Clarion M202RC-RET Guía de solución de problemas
MARINE REMOTE-MOUNTED CONTROL PANEL
M202RC-RET
Owner's Manual / Installation Guide
VOLUME
VOLUME
SELECT
SELECT
BAND SOURCE
POWER
MUTE
Precautions
Make certain that the remote is installed in a location which
does not interfere with the safe and proper operation of the
boat.
TheM202RC-RET is only compatible with the M335-RET AM/
FM/CDPlayer.
About Installation
Installation of Clarion marine audio components requires
experience with a variety of mechanical and electrical
procedures. Even though this manual provides general
installation and operation instructions for your new Clarion
marine audio remote control panel, it does not show the exact
methods for your particular installation.
If you do not have the required knowledge and experience to
successfully complete the installation, we strongly recommend
consulting an authorized Clarion marine audio dealer about
professional installation options.
Table of Contents
1. Introduction..................................................................... 4
2. Care and Maintenance ...................................................4
3. Using the Remote Control Panel ...................................5
4. Installation and Wiring ...................................................7
Limited Warranty Information ......................................... 11
4 M202RC-RET
1.INTRODUCTION
The M202RC-RET is a waterproof remote control panel which
allows operation of the Clarion M335-RET head unit from a
remote location. Two M202RC-RET units may be used with a
single M335-RET (using an optional M101RYC adapter). The
M202RC-RET can be connected to your boat’s illumination
circuit, backlighting the panel in low-light conditions.
What is included
•Remote control panel (1)
•One mounting bracket and four 7mm hex nuts (1 set)
•Owner’s Manual / Installation Guide (1)
Note: An extension DIN cable is available separately
(P/N M101RXC)
2.CAREANDMAINTENANCE
Clean the remote control panel with a slightly damp, soft cloth
using household glass cleaner. Do not use solvents such as
benzene, thinner, or commercially available cleaners.
From time to time, inspect the connections on the rear of the
unit for corrosion and correct as needed.
M202RC-RET 5
3.USING THE REMOTECONTROLPANEL
Using the Remote Control Panel
This remote control allows the user to control the Clarion
M335-RET AM/FM/CD Player from a remote location, even if
the source unit is mounted out of sight in a compartment or in
a different area.
The[POWER/SOURCE] button:
SOURCE
POWER
To turn the unit on, press this button momentarily. To
turn the unit off, press and hold for 1 second.
When the M335-RET is already on, press momen
tarily to switch between the CD and the AM/FM tuner.
The [BAND] button:
BAND
In Radio mode: Switches between AM and FM
bands, and selects among the various memory
registers (FM1, FM2, etc.)
In CD mode: begins playback from the beginning of
the CD.
VOLUME
VOLUME
SELECT
SELECT
BAND SOURCE
POWER
MUTE
Display
6 M202RC-RET
The[MUTE/PLAY/PAUSE] button:
MUTE
In Radio mode: this button mutes the system. Press
the button again to defeat the mute feature.
In CD mode: this button pauses playback of the CD.
To resume playback, press this button again.
The [VOLUME UP/DOWN] buttons:
VOLUME
VOLUME
These increase and decrease the system volume. If
the [MUTE] function is active, pressing one of these
buttons defeats the mute function.
The[SELECT UP/DOWN] buttons:
SELECT
SELECT
In Radio mode: these buttons select the next
preset radio station in the memory.
In CD mode, these buttons serve two functions:
Track navigation: To select the next track on the
disc, press and release the [SELECT UP] button. To
return to the beginning of the current track, press
and release the [SELECT DOWN] button. To “back
up” a few tracks, press and release the [SELECT
DOWN] button until the desired track number is
displayed.
Searching within a track: To fast-forward or fast-
reverse within the track, press and hold the
[SELECT UP] or[SELECT DOWN] button.
M202RC-RET 7
4.INSTALLATIONAND WIRING
1. Before Starting
Read these instructions and the following precautions.
Precautions
•This unit is exclusively for boats with a negative ground,
12V power supply.
•Do not open the case. There are no user-serviceable parts
inside. If you require assistance, consult your Clarion
dealer or an authorized Clarion service center.
•Use a soft, dry cloth to gently clean the control panel after
installation. Never use a rough cloth, thinner, benzene,
alcohol, or other solvent. The screen surface can be
scratched - do not rub when cleaning.
