Clarke SHHHAIR MAX 24/150 Manual de instrucciones

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS DL1123

LOW NOISE AIR COMPRESSOR

MODEL NO: SHHHAIR MAX 24/150

PART NO: 2242040

INTRODUCTION

Thank you for purchasing this CLARKE Air Compressor.

Before attempting to operate the machine, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to the product giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

ENVIRONMENTAL RECYCLING POLICY

By purchasing this product, the customer is taking on the obligation

to comply with current WEEE regulations.

This means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws

governing Waste Electrical and Electronic Equipment (WEEE) at a recognised

disposal facility.

This product contains valuable raw materials. Metal products should be taken

to your local civic amenity site for recycling of metal products.

GENERAL SAFETY WARNINGS

WORK AREA

1. Keep the work area clean and well lit. Floors should always be kept clear.

Cluttered or dark areas invite accidents.

2. Keep children and bystanders away while operating a power tool.

Distractions can cause loss of control.

3. The compressor should only be used in areas with adequate ventilation

and should not be exposed to heat or used near flammable substances

PERSONAL SAFETY

1. ALWAYS stay alert, watch what you are doing and use common sense

when operating the compressor. DO NOT use the compressor while you are

tired or under the influence of medication, drugs or alcohol. A moment of

inattention can result in personal injury.

2. ALWAYS use eye protection when operating compressed air equipment,

and ensure that others in the work area are protected from flying particles

from the front and from the side.

3. ALWAYS protect yourself against electric shock. NEVER operate the

compressor in wet or damp locations.

4. NEVER over-reach. Keep your proper footing and balance at all times to

enable better control of the compressor in unexpected situations.

5. NEVER attempt any complex repairs yourself. If you have a technical

problem contact your local dealer.

6. ALWAYS store the compressor out of reach of children.

7. ALWAYS protect your hearing. Ear protection should be worn when

operating this compressor and it’s associated power tools.

8. NEVER direct the air stream at people or animals, as injury may result.

Compressed air can cause soft tissue damage and propel dirt and other

particles at high speed.

9. NEVER insert your fingers or other objects inside the motor housing. NEVER

operate the compressor without the cover in place.

WARNING: WHEN USING ELECTRICAL TOOLS, BASIC SAFETY

PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK AND PERSONAL INJURY

WARNING: READ ALL THESE INSTRUCTIONS BEFORE ATTEMPTING TO

OPERATE THIS PRODUCT AND KEEP THESE INSTRUCTIONS IN A SAFE PLACE.

GENERAL MACHINE USE AND CARE

1. Prior to use, all operators should become familiar with the instructions in this

booklet especially the ON/OFF switch for emergency stopping.

2. ALWAYS maintain the compressor with care and keep it clean for best /

safest performance.

3. NEVER use this compressor if any part is damaged. Have it inspected and

repaired by your dealer.

4. NEVER attempt to modify the air compressor, tank, fittings or attachments in

any way. Doing so will invalidate the guarantee and could result in

personal injury.

5. NEVER abuse the power cable. NEVER pull on the cable when removing

the plug from the socket, or lift the compressor by the power cable.

6. Try to AV O I D using extension leads. Where possible use a longer airline hose

instead.

7. If you have to use an extension lead. ONLY use one that is of an

appropriate power rating and suitable for the work environment. Extension

leads must have an earth connection. Inspect the extension lead regularly

and replace if damaged.

8. ONLY USE RECOMMENDED PARTS: To avoid the risk of bursting, only hoses

with a rated pressure of 10 bar, or more should be used. NEVER attempt to

repair damaged hoses.

9. NEVER abuse the compressor by standing on it.

AIRLINE HOSES

1. ALWAYS ensure that equipment or power tools used in conjunction with the

compressor have a safe working pressure exceeding that of the machine.

2. ALWAYS keep the air hose away from any attached power tools and

ensure that the operator is not restricted by the length of the hose.

3. ALWAYS take care when a long air hose is required in the work area as it

presents a trip hazard. Coil the hose away as soon as the job is finished.

4. ALWAYS avoid kinking or trapping the air hose. ALWAYS replace faulty

hoses and never attempt a repair if a leak is detected.

