CODELOCKS CL50 Manual de usuario

24/9/2561 KA-01054 · Customer Self-Service

https://support.codelocks.com/knowledgebase/article/KA-01054/en-us 1/4

Home (/) > Knowledge Base - Home (/knowledgebase/) > KA-01054

CL50 - 2018 Code Change

Instructions

Push Button Lock

Push button locks can be used at home on doors, garages and garden sheds, and at work in offices,

workshops and storerooms requiring restricted access. Available in Silver Grey.





24/9/2561 KA-01054 · Customer Self-Service

https://support.codelocks.com/knowledgebase/article/KA-01054/en-us 2/4

Many Codes to Choose From

The code chamber consists of 9 buttons from which the code is selected, and a ‘C’ button which is used to

re-set the chamber after an incorrect entry, and which must always be used as the first digit of a code.

Buttons may only be used ONCE in a code. For example, 1212 is not possible. A code or combination can

be entered in any order or sequence; e.g. 1234 can be 4321 or 1342 or whatever sequence is most

convenient to remember. With 9 buttons, a total of 511 different codes are available, any of which can be

entered in any sequence.

The total is arrived at as follows:

It is recommended that the code is changed regularly to prevent compromise.



Code ChangeInstructions

1.Remove the lock from the door by unscrewing the 2 screws in the back plate.

2. Press the ‘C’ button to reset the chamber and place the lock case on a flat surface with the buttons

down.

3. Remove the 2 red screws and carefully lift off the code chamber plate. Check that all 10 springs are held

in place on the plate.

4. Note that thecoloured code tumblers correspond in position to the existing code. The silver non-code

tumblers fill the other positions. The C tumbler is not coloured.

5. Hold the lock in your hand and depress the ‘C’ button. Keeping the ‘C’ button depressed, use tweezers

to reposition the tumblers to correspond with your new code. The square notches of ALL tumblers MUST

face outwards, with the square tips ON TOP: See diagram below. DO NOT force the tumblers in.

Note: Holding the ‘C’ button depressed whilst re-positioning the tumblers is ESSENTIALto avoid

damaging the internal mechanism. DO NOT attempt to reposition the ‘C’ tumbler.

6. Replace the code chamber plate carefully with the 2 red screws.

7. Check the operation of the new code, and make a written note of it before re-installing the lock.

8. Insert the spindle, with the spring on the code side. On latchbolt locks the spindle must engage the latch

24/9/2561 KA-01054 · Customer Self-Service

https://support.codelocks.com/knowledgebase/article/KA-01054/en-us 3/4

as follows:



Maintainence

No maintenance of the working parts is necessary.DO NOT OIL.To maintain the finish the lock should be

cleaned regularly with a soft cloth. A silicone spray or similar, should be used to provide a protective film

against grit and grime.

Guarantee

If any Codelocks mechanical lock should develop a fault, at any time due to manufacturing, just call the

Codelocks helpline and arrange for it to be repaired free of charge.



Diagnostics

Use these simple guides to diagnose any issues you may have with your lock.

1.On latch locks only. The outside knob and inside handle retract the latch when turned TOWARDS the

door frame.The spindle is positioned at the wrong angle.

>Refer to the installation instructions. Remove lock from door and reposition the spindle as shown in the

instructions. On hold open locks ensure that the blue handing screw on the lever handle plate is in the

correct hole.



2. The knob will not turn after entering the original code.The code does not match the card.

> Remove the lock from the door, turn the lock case upside down and check that the coloured tumblers

correspond with the code on the card. NB: the ‘C’ tumbler is not coloured - but MUST start every code.



3. The knob will not turn after entering a newly changed code.One or more of the code tumblers are the

wrong way around.

> Re-read the code change instructions and check that the square notches on the tumblers face to the

outside edge of the lock with thesquare edgeon top.



24/9/2561 KA-01054 · Customer Self-Service

https://support.codelocks.com/knowledgebase/article/KA-01054/en-us 4/4

4. The latchbolt does not move smoothly in and out.The lock is installed incorrectly.

> Check that the lock is square on the door and positioned accurately over the latch. Check that the latch is

positioned horizontally and parallel to the door surfaces.



5.The inside and outside knobs do not return easily to the centre position after use.The spindle is too long

for the door thickness.

> The spindle must not project more than 30mm (1⁄") into the inside handle. If it does then it will be

trapped between the front and back handles and prevent them moving easily. The spindle must be

shortened.



6. The inside handle does not retract the latch.The spindle is too short for the door thickness.

> The spindle must project from the inside face of the door by at least 8mm (⁄") so as to engage the

handle. The spindle may have been cut too short during installation. Call the helpline to obtain a longer

spindle.



7. The inside lever handle does not return to the upright position after operating.The lever return spring is

broken.

> Replacement spring required.



8. The latch does not engage and so the door remains unlocked after use.The latch is not entering the

strike.

> Your door or frame may have warped since the lock was installed. Check that the latchbolt is lined up

with the strike aperture and adjust the position of the strike as necessary. Make sure the deadlocking

plunger cannot enter the strike aperture alongside the latchbolt when the door is closed.



CC-CL50-v1:0218



Keywords: Lock Locks Code CodeLock CodeLocks Program Programming Instruction Instruct Help

Support Troubleshoot Troubleshooting Sequence Sequences Install Installation Parameters Settings

Setting Parameter Setting Set up Mechanical CL CL50 50

Tabla de contenidos

Otros manuales de Cerrar de CODELOCKS

CODELOCKS

CODELOCKS KL1000 G3 NetCode Manual de usuario

CODELOCKS

CODELOCKS CL4500 Manual de usuario

CODELOCKS

CODELOCKS CL500 Manual de usuario

CODELOCKS

CODELOCKS CL4510 Manual de usuario

CODELOCKS

CODELOCKS CL5500 SERIES Manual de usuario

CODELOCKS

CODELOCKS CL1000 Manual de usuario

CODELOCKS

CODELOCKS CL600 Manual de usuario

CODELOCKS

CODELOCKS CL300 Manual de usuario

CODELOCKS

CODELOCKS CL250 Guía del administrador

CODELOCKS

CODELOCKS CL1200 Manual de usuario

CODELOCKS

CODELOCKS KL1050 Manual de usuario

CODELOCKS

CODELOCKS CL400 Manual de usuario

CODELOCKS

CODELOCKS CL5000 Manual de usuario

CODELOCKS

CODELOCKS Pushbutton 500 Series Guía de inicio rápido

CODELOCKS

CODELOCKS CL6010 Manual de usuario

CODELOCKS

CODELOCKS KL1050 C2 Manual de usuario

CODELOCKS

CODELOCKS CL5510 Manual de usuario

CODELOCKS

CODELOCKS CL210 Manual de usuario

CODELOCKS

CODELOCKS KitLock Slam Latch Manual de usuario

CODELOCKS

CODELOCKS CL5020 Manual de usuario

CODELOCKS

CODELOCKS Kit-Lock KL1100 Manual de usuario

CODELOCKS

CODELOCKS NANO90 Manual de usuario

CODELOCKS

CODELOCKS CL100 Manual de usuario

CODELOCKS

CODELOCKS 4000 Series Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario