Clarke CAT104 Manual de instrucciones
3/4”IMPACT WRENCH
3/4”IMPACT WRENCH
MODEL No: CAT104
Part No: 3110860
OPERATION & MAINTENANCE
INSTRUCTIONS
0707
2
SPECIFICATIONS
Drive Size ...................................................3/4” Square
Max Torque ...............................................600 ft/lb (814 N.m)
Air Inlet.......................................................1/4” BSP
Ave. Air Consumption..............................7.2 cfm
Air Pressure Max .......................................6.2 bar (90psi)
Noise Level ................................................92 dB A
Vibration Level..........................................3.2 m/s2
Net Weight ................................................5 kg
Dimensions LxWxH ....................................270 x 100 x 236 mm
Part No.......................................................3110860
Please note that the details and specifications contained herein, are correct at the time of
going to print. However CLARKE International reserve the right to change specifications at
any time without prior notice. Always consult the machine’s data plate
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of 12 months
from the date of purchase. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in
any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned
to us without prior permission.
This guarantee does not effect your statutory rights.
IN THE BOX
1 X 3/4” Impact wrench with 6” Anvil
1 X Instruction Book
3
SAFETY PRECAUTIONS
IMPORTANT
FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY,
AND/OR DAMAGE TO PROPERTY.
WORK ENVIRONMENT
• Keep the work area clean and tidy.
• Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of
the way.
• Keep children and visitors away - Do not let children handle the impact wrench.
Make sure that any other persons in the work area are dressed suitably and are
wearing eye and ear protectors.
• Do not operate the impact wrench where there are flammable liquids or gases.
• Keep the air supply hose away from heat, oil and sharp edges.
• Do not fit the impact wrench to any stand or clamping device that may damage
the tool.
USE
• Stay alert and use common sense - Do not operate the impact wrench when you
are tired or under the influence of alcohol, drugs or medication.
• Always wear eye protectors when using the impact wrench - Eye protectors must
provide protection from flying particles from the front and the side.
• Always wear ear protectors when using the impact wrench.
• Do not overreach - Keep proper footing and balance at all times.
• Never use any type of bottled gas as a source of power for the impact wrench.
• Do not connect the air supply hose with your finger on the trigger of the impact
wrench.
• Do not exceed the maximum pressure for the impact wrench: 90 psi / 6.2 bar.
• Check hoses for leaks or worn condition before use, and ensure that all
connections are secure.
• Do not use the impact wrench for any other purpose than that described in this
book.
• Do not carry out any alterations or modifications to the impact wrench.
4
SAFETY PRECAUTIONS
• Always disconnect from the air supply when:
a) Performing any maintenance
b) The impact wrench is not in use.
c) The impact wrench will be left unattended.
d) Moving to another work area.
e) Passing the impact wrench to another person.
• Never use the impact wrench if it is defective or operating abnormally.
• The impact wrench should be serviced at regular intervals by qualified service
personnel.
• Avoid damaging the impact wrench for example by applying excessive force of
any kind.
• ALWAYS maintain the tool with care. Keep it clean for best and safest
performance.
• Quick change couplings should not be located at the tool. They add weight and
could fail due to vibration.
• DO NOT force or misuse the tool. It will do a better and safer job at the rate for
which it was designed.
• DO NOT remove any labels. Damaged labels should be replaced.
• This tool vibrates with use. Vibration may be harmful to your hands or arms. Stop
using the tool if discomfort, a tingling feeling or pain occurs. Seek medical advice
before resuming use.
• NEVER use standard sockets. These may shatter with serious consequences. Use
ONLY Impact sockets.
TRANSPORTATION
• Never carry the impact wrench by the air supply hose.
• Never carry the impact wrench with your finger on the trigger.
STORAGE
• When not in use the impact wrench must be disconnected from the air supply
and stored in a dry place out of the reach of children (preferably in a locked
cabinet).
• Avoid storing the impact wrench in environments where the temperature is below
0oC.
5
PARTS
Trigger
Air Regulator
Direction Selector
Anvil
AIR SUPPLY
WARNING!
COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE THOROUGHLY
FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND
COMPRESSED AIR SUPPLY.
• Use only clean, dry, regulated compressed air as a power source for the impact
wrench.
• Air compressors used with the impact wrench must comply with the appropriate
European Community safety directives.
• A build up of moisture or oil in the air compressor will accelerate wear and
corrosion in the impact wrench.
• Never exceed the maximum operating pressure for the impact wrench.
AIR HOSE
• The air hose must be rated at least 150% of the maximum operating pressure of
the tool.
Air Inlet
6
RECOMMENDED AIR SUPPLY CONNECTION
ASSEMBLY
NOTE:
ensure the compressor is turned off.
1. Connect a suitable hose to the impact wrench
using a ¼” hose adapter.
2. Connect the other end of the hose to the
compressor.
3. Your impact wrench is now ready for use.
You can fit a whip hose with a quick fit coupling if
required (available from your Clarke dealer.)
WARNING!
COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE THOROUGHLY
FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND
COMPRESSED AIR SUPPLY.
7
OPERATING INSTRUCTIONS
WARNING!
WAIT UNTIL THE ANVIL HAS STOPPED ROTATING BEFORE OPERATING THE
DIRECTION CONTROL SWITCH.
USING THE DIRECTIONAL CONTROL BUTTON
The direction control button should be used as follows.
1 For normal tightening, the impact wrench should be operated in the forward (F)
direction.
