ClearView HD Cube Network Camera Manual de usuario
HD Cube Network Camera Quick Start Guide
Version 1.0.1
i
Welcome
Thank you for purchasing our network camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Before your operation please read the following instructions carefully.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1. This series product supports PoE too. Please note:
Do not connect these two power supplying sources to the device at the same time; it may result
in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
ii
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name Amount
Network Camera 1
Quick Start Guide 1
Installation Accessories Bag 1
CD 1
iii
Table of Contents
1Structure ......................................................................................................................................1
1.1 Device Components.....................................................................................................1
1.2 Dimensions....................................................................................................................2
1.3 Bidirectional talk ...........................................................................................................3
1.3.1 Device-end to PC-end ..........................................................................................3
1.3.2 PC-end to the Device-end....................................................................................3
1.4 Alarm Setup...................................................................................................................4
1.4.1 Alarm Input and Output Connection...................................................................4
2Device Installation ......................................................................................................................6
3Quick Configuration Tool...........................................................................................................8
3.1 Overview........................................................................................................................8
3.2 Operation .......................................................................................................................8
4Web Operation..........................................................................................................................11
4.1 Network Connection...................................................................................................11
4.2 Login and Logout........................................................................................................11
5FAQ ............................................................................................................................................14
Appendix Toxic or Hazardous Materials or Elements ...............................................................16
1
1Structure
1.1 Device Components
You can refer to the following figure for component information. See Figure 1-1.
Figure 1-1
Please refer to the following sheet for detailed information.
SN Port Name Indicator Connector Note
1 Power indicator
light POWER /
zWhen system boots up–Green
light becomes on.
zWhen system is upgrading –
Green light flashes. Interval is
0.5s.
zWhen system is alarming–
Green light flashes. Interval is
0.2s.
2 Network
indicator light NET /
zWire network connection-Red
light is on.
zWireless network connection-
Green light is on.
3 Speaker / /
Output audio signal.
(This function is optional. For some
series product only.)
4 White light / /
Can activate motion detect, PIR
human body movement detect,
external alarm.
2
SN Port Name Indicator Connector Note
5 PIR sensor PIR /
Passive IR motion detect port. It
can detect the IR object movement
(such as human body or other
heating object).
6 Microphone / /
Directly receive audio signal.
(This function is optional. For some
series product only.).
7 Micro SD card Micro SD Micro SD
card slot
SD card storage.
(This function is optional. For some
series product only.).
8 Reset button Reset /
Restore factory default setup.
When system is running normally,
press the RESET button for at least
5 seconds, system can restore
factory default setup.
9 WPS button WPS Fast wireless
connection
Press the WPS button of the router
and the device respectively for at
least 2 seconds. Usually the device
can connect to the router within 1
minute.
Please note it is for wireless
series product only and it is for
the wireless router of the WPS
function.
10 Alarm pin / I/O port
Alarm signal input/output
(This function is optional. For some
series product only.).
11 Power port DC12V / Input DC 12V power.
12 Network port LAN Ethernet port
zConnect to standard Ethernet
cable.
zSupport PoE function.
1.2 Dimensions
Please refer to the following figure for dimension information. The unit is mm. See Figure 1-2.
3
Figure 1-2
1.3 Bidirectional talk
1.3.1 Device-end to PC-end
Device Connection
Please connect the speaker or the MIC to the audio input port in the device rear panel. Then connect
the earphone to the audio output port in the PC.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.
Listening Operation
Speak or play music at the PC-end, you can use the earphone or the sound box of the PC-end to
listen the audio information from the device-end.
1.3.2 PC-end to the Device-end
Device Connection
Connect the speaker or the MIC to the audio input port in the PC and then connect the earphone to the
audio output port of the device.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.
Listening Operation
4
Speak or play music at the PC-end, you can use the built-in speaker of the device-end to listen.
Note
Please go to the Master Volume interface of the PC to set first if you want to use the dual-way
bidirectional talk. Please select Front Mic mode in the record control interface. (You can select
microphone enhanced in Advanced interface if the audio is too low.)
1.4 Alarm Setup
The alarm setup interface is shown as below. See Figure 1-3.
Figure 1-3
1.4.1 Alarm Input and Output Connection
Please refer to the following figure for alarm input information. See Figure 1-4.
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of
the alarm input port. When the input signal is connected to the 3.3V or is idle, the device collects the
logic “1”. When the input signal is grounded, the device collects the logic “0”.
Figure 1-4
Please refer to the following figure for alarm output information. See Figure 1-5.
Port NO and Port C composes an on-off button to provide the alarm output.
This button is normal open. The button becomes off when there is an alarm output.
5
Figure 1-5
6
2Device Installation
This series camera support two installation modes: wall mount and pendant mount. See Figure 2-1
and Figure 2-2.
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.
Step 1
Paste the installation positioning map on the installation surface such as wall, ceiling or the wood.
Step 2
Dig holes in the installation surface according to the installation positioning map.
Figure 2-1
Step 3
Insert the expansion bolts from the accessories bag to the holes you just dug. If it is the wood surface
you can skip to the next step.
Step 4
Use the screws from the accessories bag to secure the device firmly.
Step 5
Connect the cable and then boot up the device.
Step 6
Loosen the adjust knob for a little bit, adjust the camera to proper surveillance position according to
your actual requirements.
Step 7
Secure the knob of the bracket to fix the camera.
Tabla de contenidos
Otros manuales de Cámara IP de ClearView
