Clarke X-Pro CAT168 Manual de instalación y operación

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0417

RIGHT ANGLE SANDER

MODEL NO: CAT168

PART NO: 3120182

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Right Angle Sander.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instruction in a safe place for future reference.

SPECIFICATION

Please note that the details and specifications contained herein are correct

at the time of going to print. However CLARKE International reserve the right to

change specifications at any time without prior notice

Model Numbers CAT168

Part Number 3120182

Min. Hose Size (ID) 8 mm (5/16”)

Operating Pressure 90 psi (6.2 bar)

Air Consumption 13 cfm (max load), - 4cfm nominal

Air Inlet Size 1/4“ BSP Female

Sound Pressure Level (LpA dB) 85.8 dB(A)

Sound Power Level (LwA dB) 96.8 dB(A)

Vibration Levels 5.897 m/s2

Vibration Uncertainty K 1.5

Weight 0.7 kg

Speed Settings

1 6,500 (+/- 10%)

2 9,500 (+/- 10%)

3 12,500 (+/- 10%)

4 15,000 (+/- 10%)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

4. Do not operate the tool where there are flammable liquids or gases.

USE OF AIR POWERED TOOLS

1. Stay alert and use common sense - do not operate this tool when you are

tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using air tools. Eye protectors must

provide protection from flying particles from the front and the side.

3. Do not overreach - keep proper footing and balance at all times.

4. Never use oxygen, CO2, combustible gasses, or any bottled gas, as a

source of power for an air tool. This product should only be used with a

suitably rated compressed air supply.

5. Do not connect the air hose with your finger on the trigger.

6. Do not fit the sander to any stand or clamping device that may damage it.

7. Do not exceed the maximum pressure for the tool of 7 bar.

8. Keep the air hose away from heat, oil and sharp edges.

9. Check hoses for leaks or excessive wear before use, and ensure that all

connections are secure.

10. Do not use the sander for any other purpose than described in this manual.

11. Do not carry out any alterations or modifications to the tool.

12. Always disconnect from the air supply when:

• Performing any maintenance.

• The sander is not in use.

• The sander will be left unattended.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Moving to another work area.

• Passing the sander to another person.

13. Never use the sander if it is defective or operating abnormally.

14. Avoid damaging the sander by applying excessive force of any kind.

15. Always maintain the sander with care. Keep it clean for the best and safest

performance.

16. ALWAYS ensure the workpiece is firmly secured.

17. ALWAYS ensure the sander has stopped before putting it down after use.

18. ALWAYS ensure that any attachments are correctly fastened before

connecting the sander to the air supply.

19. Do not force or misuse the sander. It will do a better and safer job at the

rate for which it was designed.

20. Quick change couplings should not be located at the air tool. They add

weight and could fail due to vibration.

21. This tool vibrates with use. Vibration may be harmful to your hands or arms.

Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek

medical advice before resuming use.

SANDER-SPECIFIC SAFETY RULES

1. Inspect the sanding pad before use. Do not use if cracked or broken.

Check if possible, that the rated speed of the backing pad is at least as

high as that of the machine.

2. Avoid contact with the moving sanding pad and wear suitable gloves to

protect the hands.

3. Never start the sander unless the abrasive pad is applied to the workpiece.

4. Beware of potentially explosive atmospheres being caused by dust / fumes

resulting from sanding and use dust extraction systems where possible.

5. Always wear a face mask when using the sander as protection from

airborne particles of sanded material. Avoid disturbing existing dust and

minimise the scattering of dust in the workplace environment. Take steps to

control the dust at the point of emission.

TRANSPORTATION

1. Never carry the sander by the air supply hose.

2. Never carry the sander with your finger on the trigger.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

THE COMPRESSED AIR SUPPLY

AIR SUPPLY REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the air tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should

be regularly checked and topped up with oil. SAE 10 oil should be

used and the lubricator adjusted to approx 2 drops per minute.

• The minimum hose diameter should be 5/16”(8mm) ID and fittings

should have the same internal dimensions.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 6.2 bar

(90 psi) at the tool when running. Higher pressures and unclean air

will shorten the life of the tool due to faster wear and is a possible

safety hazard.

PRODUCT OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Sanding Pad 5 Air Exhaust Outlet/deflector

2 Drive Locking Tool 6 Speed Adjuster

3 Safety Trigger 7 Grease Nipple

4 Female air inlet

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

FITTING/REMOVING THE SANDING PAD

1. Rotate the eccentric wheel by

hand until the locking hole can be

seen through the slot in the front

housing.

2. Insert the drive locking tool into the

hole to stop the drive from

rotating.

3. Hold the drive locking tool firmly

while screwing on the sanding pad

clockwise. Make sure the sanding

pad is tight and secure.

4. The pad can be removed by unscrewing anticlockwise.

FITTING/REMOVING THE SANDING DISC

1. Fit the backing disc to the sander

by locking the moving drive

spindle with the key supplied and

screwing the disc tightly into

place.

2. Select the disc to be used which

MUST be correct disc with hook

and loop backing.

3. Press the disc firmly onto the pad

to secure it.

