Clearline AKC Instrucciones de uso
1
Twin Wall Installation Instructions
and
Maintenance Guide
Please read all instructions before beginning your
installation. Failure to install this system in accordance with
these instructions will invalidate the conditions of
certification and the manufacturer warranty.
2
INDEX
PRODUCT IDENTIFICATION...................... Page 2
FUELS AND APPLIANCES .......................... Page 3
GENERAL INSTALLATION REGULATIONS .... Pages 3-5
CLEARLINE AKC COMPONENTS ................. Pages 6-18
MAINTENANCE AND CHIMNEY CLEANING.... Page 19
OFFSET CHARTS........................................ Page 20
CHIMNEY HEIGHTS................................... Page 21
WARRANTY.............................................. Page 23
PRODUCT IDENTIFICATION
Clearline AKC Twin-Wall Chimney
Sizes:125mm to 200mm
Tested for compliance with BS EN1856-1:2003
No. 0099-CDP-A71-037
Product Designation: EN1856-1 T600 - N1 - W - V2-L50040 G(60)
HETAS listed for use on solid fuel applications
Outer skin 304 grade stainless steel. Inner skin 316 grade stainless
steel. Rockwool 128kg per cubic metre, 25mm thick. All seams
fully welded. Distance to combustibles 60mm.
Available in black powder coated, as well as stainless.
A COMMON CAUSE OF CHIMNEY RELATED FIRES IS THE FAILURE TO
MAINTAIN THE REQUIRED AIR GAP BETWEEN THE OUTER SURFACE OF
THE FLUE AND COMBUSTIBLE MATERIALS.
IT IS VITAL THAT THIS FLUE PIPE SHOULD BE INSTALLED WITH THE
CORRECT MINIMUM CLEARANCES AS SPECIFIED IN THESE
INSTRUCTIONS.
3
FUELS AND APPLIANCES
CLEARLINE AKC conforms to BS EN1856-1:2003 It is an all
stainless steel insulated chimney system designed to be used with
solid fuel, biomass, oil or gas, and with both condensing and non-
condensing boilers. Clearline AKC has been tested to have a
working temperature of 600°C. Chimneys installed in accordance
with these instructions will comply with British Standards.
Failure to follow the installation instructions could cause
FIRE, CARBON MONOXIDE POISONING, OR DEATH.
GENERAL INSTALLATION REGULATIONS
Chimney installation should be carried out by a competent person.
We recommend the use of HETAS approved installers for solid fuel
applications. If installation is carried out by a non HETAS registered
installer, the installation must be certified by a local Building
Control inspector. Planning permission may be required, and
reference should be made to the local Building Control Department.
VENTILATION
It is very important that sufficient air for combustion and
ventilation is provided to the room containing the appliance to
enable correct and efficient working of the appliance and chimney
system.
CARBON MONOXIDE ALARMS
A carbon monoxide alarm must be provided in the room where the
solid fuel or gas appliance is located.
All chimney installations should comply with Document J of
Building Regulations.
https://www.gov.uk/government/uploads/system/uploads/att
achment_data/file/468872/ADJ_LOCKED.pdf
The Clearline AKC Chimney requires a 60mm clearance
to combustible material including timber joists, dry wall,
plaster and plywood.
4
Clearline AKC is an open-ended system, each component
secured with a locking band which is included with flue lengths
and elbows.
There should be no more than 4 bends in a system. (A 90°
Tee on the back of the stove counts as 2 bends). If four bends
are used there should be sweeping access between the two
offsets.
There should be no flue joins between a floor or ceiling joists
or rafters, with at least 150mm twin-wall flue projecting below
and above before an additional connection with twin wall.
The flue must not go more than 45° off vertical.
The minimum recommended height from top of stove to
termination is 4.5metres, however many stoves will run on a
shorter flue.
The minimum flue size for non defra approved stoves is
150mm.
The flue size must NEVER be smaller than the appliance
outlet, unless approved by stove manufacturer.
Flue needs to switch from single skin to twin wall at 425mm
below a ceiling.
Where the chimney passes through any part of the building,
(with the exception of the room where the appliance is
installed), where there is a risk of accidental human contact,
i.e a bedroom etc., or where there is a risk of contact with
combustible materials, the chimney must be enclosed in an
appropriate way to meet Building Regulations. This can be
achieved by boxing-in the chimney, or by the use of a
protective wire mesh frame in roof spaces etc. The minimum
distance of 60mm to any combustible material, including loft
insulation should always be observed and any enclosure
should be ventilated using the appropriate ventilated fire
stops.
Twin wall should also be boxed-in in attic spaces. This can be
achieved with wire mesh to a minimum of 1200mm in height.
Single skin flue should be 3 times its diameter from
combustible material if not heat shielded. (i.e. 150mm pipe
should be 450mm from combustible materials).
It is recommended that the maximum horizontal offset should
not exceed 20% of the total length of the chimney.
