CNB LXC1050IR Manual de usuario

LXC1050IR

Network

eatherproof

Camera

Rev.1.1 (Sep. 2014) 2

Caution

Any changes or modifications in construction of this device which are not explicitly

approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generate, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into and outlet on a circuit different from that to which

the receiver is connected

 Consult the dealer or an experienced radio/TV technician for help.

Directions

Be careful not to cause any physical damage by dropping or throwing LXC1050IR. Especially

keep the device out of reach from children.

Do not disassemble LXC1050IR. No After Service is assumed when disassembled.

Use only the power adapter provided with LXC1050IR.

Be careful to prevent moisture or water penetration into the unit. Particular attention is

needed when installing LXC1050IR. The screw holes for the installation screws and pipe

should be maintained water tight during the whole life time of the product.

All the electrical connection wires running into the unit should be prepared so that water from

the outside cannot flow into the unit through the surface of the wires. Penetration of the

moisture through the wire for extended period can cause malfunction of the unit or

deteriorated image.

Rev.1.1 (Sep. 2014) 3

Contents

1. Introduction .............................................................................................................................................. 4

1.1. Overview ............................................................................................................................................. 4

1.2. Specification ........................................................................................................................................ 5

1.3. Applications of LXC1050IR .................................................................................................................. 6

2. Product Description ................................................................................................................................. 7

2.1. Contents ............................................................................................................................................. 7

2.2. Product Preview .................................................................................................................................. 7

2.3. Physical description............................................................................................................................. 8

2.3.1. External View ............................................................................................................................ 8

2.3.2. Dimension ................................................................................................................................. 8

2.3.3. External Connector .................................................................................................................... 9

2.3.4. BRACKET ASS’Y .................................................................................................................... 10

3. On Site Installation ................................................................................................................................. 11

4. Getting Started ....................................................................................................................................... 12

4.1. PC Requirement................................................................................................................................ 12

4.2. Quick Installation Guide ..................................................................................................................... 12

4.2.1. Connect PC and LXC1050IR to network. ................................................................................. 12

4.2.2. Install IP installer and set IP parameters on LXC1050IR .......................................................... 13

4.2.3. Remote video connection to LXC1050IR ................................................................................. 16

4.2.4. Additional settings through connection to the Admin Page ....................................................... 17

5. Trouble Shooting ................................................................................................................................... 18

5.1. No power is applied ........................................................................................................................... 18

5.2. Cannot connect to the Video ............................................................................................................. 19

5.3. Windows Vista or Windows 7............................................................................................................. 20

5.4. Technical Assistance ......................................................................................................................... 23

Rev.1.1 (Sep. 2014) 4

1. Introduction

1.1. Overview

LXC1050IR is multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and

hardware technology. It enables real time transmission of video of up to 1080P. Remote clients can connect to

LXC1050IR for the real time video data through various client solutions running on PC or smart device.

LXC1050IR is specialized in video transmission which economic and practical products removing sensor, replay,

etc and the videos can be only available in the field and place where needed.

Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the owner to reduce TCO (Total Cost of

Ownership) by reducing on-site wiring works for the installation.

Rev.1.1 (Sep. 2014) 5

1.2. Specification

Camera

Image sensor Progressive scan 1/2.9 inch CMOS 2.0M pixels

Full resolution 1,920 x 1,080 pixels (Full HD)

Min. illumination 0.2Lux (Color, DSS On), 0.00 Lux (IR LED On)

S/N Ratio 50dB or more

White Balance Auto

DSS Supported

WDR Off/ON

Lens Built-in Fixed Mega Pixel Lens, f=4mm, F2.0

Day & Night ICR(CDS Type)

IR LED 24EA(850nm, 45°) Max. 20m

Video

Compression method Simultaneous Dual Codec (H.264 / MJPEG)

Resolution 1920x1080@30fps

Multi-Profile Streaming - 3 simultaneous video profiles

- Select the codec type, resolution and frame rates for each profile.