CONNECTING THE AIR SUPPLY

1. Connect one end of the hose to the compressed air supply.

2. Remove the protective plug from the air inlet and connect a suitable hose

as shown.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

3. Turn on the compressed air supply

and check for air leaks. Rectify any

found before proceeding.

• PTFE tape may be useful for

sealing threaded connections.

4. If required, connect an in-line mini

oiler to the sander. A mini oiler

helps to prolong the life of the tool.

5. If a mini-oiler is not being used, run

a few drops of oil through the

sander before use. It can be entered through the airline inlet or via the

hose at the nearest connection to the air supply.

6. A gauze filter is fitted inside the air inlet. Ensure this filter is always in place

and is kept clean. An airline is connected to the adapter, preferably via a

quick release coupling (not supplied).

7. Ensure the trigger is NOT depressed when connecting the air line.

• Your sander is now ready for use

• You can fit a whip hose with a quick fit coupling if required

(available from your Clarke dealer.)

OPERATION

IMPORTANT: Only use abrasive sanding pads designed for use with this type

of sanding pad.

1. To start, squeeze the trigger

against the body of the sander.

2. Rest the sander on the workpiece

before starting it. Let the sander do

the work.

• The actual weight of the sander

is normally sufficient for efficient

sanding. Do not put additional

pressure on the sander, which

would only slow down the

speed of the pad, reducing efficiency and placing an additional

burden on the motor.

3. Pass the sander back and forth in wide, overlapping areas, taking care to

keep the sander moving around at all times. Avoid dwelling in one place

for more than a moment.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

4. Release the trigger to stop the

sander.

5. Set the speed by twisting the

adjustable 4-speed regulator. The

embossed number should line up

with the mark on the air inlet to

show the speed.

• Speeds are stated in the

specification on page 2.

6. Always ensure the sander has

stopped before putting it down.

SETTING THE EXHAUST DEFLECTOR

The direction of the exhaust air

leaving the tool can be adjusted by

rotating the exhaust deflector.

1. Twist the exhaust deflector sleeve

to direct the air as required to

deflect air away from the

workpiece or operator

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the compressed air supply hose until the air supply has

been shut down or isolated at the shut off valve and the compressed air

expelled by running the tool until it stops.

2. Refer to the compressor instruction manual for the procedure to shut down

and release the compressed air.

3. Once the pressure has been released, disconnect the air supply hose from

the sander.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

Please note that factors other than the tools condition may effect its operation

and efficiency, such as reduced compressor output, excessive drain on the

airline, moisture or restrictions in the air-line, or the use of connectors of

improper size or poor condition which will reduce air supply.

DAILY OR EVERY USE

1. Before use, drain water from the air-line and compressor.

2. Lubricate the sander daily or before each use for optimum performance.

Use a high quality airline oil either via a lubricator in the air supply system or

by placing a few drops into the air inlet immediately before use. This should

be carried out regardless of whether or not an in-line lubricator is used.

3. Keep the sander clean and free from debris.

CLEANING & OVERHAULING

1. The right angle drive is fitted with a

grease nipple to provide a facility

for lubrication of the drive gears.

After extensive use, apply a shot

of general purpose grease using a

suitable grease gun.

2. Grit or gum deposits in the

mechanism may eventually

reduce efficiency. This condition

can be corrected by cleaning the

air inlet filter and flushing out the

tool with gum solvent oil or an

equal mixture of SAE No10 oil and

paraffin. Allow the mixture to soak

into the moving parts before

draining off the excess.

WARNING: MAKE SURE THAT THE SANDER IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING, OR MAINTENANCE

PROCEDURES.

Tabla de contenidos

Otros manuales de Lijadora de Clarke

Clarke

Clarke Woodworker CS6-9C Manual de instalación y operación

Clarke

Clarke EZ Sand-HDTR Manual de usuario

Clarke

Clarke Alto MP-1800 Manual de usuario

Clarke

Clarke ALTO C2K Series Manual de usuario

Clarke

Clarke FloorCrafter Guía de inicio rápido

Clarke

Clarke 01207SD Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Clarke

Clarke CMS 200 Manual de instrucciones

Clarke

Clarke CAT220 3110474 Manual

Clarke

Clarke Woodworker BS1 Manual de instalación y operación

Clarke

Clarke Contractor CBS2 Manual de instalación y operación

Clarke

Clarke EZ-8 Manual de usuario

Clarke

Clarke EZ Sand Guía de instalación y uso

Clarke

Clarke CONTRACTOR CON300 Manual

Clarke

Clarke OBS-18DC Manual de usuario

Clarke

Clarke CS4-6E Manual de instrucciones

Clarke

Clarke COS210 Manual de instrucciones

Clarke

Clarke 07097A Manual de usuario

Clarke

Clarke 07100A Manual de usuario

Clarke

Clarke CROS3 Manual de instrucciones

Clarke

Clarke CONTRACTOR CON320 Manual de instrucciones

Clarke

Clarke METALWORKER CBB200E Manual de instrucciones

Clarke

Clarke 07032C Manual de usuario

Clarke

Clarke air CAT54 Manual de instalación y operación

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Parkside

Parkside PDS 290 B2 Manual de usuario

Status

Status XPA Series Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario

Parkside

Parkside PEXS 270 Al Manual de usuario

Makita

Makita 9207SPB Manual de usuario