Climatisation RC4 Manual de usuario
OPERATING MANUALOPERATING MANUAL
OPERATING MANUALOPERATING MANUAL
OPERATING MANUAL
MURC4 G - 399420MURC4 G - 399420
MURC4 G - 399420MURC4 G - 399420
MURC4 G - 399420
CLIMATISATION
RR
RR
RC4C4
C4C4
C4 remote controlremote control
remote controlremote control
remote control
2
ON / OFF key
Operating mode selection key for
COOLING (except Water chiller wall
unit)
HEATING (except Water chiller wall
unit)
AUTOMATIC COOLING / HEATING REGU-
LATION,
VENTILATION,
DEHUMIDIFICATION(except Water
chiller wall unit)
I FEEL key: local detection of temperature
VENTILATION SPEED or AUTOMATIC VEN-
TILATION selection key
Ambient temperature increase key
Ambient temperature decrease key
SLEEP key
Directional vane sweeping (only wall unit
and water chiller wall unit)
Directional vane sweeping(only wall unit
and water chiller wall unit)
PROGRAMMING selection key
“+” key: increases the operating time datum
“-” key: decreases the operating time datum
Liquid crystal diode display (BACK LIGHT
OPTIONAL)
I FEEL sensor
Infrared signal transmitter
ROOM key: display of the ambient
temperature
SET key: sets the switch-on and/or switch-
off times of the PROGRAMMING FUNCTION
CLEAR key: cancels the preset parameters
of the clock
LOCK keyTouche SET
RESET FUNCTION:
1) Remove one battery
2) Simultaneously press these 4 keys until
the symbols are no longer displayed
3) Reinstall the battery
NOTE :NOTE :
NOTE :NOTE :
NOTE :
Open the cover / flap to access the con-
trol keys.
The four keys to be pressed are:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
9
4
16
1
3
2
7
8
19
6
5
17
13
14
15
10
11
12
18
3
INSTRUCTIONS FOR THE REMOTE CONTROL
OPERATION OF THE PROGRAMMING FUNCTIONS
Four different types of programming function can be selected with the remote control. Two
daily programming functions (called T1 & T2) and two optional week-end programming functions
(called WKT1 & WKT2). Each of these programming functions can be selected by pressing
the TIMER key (10). To adjust the programs, use the HOUR + key (11) and HOUR - key (12).
The SET key (17) activates the programming function, and the CLEAR key (18) cancels it.
A. DAILY PROGRAMMING
Daily programming functions T1 and T2 enable the switch-on and switch-off times to be programmed
separately over two different periods. Once it has been set, the programming function will run every
day.
B. WEEK-END PROGRAMMING (OPTIONAL)
Week-end programming functions WKT1 and WKT2 enable the switch-on and switch-off to be
programmed separately over two different periods, for two days only.
These programs will operate on the specified day and following day, for two days only.
At midnight on the second day, the WK programming function stops and the daily programming
function resumes its normal operation.
* WKT1 - Active on the specified day
* WKT2 - Active on the day after the specified day
REMARK:
1. During the operation of the week-end programming functions, the daily programming functions are
deactivated.
2. The WK programming functions must be reactivated before each week-end.
C. CHOICE OF A PROGRAMMING FUNCTION
Press the TIMER key (10) to select a programming function. Each
time the TIMER key (10) is pressed, one of the four programming
icons shown below appears on the LCD display.
1 Press the TIMER key to select daily programming function T2.
Icon 2 of Programming function T2 flashes.
2 Press the TIMER key to select daily programming function T2.
Icon 2 of Programming function T2 flashes.
3 Press the TIMER key to select week-end programming function
WKT1.
Icons 1 and WK flash.
4 Press the TIMER key to select week-end programming function
WKT2.
Icons 2 and WK flash.
4
ADJUSTMENT OF THE SWITCH-ON TIME
After selecting a programming function (T1, T2 or WKT1, WKT2),
proceed as follows to adjust the programmed switch-on time.
EXAMPLE: Air conditioner switch-on at 10:30 (a.m.)
1 Press the SET key
The ON (switch-on) icon and the switch-on time flash.
2 Adjust the hour and minutes.
1. Set the switch-on time to 10:30
2. Press the HOUR + key to increase the time or the HOUR - key to
decrease it.
3 Press the SET key.
1. The switch-on time is programmed for 10:30 (a.m.) (the “ON”
[Switch-on] icon comes on steadily).
2. The “OFF” [Switch-off] icon and the switch-off time flash.
4 Press the CLEAR key.
The programmed switch-off is no longer displayed.
REMARKS:REMARKS:
REMARKS:REMARKS:
REMARKS:
1. The implicit settings of the programming functions are 7:00 and
18:00 (7 a.m. and 6 p.m.) for the switch-on and switch-off times.
2. The programming mode will always display the last switch-on and
switch-off (ON and OFF) settings on the LCD display.
5
ADJUSTMENT OF THE SWITCH-OFF TIME
After selecting a programming function (T1, T2 or WKT1, WKT2),
proceed as follows to adjust the programmed switch-off time.
EXAMPLE: Air conditioner switch-off at 18:30 (6:30 p.m.)
1 Press the SET key
The ON (switch-on) icon and the switch-on time flash.
2 Press the CLEAR key.
1. The programmed switch-on is no longer displayed.
2. The “OFF” (Switch-off) icon and the switch-off time flash.
3 Adjust the hour and minutes.
1. Set the switch-off time to 18:30 (6:30 p.m.)
2. Press the HOUR + key to increase the time or the HOUR - key to
decrease it.