Intelligent Bit-Rate Control Hybrid Bit Rate control (VBR+CBR)

Image Setting Text overlay, Privacy mask

Motion detection 3 regions

Network

Network Protocol

- IPv4/v6, TCP, UDP, IGMP, ICMP, ICMPv6, ARP, RARP, PPPoE, RTCP

- RTP, RTSP, SDP, HTTP, HTTPS, SMTP, FTP, DHCP, UPnP

- NTP, DNS, DynDNS, SOCKS

Dynamic IP Supported (through management server)

Security - User ID & Password protection, IP address filtering

- HTTPS encryption, Digest Authentication, User Access Log

Streaming method

- RTSP streaming with proprietary format for control informations

- Standard RTSP streaming

- HTTP streaming

External Terminals

LAN 10/100BaseT LAN

Power DC 12V input

Factory Reset Supported

Rev.1.1 (Sep. 2014) 6

Alternate Power

Standard PoE IEEE802.3af Supported

Alarm & Event

Intelligent Video Motion Detection

Alarm Triggers Intelligent Video

Alarm Events Video file upload(FTP), Still Image(Email)

Alarm Buffer (Video) configurable Pre-alarm (5~10 sec) & Post-alarm (10~30 sec)

Client Software

NVR2 64ch@D1 (free of charge)

Mobile App. Android, iOS (free of charge)

Miscellaneous

Operating Temperature -10



C~50



Operation Humidity 8~80% RH

Power DC 12V, Max 5W

Dimensions(W x H x D) 62mm(2.44”) x 62mm(2.44”) x 124.3mm (4.89”)

Weight Camera : 375g, Bracket : 55g

Casing ABS, White

Approvals FCC, CE, KCC, RoHS

Package information IP camera, CD (User’s guide, Software…)

Optional Items

Adapter DC 12V, 2A

1.3. Applications of LXC1050IR

 Small Office, Home environment, Personal user.

 Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,

military, etc.)

 Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)

 Weather and environmental observation

Rev.1.1 (Sep. 2014) 7

2. Product Description

2.1. Contents

The product package contains followings :

Contents Description Remarks

LXC1050IR IP camera LXC1050IR main unit

Accessories Screws (3 pieces of 1 type),

L-type wrench 1EA

CD Software & User’s Guide

Bracket Bracket

2.2. Product Preview

LXC1050IR IP-Installer CMS Software (NVR2)

IP Camera PC software to allocate an IP

address to the IP Camera

PC software to view and record the

streaming data transmitted from IP

camera.

(Simultaneous support of up to 64

IP cameras@D1)

Rev.1.1 (Sep. 2014) 8

2.3. Physical description

Figure 2-1. External view of LXC1050IR

Figure 2-2. Dimension

Unit : mm

Rev.1.1 (Sep. 2014) 9

Figure 2-3. Connector for external connection

 Power : Power input for supplying 12V DC power.

Caution : If LXC1050IR is powered by PoE, do not plug in DC Jack with active DC

power into DC power connector.

 Network (LAN)

100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af).

Figure 2-4. Factory Default Switch

Factory Default Switch

NETWORK (LAN)

Power

Rev.1.1 (Sep. 2014) 10

 Factory Default Switch

Factory default switch is provided for returning the IP camera to factory default state. Unscrew the cover

to access the switch. Press the switch about 5 seconds while power is applied to return to factory default

state

S’

’Y

Figure 2-4. BRACKET ASS’Y

Tabla de contenidos

Otros manuales de Cámara IP de CNB

CNB

CNB AN802IR Manual de usuario

CNB

CNB MPC1070PN Manual de usuario

CNB

CNB MPC1070PN Manual de usuario

CNB

CNB S2465NX Manual de usuario

Manuales populares de Cámara IP de otras marcas

FLIR

FLIR Exx series Manual de usuario

Avigilon

Avigilon H4A-BO1-IR Manual de usuario

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manual de usuario

ShareTech

ShareTech AV1 Manual de usuario

Ezviz

Ezviz C6C Manual de usuario

Melchioni

Melchioni UCAM 2015 Manual de usuario

Geutebruck

Geutebruck G-Cam/ESD-4630 Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manual de usuario

Mitel

Mitel 6800i Series Manual de servicio

Vitek

Vitek VTC-IR403-212NP Manual de usuario

THOMSON

THOMSON DSC - 323W Manual de usuario

AVer

AVer FB2027 Manual de usuario

ENFORCER

ENFORCER EV-T5105-N2SQ Manual de usuario

Wansview

Wansview NC543 Manual de usuario

Eneo

Eneo MCB-64A0003M0A Manual de usuario

deView electronics

deView electronics CBDNI36F Manual de usuario

Swann

Swann SwannEye Manual de usuario

LevelOne

LevelOne IP CamSecure Manual de usuario