Clas Ohlson D6004CK Manual de usuario
Digital Video Recorder
Digital Videoinspelare DVR
Digital Videospiller DVR
Digitaalinen videotallennin DVR
EnglishSvenskaNorskSuomi
Art.no. Model
36-3777 D6004CK Ver. 201007
2
3
English
Digital Video Recorder
Art.no. 36-3777 Model D6004CK
Please read the entire instruction manual before use and save it for future reference. We reserve the right for any
errors in text or images and for making any necessary technical changes to this document. If you should have
any questions concerning technical problems please contact our Customer Services.
1. Description
• MPEG4 compression
• 4 channels: 4 BNC camera inputs – 2 BNC video outputs
• System format: NTSC/PAL
• Motion detector with settings for area and sensitivity
• Time scheduled, alarm, or motion detection recording modes
• Support for hard disks up to 1 TB (SATA)
• Supports PTZ control via Port 485
• Monitors and controls equipment over the Internet (broadband connection required)
• Built-in USB 2.0 port for computer back-up or to a USB flash drive
1.1 Safety
• The DVR is only intended for indoor use. Do not expose it to moisture.
• Only use the included adaptor (12 V, 5 A, + centre pin).
• The cameras are waterproof, however they should be mounted in as protective environment as possible.
• Be extra careful with the cable connections for the camera. These must be protected against moisture
penetration since they are exposed and offer no natural protection against moisture and damp.
4
English
PWR 1 2 3 4 5 6
HDD
7 8 9 0 ALL MENU
SEL
1
3
2 8 10 12
9 11 14 16 18
25
4 156 13
5 7
21 22 23 24
17
19 20
1 2 3 4 5 6 7
2. Buttons and functions
2.1 Front panel 4-channel DVR
1. Power switch
2. Hard disk lock
3. PWR LED (Power indicator)
4. [] Rewind
5. [1 ] Channel 1
6. [] Pause
7. [2 ] Channel 2
8. [] Play
9. [3 ] Channel 3
10. [] Fast forward
11. [4 ] Channel 4
12. [] Stop
13. [] Record
14. [5–9] Number 5 to Number 9
15. IR sensor
16. [] Left arrow
17. [] Up arrow
18. [] Right arrow
19. Hard disk drawer and USB connection
(Inside the cover)
20. HDD LED
21. [0] Mute (temporarily turns off volume)
22. [ ] Displays all cameras
23. [MENU] Exits the menu
24. [] Down arrow
25. [SEL] Select
2.2 Back panel 4-channel DVR
1. LAN – Network cable connection
2. Audio output
3. Audio input
4. Video output (BNC)
5. CH1 – CH 4 – Video input (BNC)
6. RS485 (PTZ input)
7. 12 V DC – Adaptor connection
5
English
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1
2.3 Remote Control
1. [1 – 9] Channel selection 1-9
2. [ALL] Displays all channels
3. [0] Number
4. [] Up arrow
5. [] Left arrow
6. [] Down arrow
7. [AUDIO/SEARCH] Audio input/output
8. [] Starts playback
9. [] Rewind
10. [] Record
11. [] Pauses playback
12. [MENU] Opens or closes the menu
13. [SEL] Selects or modifies
14. [] Right arrow
15. [MUTE] Temporarily turns off volume
16. [] Fast forward
17. [] Stops recording or playback
2.4 Contents
• Camera with protective shade and bracket (4x)
• Power adaptor
• Power adaptor splitter cable (5 to 1)
• Extension leads (4x)
• USB cable
• Bag of screws for hard disk installation
• CD
• Keys for hard disk drawer
• Remote control
• Composite video cable BNC - RCA
6
English
3. Alarm Installation
3.1 Alarm Installation
The video recorder has an internal circuit for sounding an alarm. This is normally open (NO), but closes once the
sensor is activated so that an alarm/siren (not included) sounds.
N.B. Contact a qualified tradesman for more information on an appropriate alarm and installation instructions for
purchasing an alarm that is suitable for your purposes. Two-step alarm installation:
1. Connect the positive (+) lead from the siren/alarm to the alarm port on the back panel.
2. Connect the neutral (-) lead from the siren/alarm to the power adaptor.
4. DVR system installation
4.1 Hard disk installation
N.B. Never remove the hard disk drawer when the DVR is in use. The DVR must be turned off when the hard
disk is removed otherwise the hard disk may sustain damage.
N.B. Make sure the DIP switches are set to “Master” on the hard disk before mounting. Read your hard disk
instruction manual if you are unsure.
Hard disk mounting procedure:
1. Open the front cover on the front panel (by pressing
the middle of the cover’s upper edge). Remove the hard
disk drawer.