4 Press the SET key.
1. The switch-off time is programmed for 18:30 (6:30 p.m.) (the
“OFF” icon of the programming function comes on steadily).
REMARKS:REMARKS:
REMARKS:REMARKS:
REMARKS:
1. The implicit settings of the programming functions are 7:00 and
18:00 (7 a.m. and 6 p.m.) for the switch-on and switch-off times.
2. The programming mode will always display the last switch-on and
switch-off settings on the LCD display.
6
ADJUSTMENT OF THE SWITCH-ON AND SWITCH-OFF
TIMES
After selecting a programming function (T1, T2 or WKT1, WKT2),
proceed as follows to adjust the programmed switch-on and
switch-off times.
EXAMPLE: Air conditioner switch-on at 10:30 (a.m.) and switch-
off at 18:30 (6:30 p.m.)
1 Press the SET key
The ON (switch-on) icon and the switch-on time flash.
2 Adjust the hour and minutes.
1. Set the switch-on time (ON) to 10:30
2. Press the HOUR + key to increase the time or the HOUR - key to
decrease it.
3 Press the SET key.
1. The switch-on time is programmed for 10:30 (a.m.) (the ON icon
flashes2).
2. The “OFF” (Switch-off) icon and the switch-off time flash.
4 Adjust the hour and minutes.
1. Set the switch-off time (OFF) to 18:30 (6:30 p.m.)
2. Press the HOUR + key to increase the time or the HOUR - key to
decrease it.
5 Press the SET key.
The switch-off time is programmed for 18:30 (6:30 p.m.) (the “OFF”
icon of the programming function comes on steadily).
REMARKS:REMARKS:
REMARKS:REMARKS:
REMARKS:
1. The implicit settings of the programming functions are 7:00 and
18:00 (7 a.m. and 6 p.m.) for the switch-on and switch-off times.
2. The programming mode will always display the last switch-on and
switch-off settings on the LCD display.
3. Pressing the CLEAR key (18) for 5 seconds cancels all the
programming function settings and erases the display of the
programming.
7
TO CHANGE THE PRESET TIMES
Example: To change the switch-on time from 10:30 (a.m.) to 9:20 (a.m.)
(without changing the switch-off time).
1 Press the TIMER key until the icon of the selected programming
function flashes.
REMARK: the times already programmed into the corresponding
programming function are displayed without flashing.
2 Press the SET key to enter the edit mode.
The ON (Switch-on) icon and the switch-on time flash.
3 Change the time to 9:20 (a.m.) by pressing the HOUR - key.
The ON icon and the switch-on time flash.
4 Press the SET key to save the new setting.
The ON icon and the switch-on time come on steadily, and the
“OFF” (Switch-off) icon and the switch-off time flash.
5 Press the SET key to confirm the previous setting of the switch-off
time.
The ON and OFF icons and the corresponding programmed times
come on steadily.
8
TO CANCEL THE TIME SETTING OF A SPECIFIC PROGRAMMING
FUNCTION
To cancel the switch-on time whilst retaining the previously set switch-
off time.
1 Press the TIMER key to select the required programming function.
The selected programming function icon flashes and the
corresponding previously programmed switch-on and switch-off
times come on steadily.
2 Press the SET key to enter the edit mode.
The ON (Switch-on) icon and the switch-on time flash.
3 Press the CLEAR key
The switch-on time is cleared. The OFF (Switch-off) icon and the
switch-off time flash.
4 Press the SET key
This confirms the new setting
TO CANCEL THE SWITCH-OFF TIME WHILST RETAINING THE
PREVIOUSLY SET SWITCH-ON TIME.
1 Press the TIMER key to select the required programming function.
The selected programming function flashes and the corresponding
previously programmed switch-on and switch-off times come on
steadily.
2 Press the SET key.
The ON icon and the switch-on time flash.
3 Press the SET key.
The ON icon and the switch-on time come on steadily.
The OFF icon and the switch-off time flash.
4 Press the CLEAR key
The switch-off time is cleared.
9
TO CANCEL THE SWITCH-ON AND SWITCH-OFF SETTINGS.
1 Press the TIMER key to select the required programming function.
The selected programming function icon flashes and the corresponding
previously programmed switch-on and switch-off times come on
steadily.
2 Press the CLEAR key
All the settings in the selected programming function are cleared.
NIGHT SLOW (SLEEP) FUNCTIONNIGHT SLOW (SLEEP) FUNCTION
NIGHT SLOW (SLEEP) FUNCTIONNIGHT SLOW (SLEEP) FUNCTION
NIGHT SLOW (SLEEP) FUNCTION
Press the SLEEP key (7) to select the night slow function.
The night slow icon and the implicit night slow termination time icon (7
hours after the current time) flash.
The implicit setting can be set to any value between 3 hours and 12
hours, by pressing the HOUR + key (11) or the HOUR - key (12).
(The initial value displayed by the SLEEP clock is either the implicit
value or the selected value, plus the current time).
Example: It is currently 23:00 (11 p.m.) and the sleep mode is selected.
The sleep mode termination time will implicitly be 6:00 (6 a.m.) If the
sleep mode value is set to 10 hours, the sleep mode termination
time will be 9:00 (9 a.m.).
10
Tabla de contenidos
Idiomas:
