Coemar Strip lite Manual de usuario
manuale di istruzioni
instructions manual
Version 1.0
strip lite LED RGB
strip Lite LED RGB
numero di serie/serial number
data di acquisto/date of purchase
fornitore/retailer
indirizzo/address
cap/città/suburb
provincia/capital city
stato/state
tel./fax/
Prendete nota, nello spazio apposito, dei dati relativi al modello e al rivenditore del vostro Strip Lite Led RGB:
questi dati ci permetteranno di assistervi con la massima rapidità e precisione.
Please note in the space provided above the relative service information of the model and the retailer from
whom you purchased your
Strip Lite Led RGB
: this information will assist us in providing spare parts, repairs
or in answering any technical enquiries with the utmost speed and accuracy.
ATTENZIONE
:
la sicurezza dell’apparecchio è garantita solo con l’uso appropriato delle presenti istruzioni, per-
tanto è necessario conservarle.
WARNING
: t
he security of the fixture is granted only if these instructions are strictly followed; therefore it is
absolutely necessary to keep this manual.
Users Manual Version 1.0
edition February 2007
Index
1. Packaging and transportation Pag. 28
1.1. Packaging “28
1.2. Transportation “28
2. General information Pag. 28
2.1. Important safety information “28
2.2. Warranty conditions “28
2.3. Certification “28
3. Product specifications Pag. 29
3.1. Technical characteristics “29
3.2. Strip Lite Led 1mt dimensions “29
3.3. Strip Lite Led 4ft dimensions “30
3.4. Projector components “30
4. Installation Pag. 31
4.1. Mechanical installation “31
4.2. Attaching a safety chain “32
4.3. Adjusting beam direction “32
4.4. Adjusting the beam angle “33
5. Powering up Pag. 35
5.1. Operating voltage and frequency “35
5.2. Mains connection “35
6. DMX signal functions Pag. 36
6.1. Connecting DMX signal “36
6.2. Powering up “36
6.3. DMX addressing “37
6.4. DMX functions 6 channels “37
6.4. DMX functions 10 channels “38
7. Test function Pag. 38
8. Light ON function Pag. 39
9. Compact 6 Ch function Pag. 39
10. Auto function Pag. 40
10.1. Master/Slave mode “40
10.2. Stand Alone mode “41
11. DR1 function Pag. 42
11.1. Functions using DR1 (MODE) “43
11.2. Setting up functionality using DR1 (FUNC) “43
11.3. Diagnostic functions using DR1 (MEAS) “44
11.4. Electronic alignment and software upgrade “44
11.5. Error messages using DR1 “46
12. Switch panel signals Pag. 46
13. Maintenance Pag. 46
13.1. Replacing blown fuses “46
13.2. Periodic maintenance “47
14. Spare parts Pag. 47
15. Frequently asked questions Pag. 47
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture of the highest quality, both in compo-
nentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expe-
dite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). This
information will assist in providing prompt and accurate advice from your Coemar service centre..
Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to come.
1.1. Packaging
Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the equipment,
contact your carrier immediately by telephone or fax, following this with formal notification in writing.
Packing list
Ensure the packaging contains:
1 Strip Lite Led RGB
1 Instruction manual
2 cam-lock support brackets
1.2. Transportation
The Strip Lite Led RGB should be transported in either its original packaging or in an appropriate flight case.
2.1. Important safety information
Fire prevention:
1. Never locate the fixture on a flammable surface.
2. Minimum distance from flammable materials: 0.5 m.
3. Minimum distance from the closest illuminable surface: 0,5 m.
4. Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt.
5. Connect the projector to mains power via a thermal magnetic circuit breaker.
Prevention against electric shock:
1. High voltage is present in the internal of the unit. Isolate the projector from mains supply prior to performing any function which
involves touching the internal of the unit.
2. For mains connection, adhere strictly to the guidelines outlined in this manual.
3. The level of technology inherent in the Strip Lite Led RGB requires the use of specialised personnel for all service applications; refer
all work to your authorised Coemar service centre.
4. A good earth connection is essential for proper functioning of the projector. Never operate the unit without proper earth connection.
5. The mains cable should not come into contact with other cabling.
6. Never handle the unit with wet hands or in a damp environment.
Safety:
1. The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the weight of the unit.
2. Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the primary fixing point.
3. Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.
4. The external surface of the unit, at various points, may exceed 80°C. Never handle the unit until at least 10 minutes have elapsed
since the unit was turned off..
Protection rating of the body against liquids and solids:
1. The fixture is classified ordinary apparatus; its protection grade against penetration by external agents,solid or liquid, is IP 20
2.2. Warranty conditions
1. The fixture is guaranteed for a period of 12 months against manufacturing faults and faulty materials.
2. Faults due to incorrect operation or operation in an inappropriate manner are not covered by the warranty.
3. The warranty is immediately void if the fixture has been operated or serviced by unqualified or unauthorised personnel.