2. Package Contents
!Remote Control Panel unit (1)
!One mounting bracket and four 7mm hex nuts (1 set)
!Owner’s Manual / Installation Guide (1)
3. Installing the Unit
Selecting the Location
Location of the panel varies.
Before you begin installation of the panel, verify that you have
sufficient clearance in the desired location. 2.5 inches is
required to avoid cable damage. A flat surface is required in
order to ensure a watertight seal when mounting is complete.
WARNING!
Before cutting any panel, ALWAYS
ensure that there is sufficient clearance
behind the panel, and that no wire
harnesses, fuel lines, moving linkages,
or any other critical components are
exposed to damage by your choice of
location. NEVER risk damage to the hull
while cutting your opening.
Prepare the boat for installation by carefully removing interior
trim panels as necessary. Route wire harnesses away from
sharp edges, and ensure that no harnesses will be pinched
or pierced during reassembly.
8 M202RC-RET
1. Determine the mounting location is a flat surface with
sufficient rear clearance (2.5”) and access. Ensure
that the installation can be successfully completed
before continuing! If the cable is not long enough, a
cable extension is available - P/N M101RXC.
2. The remote control panel requires a 2” (51mm) diameter
round hole. Cut the hole and insert the panel as shown.
VOLUME
VOLUME
SELECT
SELECT
BAND SOURCE
POWER
MUTE
3. The mounting bracket is scored with “break lines’ to allow
use with panels of different thicknesses. Determine if the
bracket needs to be shortened, and remove the appropri-
ate number of breakaway segments using a pair of pliers.
Each segment is 1/4” long.
Break Lines
4. Insert the remote control panel into the opening. Make
sure that the gasket behind the remote control panel face
seats completely against the mounting surface.
2” (51mm)
Diameter
Hole
Mounting Bracket
M202RC-RET 9
5. Position the bracket onto the rear of the remote control
panel, sliding the two threaded studs on the rear of the
panel through the two holes in the mounting bracket (as
shown below). Tighten the 7mm hex nuts onto the
bracket, again ensuring that the gasket seals tightly to
the front of the mounting surface. Avoid pinching the
cable.
Take the following precautions before wiring your system.
•Disconnect the negative battery terminal before making any wiring
connections.
•Be particularly careful where you route wires and cables. Keep
them away from the engine, exhaust system, etc. Heat may
damage wires. Sharp edges can pierce wire insulation and cable
jackets, causing short circuits, damage to the craft, blown fuses,
and system failure.
•If any fuse should blow, make sure all connections are correct
and no wires are damaged before replacing the fuse. Always use
fuses that are the same amperage value as the original. When
replacing a fuse, never let the battery side touch any metal part or
any other wire.
Wiring Connections
Wiring
1. Connecting the ground lead.
Connect a wire to one of the
mounting studs on the rear of
the unit, using a #8 ring
terminal (not supplied).
Connect this wire to the
boat’s negative (-) ground.
10 M202RC-RET
2. Connecting the illumination lead.
The illumination circuit of the M202RC-RET operates with
a 12V(+) input. Wire with a .250 female insulated spade
terminal (not supplied), and connect the illumination
terminal on the rear of the panel to a 0.5A in-line fuse (not
supplied). Connect the other side of the fuse to an
illumination circuit of the boat.
3. Connecting the cables.
Connect the DIN cable from the M335-RET AM/FM/CD
Player to the remote(s). Route it carefully to avoid moving
parts.
VOLUME
VOLUME
SELECT
SELECT
BAND SOURCE
POWER
MUTE
VOLUME
VOLUME
SELECT
SELECT
BAND SOURCE
POWER
MUTE
VOLUME
VOLUME
SELECT
SELECT
BAND SOURCE
POWER
MUTE
NOTE: A maximum of two remotes can be connected to
the M335.
M335
M335
M101RXC-24
M101RXC-24
M101RXC-24
M101RYC
M202RC
M202RC
M202RC
Connecting one remote to the XMD3
with optional M1012RXC-24 DIN cable.
Connecting two remotes to the M335 using an optional
M1012RYC and two M1012RXC-24 DIN cables.
Tabla de contenidos
Otros manuales de Panel de control de Clarion
