Clevertronics Argonaut PRO ARGOPRO-1200 Series Instrucciones de instalación y funcionamiento

1948882

V1.2

28 February 2022

THIS PAGE IS INTENTIONALLY LEFT BLANK

240V Argonaut PRO Weatherproof LED Batten

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

UK OFFICE

Website: www.clevertronics.co.uk

362 Stockley Close

West Drayton UB7 9BL

Phone: 01895 430 255

Models: ARGOPRO-1200-xx-yy

Options:

Microwave Sensor (HI/LO)

xx = SEN

DALI Driver

xx = DD

ZW Inline Filter

yy = FLT

Spare Parts:

8002755

PCA:LED Strip ARGOPRO-1200,HT10540-A1,16P16S,4000K

1330055

LED Driver –Tridonic LC 50w 350-1050mA, 20-50V

1330151

LED Driver - TCI DC MAXI JOLLY SVM 65 DALI SLIM

(SEN version only)

1330056

LED Driver –Tridonic LCA 50w 350-1050mA, one4all Ip PRE

(DD version only)

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Building and Electrical Standards.

1948882

V1.2

28 February 2022

Installation:

This product can be mounted/suspended from any solid surface. Follow the below installation steps:

•Determine the installation and power entry method.

•Undo the Diffuser Clips, remove the Diffuser and Gear Tray. Position the batten base in the desired

location and Mark out the fixing points on the mounting surface.

•If the cable entry is to be via the rear of the body –Drill out a suitable entry-hole in the rear of the

batten body (must be suitably sealed after cable entry using a sealant). If the cable entry is via the

end of the batten - Install the provided cable gland, or bring in conduit, to the base as required for

the intended power access.

Note: Only round cables are to be used with the cable gland for an IP65 seal. Keep cable entry

straight and tension free. Ensure all seals are tight.

min. wire diameter 7mm, max. 12mm.

•For surface mounting, there are 3 extrusions/posts at each end of the base. Drill out the desired

number of fixing points at each end. Fixings must only be through the extrusions/mounting

posts.

oPosition the fitting to the mounting surface and mark the mounting holes.

oCable/Gland entry to be down if mounting vertically.

oDrill the mounting holes.

oFix the base to the surface with appropriate fixings.

oSeal any penetrations/fixing points with appropriate sealant.

•For Surface Mount Clip mounting, measure/mark spacing (see Dimensions image), install

stainless steel clips to surface (use appropriate fixings), then insert batten into clips.

•For Suspension Mounting, measure/mark spacing (see Dimensions image), install suspension

device, E.G chain, and connect chain to batten base.

•Wire mains power cable, 240V 50Hz, to terminals marked L, N & (and DALI Cable to terminals

marked Da Da as applicable)

•Set Switch to the desired Lumen Output (3541lm | 4660lm | 5495lm | 6259lm, Default = 4660lm)

•Attach Gear Tray to lanyards.

•Reinstall the Gear Tray.

•Reinstall the Diffuser, latch the Diffuser using Diffuser Clips and secure with screws provided

NOTE:

•This luminaire (with reinforced insulation between control/LED terminal and AC Supply) contains

non-user replaceable light source –to be replaced (if required) by the manufacturer or his service

agent or a similar qualified person.

Dimensions:

Lumen Setting:

For -SEN products refer to the DIP Switches on

the Driver.

NOTE: Recommended currents are 500mA, 650mA, 750mA & 900mA for this product. Using settings

outside of the recommended will void warranty. Product must be de-energised before switching

Lumen/Current.

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The LED Strip is not illuminated.

Check: A.C. is connected and is turned on.

Wiring connections between the LED Driver & LED Strips

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

https://clevertronics.co.uk/product-warranty-statement/

Otros manuales de Linterna de Clevertronics

Clevertronics

Clevertronics L10 LIFELIGHT PRO Manual

Clevertronics

Clevertronics ARGO-600 EM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO-SMC Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Supalite CFLLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Argonaut Square ARGOSQ Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP LIFELIGHT CLIFE Series Guía de mantenimiento y servicio

Clevertronics

Clevertronics LP CBS2N Series Especificaciones técnicas

Clevertronics

Clevertronics L10 LIFELIGHT PRO-SM Series Manual de usuario

Clevertronics

Clevertronics ARGO-1500-EM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Supalite LWFLED Series Manual de instrucciones

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO-SMC Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Supalite CFLLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Supalite L10 LWFLED Series Especificaciones técnicas

Clevertronics

Clevertronics L10 LWP2LIFE-PRO-WPPOD Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LWFLED Guía de mantenimiento y servicio

Manuales populares de Linterna de otras marcas

KYOWA

KYOWA KW-9114 Manual de usuario

Stahl

Stahl ECOLUX 6610 Series Manual de usuario

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manual de usuario

PRG

PRG VARI LITE VL5 Manual de usuario

Raytec

Raytec VARIO2 series Manual de usuario

ENSA

ENSA LEDBT18WS2 Manual de usuario

LUG

LUG OFFICE LB LED N/T Manual de usuario

GE Wallighter 250 Manual de usuario

Draper

Draper RLEDL19/B Manual de usuario

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manual de usuario

Panasonic

Panasonic EY3741B57 Manual de usuario

Clas Ohlson

Clas Ohlson LCC8T Manual de usuario

Coolon

Coolon WDN-140 Manual de usuario

Holiday Travel

Holiday Travel 834873 Manual de usuario

BEGA

BEGA 84 036 Manual de usuario

BEGA

BEGA 33 596 Manual de usuario

Dale Tiffany

Dale Tiffany GT701162 Manual de usuario

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manual de usuario