4. The warranty does not include fixture replacement.
5. The model and serial numbers must be supplied for any warranty claims or advice from our authorised service personnel.
2.3. Certification
1. The fixture satisfies the essential requirements of the directive EMC 89/336/EEC, 93/68/EEC, BT73/23/EEC.
2. The fixture is in accordance with the standard EN 50419 (RoHS) and satisfies the requirements of the directive 2002/96/EC (WEEE).
2. General information
1. Packaging and transportation
4
English
3.1. Technical characteristics
Power: 90/240 Vac 50/60Hz Autosensing
Nominal current: 0.5A @ 230Vac
1.1A @ 115V
Power factor: cos ϕ = 0.8
Led power: 20 Led x 3W (1mt)
24 Led x 3W (4ft)
Minimum ambient temperature: -15°C / 5°F
Maximum ambient temperature: 35°C / 95°F
Weight: 7.7 Kg / 16.9 lbs
8.5 Kg / 18.7 lbs
IP Rating: IP20
3.2. Strip Lite Led 1mt dimensions
118mm
4.64”
152mm
6”
1009mm
39.72” 95mm
3.75”
42mm
1.65”
757mm
29.8”
200mm
7.87”
Versione Standard
Standard version
Versione con supporto
optional cod. 8052
Version with optional
support cod. 8052
207mm
8.17”
983mm
38.71” 220mm
8.66”
1027mm
40.44”
100mm
3.94”
3. Product specifications
5
English
6
3.3. Strip Lite Led 4ft dimensions
3.4. Projector components
The principal components of the Strip Lite Led RGB are shown in the diagram below.
Components description
1. Side panel
2. Led control PCB
3. PCB group
4. Lens group
5. Front frame
6. Switching power supply
968mm
38.11”
100mm
3.94” 1194mm
47.02” 220mm
8.66”
200mm
7.87”
Versione Standard
Standard version
Versione con supporto
optional cod. 8052
Version with optional
support cod. 8052
95mm
3.75”
42mm
1.65”
118mm
4.64”
152mm
6”
1220mm
4 ft
207mm
8.17”
1238mm
48.75”
English
4.1. Mechanical installation
Strip Lite Led RGB may be floor mounted or hung from an appropriate structure in any position.
Mobile installations
If hanging the fixture from a lighting truss or similar, we recommend the use of appropriate clamps “B”, affixed to the fixture in the holes
“A” provided, as shown in the following diagram.
Floor mounted installations
If the fixture is floor mounted, we recommend the use of appropriate clamps “C” (optional cod.8052), as shown in the following diagram.
ATTENTION!!
Always ensure that your support structure and fixings (bolts, clamps, etc.)
are rated to support the weight of the fixture.
757mm
29.8”
A
B
4. Installation
7
English
4.2. Safety chain
When hanging the Strip Lite Led RGB we recommend the use of a safety chain “D” affixed to the yoke and to the suspension device. The safety
chain should be either a metal wire rope or a metal chain, both suitably rated for the purpose.
4.3. Adjusting beam direction
If the Strip Lite Led RGB is floor mounted, it can be tilted to adjust the beam output. To perform this adjustment, follow the instruc-
tions set out below.
1. Loosen the handles “E” located on the side of the projector, thus allowing the inclination to be changed.
2. Adjust the projector’s tilt.
3. Refasten the handles “E” on the side of the projector.
90°90°
8
English
4.4. Adjusting the beam angle
Three optical groups are available for Strip Lite Led RGB. They are used to vary the beam dimension and make it suitable for different
lighting applications.
The standard optical group, fitted on Strip Lite Led RGB, is composed by a group of lenses that gives 12° beam angle.
Here following you will find instructions to install different optical groups.
1. Remove the screws “F”.
1. Remove the front frame “G” and the plexiglass “H”.
3. Remove the screws “L”.
9
English
4. Replace the lenses “M” and ensure that the led fit perfectly in the lenses seats
The optical groups are asymmetrical and of three different kinds. While groups M1 and M3 can not be inverted, groups M2 can.
A label in the bottom part of the optical group reports the characteristics of the lenses and their type, in order to facilitate the assembly.
5. Tighten the “L” fixing screws.
6. Insert the plexiglass “H” and the front frame “G” as per their original positions.
7. Tighten the “F” fixing screws.
The following table details the range of beam angle available for the Strip Lite Led RGB.
Strip Lite Led type Optical group Beam angle
RGB 1mt Narrow lenses (standard, cod. 8053/13) 12°
RGB 1mt Medium lenses (cod. 8053/21) 23°
RGB 1mt Wide lenses (cod. 8053/5) 35°
RGB 4ft Narrow lenses (standard, cod. 8053/9) 12°
RGB 4ft Medium lenses (cod. 8053/17) 23°
RGB 4ft Wide lenses (cod. 8053/1) 35°
ATTENTION!!
The optical groups are asymmetrical. Pay attention to their assembly position.
10
English
Tabla de contenidos