2. Mount a SATA hard disk (Max 1 TB) into the drawer.
Secure it with the included screws.
3. Push the drawer (with the mounted
hard disk) into the opening and lock
the drawer with the drawer key.
7
English
4.2 Connecting a camera to the DVR
1. Connect the extension leads between the camera and DVR. The yellow connectors are for video and the
red connectors are for the power supply to the camera.
N.B. The BNC connectors on both ends of the extension leads are marked. The side marked “To camera
side only” should be connected to the camera and the “To DVR side only” should be connected to [CH1] –
[CH4] on the back panel of the DVR.
2. Connect the splitter cable to the power adaptor.
3. Connect the cable marked “DVR POWER” to “DC 12 V” on the back panel of the DVR. Connect the rest of
the splitter connections to the red connectors on the extension leads.
4.3 Connecting the DVR to a TV
Connect the included composite video cable to the “Video Output” connection on the back panel of the DVR
and to the “Video In” connection on your TV.
5. Starting the DVR
1. The startup screen shows the date and firmware
version used.
2. The system will attempt to detect the hard drive. Once
detected the hard disk information will be shown.
3. Once the hard disk is detected you will be asked if you wish
to format it.
• Press [SEL] to format or [MENU] to cancel.
8
English
Main Menu
Camera Setup
Record Setup
Record Frame rate
Video Quality
Record Schedule
Sensor Setup
Hard Drive Setup
Miscellaneous Setup
Network Setup
Language
Video Backup (optional)
Reset Menu
Change Password
Set Time
Hidden Channel
Audio Port Setup
PTZ Setup
Image Parameters
Password Enable
Keypad Tones
SEQ.DWELL TIME
VGA Setup
6. DVR Menus
6.1 Using the menus
• Push [MENU] to open the main menu.
• Use [] and [] to make your selection.
• Press [SEL] to modify or [MENU] to return to the previous screen or to cancel.
6.2 Menu structure
9
English
6.3 Camera Setup
Camera settings. Activate or deactivate cameras.
• Select the desired camera with [] - [] - [] -
[] and then press [SEL] to switch between ON
and OFF modes. N.B. If the camera channel is
set to OFF, the DVR will not record from it (See
6.4 Recording settings).
6.4 Record Setup
Recording settings.
• Select the desired camera with [] - [] - [] -
[] and then press [SEL] to switch between ON
and OFF modes. If the camera is set to OFF in
“Camera setup mode” the DVR will not record
that channel (camera) and “NOCAM” will be
displayed on the screen.
6.5 Record Framerate
Recording frame rate per second settings.The total
number of frames per second are 50 fps (PAL) or
60 fps (NTSC). It is possible to adjust the number
of frames per second for the selected channel
(camera). If you select a value higher than 50/60
fps the setting will automatically be adjusted to the
highest possible setting.
N.B. A higher setting will give better quality but also
take up more room on your hard disk.
• Select the desired channel (camera) with [] - []
- [] - [] and then press [SEL] to increase the
value or [STOP] to reduce the value.
6.6 Video Quality
Video quality settings.
There are 4 different settings: Highest, High,
Normal and Low.
N.B. A higher setting will give better quality but also
take up more room on your hard disk.
• Push [SEL] to change the setting.
10
English
6.7 Record Schedule
Recording schedule settings.
Scheduled recordings allow you to customise your
recording times.
Time is shown in AM/PM (12-hour clock)
• Select the desired time with [] - [] and press
[SEL] the required number of times to change the
setting between:
No-Record No recording
Normal-Record Normal recording
Sensor-Record Sensor controlled recording.
N.B. To activate recording press [] to start recording
once you see the camera image on screen. If the
recording mode is set to Normal-Record recording will
start immediately. However, if the recording mode is set
to Sensor-Record recoding will not start until activated
by the motion sensor.
6.8 Sensor Setup
Sensor settings.
Record and alarm duration settings:
• “Sensored Record Time” Selects the number
of seconds recording will progress after being
activated by the sensor. Press [SEL] to adjust the
recording time (5 – 30 seconds).
• “Alarm On Time” Selects the number of seconds
the alarm will progress after being activated by the
sensor. OFF mode (no alarm), 5 – 30 seconds,
CONT (continuous alarm. Shut off manually by
pushing any button).
6.9 H/W Sensor Setup
External sensor and alarm setup (not included).
N.B. External sensor and alarm not included. Sold
separately.
• There are 3 different settings: NOT INSTALLED,
NORMAL CLOSE (normally closed) and
NORMAL OPEN (normally open).
Tabla de contenidos
Idiomas:
Otros manuales de DVR de Clas Ohlson