All offsets should be supported above and below with the
appropriate support component i.e. ceiling, joist, wall or roof
support.
5
It is recommended that a vertical run of at least 600mm
should be allowed immediately above the appliance prior to
any change of direction.
NOTICE PLATE
The Notice plate for Clearline AKC should be marked up in indelible
ink and securely fixed in an unobtrusive but obvious position within
the building such as:
• Next to the electricity meter
• Next to the chimney installation
• Next to the water supply stop-cock
Typical internal flue system
Typical external flue system
6
CLEARLINE AKC COMPONENTS
*** Denotes flue diameter ie: 150mm = 10-150-001
Please be aware that not ALL components are available in Black, such as
components that are normally concealed.
STARTING COMPONENTS
SW-TW ADAPTOR Code:10-***-001
Tapered adaptor for connecting to traditional stoves with a flue collar, or going
from single skin to twin wall, same diameter. Eg. 150mm single skin to
150mm twin wall. Working length 128mm.
SW-TW 100-125 INCREASING ADAPTOR Code:10-100-002
100mm single skin to 125mm twin wall.
SW-TW INCREASING ADAPTOR Code:10-125-002
Eg: 125mm single skin to 150mm twin wall.
SW-TW FLAT ADAPTOR Code: 10-***-005
Eg: for contemporary, European stoves, like Westfire, Opus, stoves without a
flue collar.
SW-TW FLAT INCREASING ADAPTOR Code:10-125-009
Eg: For connecting directly from 125mm outlet on European stove (without a
flue collar) to 150mm twin wall.
7
ADAPTOR TO FLEX Code:10-***-099
Used to convert from Twin wall insulated flue beneath, to flexible liner above.
Includes a locking band.
ADAPTOR FROM FLEX Code:10-***-101
Used to convert from Flexible liner beneath, to Twin wall insulated flue above.
FLUE LENGTHS
All flue lengths include a locking band.
1000MM LENGTH Code:10-***-010
Working length 957mm
500MM LENGTH Code:10-***-011
Working length 457mm
250MM LENGTH Code:10-***-012
Working length 207mm
100MM LENGTH Code:10-***-018
Working length 100mm
8
1000MM CONNECTING STARTER LENGTH Code:10-***-021
Working length 957mm –with integrated adaptor. This length allows the
Clearline Single Skin flue to socket up into the section by 325mm, then back
down to connect to the stove. This part allows the stove to be removed later
without dismantling the chimney system, so as to comply with building
regulations.
500MM CONNECTING STARTER LENGTH Code:10-***-022
Working length 457mm –with integrated adaptor
500-880MM ADJUSTABLE LENGTH Code:10-***-014
Adjustable lengths come with two locking bands –distance to combustibles
remains at 60mm, the same as all standard lengths.
Each adjustable length comes with an extra short length of rockwool which
gets compressed to ensure insulation continues throughout. Care must be
taken to ensure that when assembled to required length no air gaps are left.
There is a high-temp plastic seal in the adjustable length locking band to avoid
any movement once length has been adjusted to required height. The locking
band fits onto the lower lip of the pipe.
350-500MM ADJUSTABLE LENGTH Code:10-***-015
250-350MM ADJUSTABLE LENGTH Code:10-***-016
9
500MM TESTING LENGTH Code:10-***-019
Working length 457mm, including analysis port
PELLET GASKET Code:15-***-102
A rubber seal used on condensing installations to stop the condensates from
penetrating the flue.
BENDS AND TEES
All bends and Tees are fully welded on the inside and outside and come with a
locking band. Please note - Flue pipe bends are measured in degrees from the
vertical plane. Roof pitches are also measured in degrees, but from the
horizontal plane. Ie, a 30 degree flue bend will not follow a 30 degree roof
pitch.
135 DEGREE TEE Code:10-***-034
Used when exiting a wall at 45 degrees, allowing sweeping access to the
external part of the flue system.Tee Cap has to be ordered separately. Two
locking bands are included.
10
90 DEGREE TEE Code:10-***-035
When using the rear outlet on a stove. Tee Cap has to be ordered separately.
TEE CAP Code:15-***-036
Used with 90 Degree and 135 Degee Tees
TEE CAP WITH DRAIN Code:15-***-037
For condensing systems.
45 DEGREE BEND Code:10-***-031
30 DEGREE BEND Code:10-***-032
Otros manuales para AKC
1
Tabla de contenidos
Manuales populares de Cocina de otras marcas
Vermont Castings
Vermont Castings Intrepid 2 Manual de usuario
Italiana Camini
Italiana Camini CLASSICA Guía de inicio rápido
Avalon
Avalon Vashon Avanti DVS FS Manual de usuario
Spartherm
Spartherm ambiente a1 Manual de usuario
Dimplex
Dimplex MCFSTV12AU Manual de usuario
Warmlite
Warmlite WL46040 Manual de usuario