5. NEVER abuse hoses or connectors. NEVER carry an air tool by the hose, or

yank it to disconnect from the air supply. Keep hoses away from heat, oil

and sharp edges. Check hoses for leaks or worn condition before use and

ensure that all connections are secure.

6. ALWAYS ensure that the air supply is turned off at the machine outlet and

any air pressure vented from within the compressor and any attached

equipment when disconnecting air hoses or other equipment.

AIR COMPRESSOR SAFETY INSTRUCTIONS

1. ONLY USE WITHIN THE RECOMMENDED OPERATING TEMPERATURE RANGE:

This compressor should only be used in an ambient temperature of

between 0OC and +35OC (never below freezing temperatures).

2. NEVER USE AN AIR COMPRESSOR WHICH APPEARS DEFECTIVE OR IS

OPERATING ABNORMALLY: If the compressor operates unusually or makes

strange noises, switch off immediately and purge the air reservoir. Arrange

repairs with your nearest dealer.

3. BREATHING QUALITY AIR: This compressor should not be used to supply

breathing quality air.

4. PRESSURE SAFETY VALVE: NEVER remove or attempt to adjust the safety

valve. The maximum pressure is factory set. Keep the safety valve free from

paint.

5. AVOID UNINTENTIONAL STARTING: DO NOT move the compressor when it is

connected to the mains power supply.

6. BEFORE EACH USE CHECK THE COMPRESSOR AND HOSE FOR DAMAGED

PARTS: Never use the compressor if it has been damaged in any way. Have

the compressor repaired by a qualified service engineer. DO NOT use the

compressor if the On/Off switch does not operate correctly.

7. KEEP THE MOTOR AIR VENTS CLEAR: Keep the motor vents clear and free

from dust. Wipe regularly to maintain an adequate supply of clean air.

Avoid using in dusty conditions.

8. OPERATE THE COMPRESSOR AT THE CORRECT VOLTAGE: Make sure that the

mains supply voltage is the same as the voltage shown on the label.

9. ALWAYS adjust the pressure regulator to the recommended setting for the

particular spray gun or air tool being used.

10. When using the compressor for painting:

•DO NOT work in enclosed areas or near naked flames.

• Ensure that the area in which you are working has good ventilation.

• Protect your nose and mouth with a suitable face mask.

•ALWAYS check the safety data sheets for substances being sprayed &

ensure manufacturer’s instructions are followed.

11. DO NOT USE THIS COMPRESSOR TO INFLATE SMALL, LOW-PRESSURE OBJECTS:

Items such as children's toys or footballs can explode if over-inflated.

12. NEVER STOP THE COMPRESSOR BY REMOVING THE PLUG OR SWITCHING OFF

AT THE MAINS SUPPLY: ALWAYS use the On/Off switch on the compressor.

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond

with the markings on the terminals of your plug, proceed as follows.

•TheBlue wire must be connected to the terminal marked Nor

coloured Black.

•TheBrown wire must be connected to the terminal marked Lor

coloured Red.

•TheYellow and Green wire must be connected to the terminal

marked E or or coloured Green.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD). If in any doubt, consult a qualified

electrician. DO NOT attempt any repairs yourself.

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE

MAINS SUPPLY.

WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT

ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN =

EARTH

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

OVERVIEW

DESCRIPTION DESCRIPTION

1 Drain Valve 7 Regulator

2 One Way Check Valve 8 On/Off Pressure Switch

3 Discharge Pipe 9 Air Filters

4 Tank Pressure Gauge 10 Safety Valve

5 Outlet Pressure Gauge 11 Pump

6 2 x 1/4” BSP Airline Outlet Fixing

Point With Tap

12 Air Tank

ON/OFF PRESSURE SWITCH

Switch on - Auto/Off. The compressor

will automatically switch off when the

tank pressure reaches the maximum

preset pressure (0.8Mpa, 8 Bar, 116psi)

and will run automatically when the

tank pressure reaches the minimum

preset pressure (0.6Mpa, 6 Bar, 87psi).

In the ‘OFF’ position, the compressor

will not operate. This switch should be

in the ‘OFF’ position when

connecting or disconnecting the

power cord from the electrical outlet or when changing air tools.

REGULATOR

1. The regulator adjusts the air pressure to fit an air operated tool, spray gun

of sandblaster.

