microswitch.

7. Carry out a functional test to check that, with the base down,

the brushes begin turning when the machine is set for working

operation.

8. For the correct height of the base, check that the thread of the

stem protrudes about 5 mm. Ensure that the brushes can be

easily removed and that there is sufficient space for the

passage of the fastening buttons below the brush holder

plates. Otherwise act on the thread adjustment.

9. Check the adjustment of the base lowering limit switches

in order to give the correct pressure of the base to the ground.

Pay attention that in the event of excessive pressure, the

wheels may rise slightly.

10. Check that when lifting, the base does not touch the tank and

when lowering without brushes it does not touch the floor.

Otherwise, proceed as follows:

•Using a small screwdriver as a lever, remove the plastic

cover of the microswitches inside the jack;

•Loosen the screws holding the micro sliding them to

determine the correct position;

•Tighten the screws;

•Replace the plastic cover;

•Perform a functional test.

11. Adjust the belt-stretcher spring to a length of 27mm under

compression.

12. Adjust the transversal inclination of the base:

•position the machine on an even, flat floor

•lower the base onto the floor with the brushes assembled

•loosen the screw and M8 nut that fix the left lifting arm

to the base

•rest the base on the floor so that the brushes touch the

floor simultaneously

•tighten the M8 screw and the locknut

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 9 of 16

13. Check the M8 screw that fixes the arm to the third point

allows the longitudinal movement of the base, so this can

adjust itself to the specific floor.

14. If the base vibrates because of the brush or pad movement,

tighten the nut to further compress the spring and soften the

vibrations.

Adjusting the Washing Base (50BST)

1. Ensure that the brushes can be easily removed and that there

is sufficient space for their passage. If the brushes are not

clean:

•lift the base;

•loosen the M6 locknut;

•loosen the M6 screw until there is enough space to affix

and remove the brushes from the base;

•at the same time, check the base does not interfere with

the solution tank.

2. Adjust the transversal inclination of the base:

•position the machine on an even, flat floor

•lower the base onto the floor with the brushes assembled

•loosen the screw and M8 nut that fix the left lifting arm

to the base

•rest the base on the floor so that the brushes touch the

floor simultaneously

•tighten the M8 screw and the locknut

3. Check the M8 screw that fixes the arm to the third point

allows the longitudinal movement of the base, so this can

adjust itself to the specific floor.

ADJUSTMENTS

AND

TESTING

SIMPLA 50B-BT

SIMPLA 55BT

SIMPLA 65BT

SIMPLA 50BST

Doc. 10021896

Issued 09/2010

Ver. AB

Page 10 of 16

4. Adjust the pressure relief spring by tightening the M6 screw

on the tie rod until 5-6 mm of thread remain, so as to obtain

the correct pressure on the base.

5. Assemble the transmission coupling so that there are 2 mm.

between the two hubs and that the rubber toothed star

situated between the two works properly, no vibrations or

misalignments.

6. Tighten the dowels and related nuts.

7. Adjust the drive belt tension by means of the

M8 nut, so that the thread protrudes from the support by

approx. 28-29 mm.

Refer to the WASHING version for the adjust of the automatic version.

Adjusting the Washing Base (50 B-BT)

1. With the pedal fixed in place, check the base confirmation

microswitch changes over and the roller remains about

0.5mm from the main body of the switch.

2. If necessary, adjust the microswitch as follows:

•loosen the M3 locknut and the relative M3 screw;

•move the microswitch in its slot;

•fix the M3 locknut and relative M3 screw until the

microswitch is blocked, taking care not to over-tighten

(and therefore damage the device itself);

•after adjusting, check the microswitch is functioning

correctly and, if necessary, repeat the calibration.

3. Carry out a functional test to check that, with the base

down, the brushes begin turning when the machine is set for

working operation.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de piso de COMAC

COMAC

COMAC C85bs nsc Manual de usuario

COMAC

COMAC INNOVA 2011 Manual de usuario

COMAC

COMAC MEDIA 65BT-75BT-60SBT Manual de usuario

COMAC

COMAC SIMPLA 55BT Manual de instalación y operación

COMAC

COMAC VISPA 35B Manual de usuario

COMAC

COMAC CS 60 II Manual de usuario

COMAC

COMAC SIMPLA 55BT Manual de usuario

COMAC

COMAC SIMPLA 50 BS Manual

COMAC

COMAC Vispa 35E Manual de instrucciones

COMAC

COMAC CS60 2016 B Manual de usuario

COMAC

COMAC CS50 B-BT Manual de usuario

COMAC

COMAC ULTRA 85BS Manual de instrucciones

COMAC

COMAC OMNIA 26 Manual de usuario

COMAC

COMAC INNOVA 55B Manual de usuario

COMAC

COMAC ABILA17 B Manual de usuario

COMAC

COMAC CS80 B Manual de usuario

COMAC

COMAC CS700 B 2021 Manual de usuario

COMAC

COMAC MEDIA 26III B Manual de instrucciones

COMAC

COMAC L20 B-E Manual de usuario

COMAC

COMAC CS90 D Manual de usuario

COMAC

COMAC CM 50 hs Manual de usuario

COMAC

COMAC CS80 Series Manual de usuario

COMAC

COMAC CM1500 S Manual de usuario

COMAC

COMAC ANTEA 50E Manual de usuario

Manuales populares de Máquina de piso de otras marcas

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manual de usuario

Numatic

Numatic ET 4045 Manual de usuario

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manual de usuario

Mytee

Mytee 8070 Mytee-Lite Manual de usuario

Kärcher

Kärcher B 140 R Manual de usuario

Triple S

Triple S Ace 26T1 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance SW 750 Manual de usuario

Tornado

Tornado Marathon 2000 98190 Manual

Windsor

Windsor ADMIRAL Admiral 8 Manual de usuario

Numatic

Numatic TTB 1117/100 Manual de usuario

Tennant

Tennant 8210D Manual de usuario

Nobles

Nobles Frontier Manual del producto

lavina

lavina 21-X Manual de usuario

KENT

KENT Edge 28B Manual de usuario

Tennant

Tennant 215 Manual del producto

Windsor

Windsor BDP 51/2000C Manual de usuario

CleanFreak

CleanFreak DURA-18HD Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guía del administrador