CMD Neptune Guía de solución de problemas
Neptune Installation, user and care guide
Part No: 134310 Issue No: 001
Contents
The keystone coupler
should click into place if
installed correctly.
Ensure there is sufcient
space under the desk
to accommodate the
Neptune body and nut.
Ensure the aperture in
the desk is free of debris
then carefully lower the
Neptune into place.
Plug the male 3-pole
connector supplied as
standard into a female
powered connector.
Note the starter lead is
not supplied and is sold
separately.
Use an appropriate tool
to release the locking
mechanism.
With the xing nut
removed, depress the
clip on the keystone
blank to release it.
Carefully measure and
cut out the aperture in
the desk surface if not
already present.
Feed the cable through
the xing nut ready for
the Neptune to be xed
in place.
Ensure the attached
locking mechanism
clicks into place on both
connectors.
Separate the connectors.
Remove the keystone
blank and keep it in a
safe location for future
use.
Insert desired/relevant
data cables into the
keystone coupler.
Unscrew the xing
nut from the Neptune
body to allow it to pass
through the aperture.
Ensure the socket is in
the desired orientation
and secure in place by
tightening xing nut.
Insert a data keystone
coupler from the
underside (coupler
supplied separately).
The cable connector
should t securely in
place.
Mounting to desk
Connecting to power
Connecting data/AV
Dimensions
Connecting standard 3-pole connector
Disconnecting standard 3-pole connector
Manual circuit
breaker reset
(appropriate tool
required to reset)
Keystone
blank
102mm
Ø80mm
220.75mm
90mm
14.5mm
Type-A and C
USB charging
‘CLICK’
‘CLICK’
Fixing
nut
**WARNING**
The input connector
must not be engaged
or disengaged when
under load or live.
77mm
CMD Ltd, Rotherham, S65 1EN, UK
T: 01709 829 511 E: [email protected]
charging
Neptune is tted with an
integral circuit breaker
In the event of the
circuit breaker tripping,
remove the connected
plug rst.
Using an appropriate
tool, fully depress the
reset button until a click
is heard.
Resetting the circuit breaker
Additional information
• Installation is to be carried out in accordance with relevant Health & Safety regulations and only to be carried out by a skilled or competent person.
• The product should be installed to comply with the relevant national standards and be inspected and tested prior to being put into service (in the UK
BS 7671 Wiring Regulations or BS 6396 Ofce and Educational Systems Best Practice).
• Isolate the supply before installation or repositioning. Any locking mechanisms must be used and fully engaged.
• Incorrect use could lead to risk of electrocution.
• Connectors must not be engaged or disengaged when under load or live.
• Product to be used only for the intended purpose of distributing power and data in ofce and commercial environments.
• Do not misuse, dismantle or re-congure the product because doing so will invalidate the warranty.
Safety
• Refer to the Declaration of Conformity.
Standards
• Compatible wireless charged devices (i.e mobile telephones) may require protective cases removing to allow the wireless charger to function correctly.
Consult the operation manual of your compatible device for further information.
• Should the supply cable need replacing, contact CMD.
Further guidance
• Clean using a dry cloth. No abrasives or solvents to be used on the product.
• Do not drop or expose to moisture.
Product care
Place a compatible
device as shown onto
the area marked with a
battery icon.
You may need to adjust
your compatible device
to align the charging
elements.
The compatible device
should indicate that
charging has initiated
when correctly placed.
Wireless charging
Neptune is tted with
integral USB type-A
(18W max) and type-C
(65W max) chargers.
Insert type-A and type-C
USB cables into their
respective ports as
shown.
Ensure cables are
securely connected.
USB charging
‘CLICK’
Otros manuales de Cargador de baterías de CMD
