CNC Solutions DOOR MATE Manual de usuario
MANUAL
DOOR MATE
cnc automatic door system
Dear Customer,
Thank you for purchasing your Door Mate CNC automatic door system
from CNC Solutions llc. This manual contains all the important information
regarding safety, installation, usage and care of the Door Mate.
Please review and understand this manual before you get started with cnc
automatic door opener. If you have any questions, please send email
Sincerely,
The team of CNC Solutions LLC
CNC Solutions LLC
260 Grell Lane
Johnson Creek, WI 53038 USA
Phone: 888-392-8970
E-mail [email protected]
Website www.cncsolutionsllc.com
DOOR MATE
cnc automatic door system
INDEX
1
1-1
1-2
1-3
1-4
1-5
2
2-1
2-2
2-3
2-4
2-5
2-6
3
3-1
OVERVIEW
Safetyf rst
Warning
Designed intent
Limited Liability
Overview
Attaching to CNC Machine
Preparation
Mounting
Installing the Door Mate
Adjusting the Door Mate
Door Mate Set up Programming
Troubleshooting
MAINTENANCE
Maintenance overview
DOOR MATE
cnc automatic door system
1 OVERVIEW
1-1 SAFETY FIRST
Below are the safety symbols used in this manual:
1-2 Scope
This symbol is shown to avoid a serious injury or serious damage to
the CNC automatic door system and/or the cnc machine may occur if
the instruction is not followed properly
This symbol is shown to bring extra attention to the explanation, but
that there is no immediate danger for damage or injury
This symbol is shown to avoid a serious injury or serious damage to
the CNC automatic door system and/or the cnc machine may occur if
the instruction is not followed properly
Installation of the cnc automatic door system will change how the
safetyofthedooristted.ThesafetyoftheCNCMachineshouldbe
reevaluated with a safety risk assessment.
DOOR MATE
cnc automatic door system
1-3 DESIGN INTENT
1-4 Limited liability
The cnc automatic door system is an after-market product to an existing CNC machine.
TheautomaticopeningandclosingoftheCNCmachinedoorwaywillallowyoutoll
and remove parts from the CNC machine ergonomically and with Automation using
Robots.
CNC Solutions llc accepts no liability for damage by:
• Failure to comply with these operating instructions.
• Unintended use.
•Maintenancebyunqualiedpersonnel.
•Unauthorizedmodications.
• Technical changes.
• Use of spare parts not recommended by the manufacturer
DOOR MATE
cnc automatic door system
1-5Overview
Complete Door Mate Assembly
Exploded Door Mate Assembly View
DOOR MATE
cnc automatic door system
2 Attaching to CNC machine
2-1 Preparation
Inspect the Door mate upon delivery for any damages.
Tools Needed:
6mm Allen Wrench
9mm Drill bit
Pencil
Parts included in Kit:
Belt
Electrical Enclosure
Cable / Wire
Checkthatthereissucientstabilityaroundthe
CNC machine to enable a safe installation.
The installation of the automatic door opener
shouldbeperformedbyqualiedpersonnelof
the customer or appointed by the customer.
DOOR MATE
cnc automatic door system
2-2 Mounting on the CNC machine
The top covers need to be removed.
There are (10) 8mm x 1.25 BHCS screws and washers.
A 6mm Allen wrench is also needed to perform this task.
FIG. 2.2-2
FIG. 2.2-1
DOOR MATE
cnc automatic door system
2-3 Installing the Door Mate
Remove machine backing plate with threaded
holes from Door Mate brackets.
Shown in FIG 2.2-3
Place unit on top of machine and mark hole
pattern on the top of the door.
FIG. 2.3-2
FIG. 2.3-1
Remove machine threaded backing plate from
Door Mate brackets.
Shown in FIG 2.3-2
Place unit on top of machine and mark hole
patten on the top of the door to be installed to.
DOOR MATE
cnc automatic door system
Motor connection location
Installing the Electrical Box
Distance from the Electrical box must
not exceed 5 Meters.
Mount using hardware provided
(attached to box)
Place on top of machine or on the
side of the machine within the correct
distance for the legnth of the cable.
2-3 Installing the Door Mate
Tabla de contenidos