2 For loosening, the impact wrench should be operated in the reverse(R) direction.
Direction control button in
forward position Direction control button in
reverse position
Direction
control
button Direction
control
button
FITTING THE IMPACT SOCKET
1 Select the impact socket you require
WARNING!
NEVER use standard sockets. These may
shatter with serious consequences. Use
ONLY Impact sockets.
2 Push the inpact socket onto the anvil
as shown.
8
OPERATING INSTRUCTIONS
ADJUSTING THE POWER
To adjust the power, rotate
the air regulator to one of
the settings available.
0 (Low) - 9 (High).
DISCONNECTING THE AIR SUPPLY
Do not disconnect the air supply hose until the compressor has been shut down and the
compressed air released.
1. Refer to the compressor instruction book for the procedures to shut down and
release the compressed air.
2. Once the pressure has been released, disconnect the air supply hose from the
impact wrench.
3. Store the impact wrench safely in its box in a dry, secure environment
Squeeze
OPERATING THE IMPACT WRENCH
1. Locate the socket over
the nut to be tightened
or loosened.
2. Squeeze the trigger to
start the impact wrench.
3. Release the trigger to
stop the impact wrench.
Air Regulator
9
MAINTENANCE
WARNING! Make sure that the impact wrench is disconnected from the air supply before
starting any cleaning, or maintenance procedures.
Daily
• Drain water from air tank, air line and compressor.
• Pour a few drops of CLARKE Air Line Oil, into the air inlet. This should be carried out
regardless of whether or not an air line lubricator is used. If an Air line lubricator is not
used, this procedure should be repeated after every two to three hours of use.
Weekly
• Check the air inlet screen filter and clean if necessary.
• Remove the grub screw and insert a few drops of oil into the oil port on the side of
the impact wrench.
CLEANING
• Keep the body of the impact wrench clean and free from debris, Grit or gum
deposits in the tool may reduce efficiency.
SERVICE AND REPAIR
• All servicing and repair must be carried out by qualified service technicians.
NOTES
Please note that factors other than the tool may effect its operation and efficiency such
as reduced compressor output, excessive drain on the airline, moisture or restrictions in
the line, or the use of connectors of improper size or poor condition which will reduce air
supply.
**Clarke Air Line Oil is available from your CLARKE dealer part no. 3050825.
We declare that these products comply to the following standards/directives
• 98/37/EC
Model No: CAT104
Serial or Batch number: See product data plate
signature:
D. Kemp
ENGINEERING MANAGER
DECLARATION OF CONFORMITY
10
PARTS DIAGRAM
PARTS LIST
Index Part Description
No. No.
1 KL280031 Protecting
2 KL004205 Oil Seal
3 KL280001 Motor Housing
4 KL000614 Screw
5 KL280010 Anvil Bushing
6 KL280028 Anvil Collar
7 KL004175 O-Ring
8 KL280029 Spacer
9 KL280011B6 6” Anvil
10 KL280016 Hammer Pin
11 KL280012 Hammer Cage
12 KL280015 Hammer
13 KL280013 Cam
14 KL004206 Oil Seal
15 KL004108 O-Ring
16 KL280005 Front End Plate
17 KL280008 Rotor Blade
18 KL280007B Rotor
19 KL280006 Cylinder
20 KL280033 Rear Washer
21 KL002312 Ball Bearing
22 KL280009 Rear End Plate
23 KL280003 Rear Cover
24 KL001803 Spring Washer
25 KL000119 Cap Screw
Index Part Description
No. No.
26 KL000110 Cap Screw
27 KL280032 Protecting Rubber
28 KL001802 Spring Washer
29 KL280019 Valve Sleeve
30 KL280020 Reverse Valve
31 KL280030B Rear Gasket
32 KL004106 O-Ring
33 KL280023B Regulator
34 KL000802 Screw
35 KL280026B Exhaust Deflector
36 KL280024 Pin
37 KL250028 Spring
38 KL000609 Screw
39 KL280021A Trigger
40 KL003301 Spring Pin
41 KL003305 Spring Pin
42 KL280022 Valve Stem
43 KL280025 Spring
44 KL250024A Air Inlet (1/4”PF)
45 KL002313 Ball Bearing
46 KL004114 O-Ring
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Atornillador de impacto de Clarke
Clarke
Clarke CIR24B Manual de instalación y operación
Clarke
Clarke CAT91 Manual de instrucciones
Clarke
Clarke CIR13C Manual de instalación y operación
Clarke
Clarke CAT64 Manual de instrucciones
Clarke
Clarke CID20Li Manual de instrucciones
Clarke
Clarke X-Pro CAT163 Manual de instalación y operación
Clarke
Clarke CIR13C Manual de instalación y operación
Clarke
Clarke CAT64 Manual de instalación y operación
Clarke
Clarke CAT102 Manual de instrucciones
Clarke
Clarke CAT79 Manual de instalación y operación
Clarke
Clarke CAT101 Manual
Clarke
Clarke X-Pro CAT204 Manual de instalación y operación
Clarke
Clarke CEW520 Manual de instrucciones
Clarke
Clarke CAT117 Manual de instrucciones
Clarke
Clarke CAT48 Manual de instalación y operación
Clarke
Clarke CAT110 Manual de instrucciones
Clarke
Clarke CAT96 Manual de instrucciones
Clarke
Clarke CAT81 Manual de usuario
Clarke
Clarke CAT78 Manual de instalación y operación
Clarke
Clarke CIR24 Manual de instalación y operación