2. To adjust the outlet air pressure, turn the regulator clockwise or

counterclockwise to suit the type of tool you are using.

SAFETY VALVE (PRESSURE RELEASE VALVE)

This valve will automatically release compressed air when the pressure in the

tank exceeds the allowed pressure.

DISCHARGE PIPE

This pipe connects the pump head to the check valve. CAUTION: It is hot

when the compressor is running.

CHECK VALVE

The check valve is a one way valve allowing compressed air to enter the tank,

but prevents compressed air in the tank back into the pump.

DRAIN VALVE

This valve located at the bottom of the tank is used to exhaust water from the

tank. Make sure the pressure gauge of the tank is below 1 Bar to open it. Open

the drain valve to exhaust water in the tank, closing it tightly. NOTE: This action

should be done every week.

PRESSURE GAUGES

There are 2 pressure gauges on this type of compressor, one shows the

pressure in the tank and the other one shows the outlets pressure after the

regulator has been set.

PREPARING FOR USE

CONNECTING THE WHEELS & RUBBER FOOT

1. Unscrew the nut and two washers from the wheel axle.

2. Pass the wheel axle through the

axle hole in the wheel support

frame, as shown, with a washer

either side of the hole.

3. Replace and tighten the nut onto

the axle.

NOTE: Make sure that the nut is not

too tight, so the wheel has

free movement.

1. Unscrew the nut and washers from

the rubber foot.

2. Place the rubber foot bolt through

the foot support mount on the

underside of the air tank, as

shown.

3. Replace the washer and nut onto

the bolt and tighten.

FITTING THE AIR FILTERS

1. Remove the transit plugs from the air filter inlets.

2. Screw the air filters into the inlets,

as shown

OPERATION

Before connecting your compressor to the mains supply, check the following:-

1. Firstly, ensure the compressor is on level ground. DO NOT allow it to run if it is

standing on an incline.

2. Check that the mains voltage corresponds with that shown on the data

label on the side of the compressor and the specification page (p18) of this

manual.

3. The ON/OFF switch is in the OFF

position.

STARTING THE COMPRESSOR

CAUTION: DO NOT ATTACH ANY AIR TOOLS TO THE OUTLET UNTIL THE UNIT HAS

BEEN CHECKED AND THE STARTING PROCEDURES HAVE BEEN COMPLETED.

1. Turn the regulator fully clockwise

(+) to open the airflow, making

sure the flow taps are in the

closed position.

2. Push the ON/OFF switch to the

‘OFF’ position and plug in the

power cord.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Compresor de aire de Clarke

Clarke

Clarke BOXER II 14/200 Manual de instrucciones

Clarke

Clarke Boxer 14/200 Manual de instrucciones

Clarke

Clarke PIONEER 210 OF Manual de instrucciones

Clarke

Clarke SHHH AIR 100/24 Manual de instrucciones

Clarke

Clarke CHAMP 3 Manual de instrucciones

Clarke

Clarke PANTHER 10/240 Manual de instrucciones

Clarke

Clarke AIRMASTER 18/150 Manual de instrucciones

Clarke

Clarke CHAMP 262 Manual de instalación y operación

Clarke

Clarke SHHHAIR MAX 50/350 Manual de instrucciones

Clarke

Clarke SE Ranges Manual de instalación y operación

Clarke

Clarke CSS1 Manual de instrucciones

Clarke

Clarke Hunter 54 Manual de instrucciones

Clarke

Clarke BRONCO 2 OIL FREE Guía de solución de problemas

Clarke

Clarke BOXER II 14/150 Manual de instrucciones

Clarke

Clarke AIRMASTER 14/200 Manual de instrucciones

Clarke

Clarke Air SP15ND Manual de instalación y operación

Clarke

Clarke RANGER 64 Manual de instrucciones

Clarke

Clarke Pioneer 205 Manual de instalación y operación

Clarke

Clarke RANGER 46 Manual de instrucciones

Clarke

Clarke BANDIT Manual de instrucciones

Clarke

Clarke Boxer 14/100P Manual de instrucciones

Clarke

Clarke Panther 10/500 Manual de instrucciones

Clarke

Clarke VE15C150 Manual de instrucciones

Clarke

Clarke CHAMP 265 Manual de instrucciones

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario