Cisco UCS 5100 Manual de usuario
UCS Uplink Ethernet Connection Configuration
Example
Document ID: 110267
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Configure
Network Diagram
1. Configure Uplink Ethernet Ports
2. Unconfigure an Uplink Ethernet Port
Verify
Troubleshoot
Related Information
Introduction
Each Cisco Unified Computing System (UCS) provides ports that can be configured as either Server Ports or
Uplink Ports. Ports are not reserved for specific use. They must be configured. You can add expansion
modules to increase the number of Uplink Ports on the Fabric Interconnect.
Create LAN and SAN Pin Groups in order to pin traffic from servers to a specific Uplink Port.
Prerequisites
Requirements
Cisco recommends that you have a working knowledge of UCS software and hardware before you attempt
this task.
Components Used
The information in this document is based on Cisco UCS.
The information in this document was created from devices in a specific lab environment. All of the devices
used in this document started with a default configuration. If your network is live, make sure that you
understand the potential impact of any command.
Conventions
Refer to the Cisco Technical Tips Conventions for more information on document conventions.
Configure
Cisco UCS Fabric Interconnects provide these port types:
Server PortsServer Ports handle data traffic between the Fabric Interconnect and the adapter cards
on the servers.
You can only configure Server Ports on the fixed port module. Expansion modules do not support
Server Ports.
•
Uplink Ethernet PortsUplink Ethernet Ports connect to external LAN Switches. Network bound
Ethernet traffic is pinned to one of these ports.
You can configure Uplink Ethernet Ports on either the fixed module or an expansion module.
•
Uplink Fibre Channel PortsUplink Fibre Channel Ports connect to external SAN Switches.
Network bound Fibre Channel traffic is pinned to one of these ports.
You can only configure Uplink Fibre Channel Ports on an expansion module. The fixed module does
not include Uplink Fibre Channel Ports.
•
This task describes only one method that is available to configure ports. You can also configure ports through
a right−click menu or from the General tab for the port..
Network Diagram
This is a typical topology used with the Cisco UCS:
Note that Uplink Ports are also known as border links.
1. Configure Uplink Ethernet Ports
Complete these steps:
Log into Cisco UCS Manager.1. In the Navigation pane, click the Equipment tab.2. In the Equipment tab, expand Fabric Interconnects > Fabric Interconnect_Name.3. Depending upon the location of the ports you want to configure, expand one of these:
Fixed Module♦ Expansion Module♦
4.
Choose one or more of the ports under the Unconfigured Ports node.5. Drag the selected port or ports and drop them in the Uplink Ethernet Ports node.6.
The ports to be configured as Uplink Ethernet Ports are removed from the Unconfigured Ports folder
and added to the Uplink Ethernet Ports folder.
As shown, an Uplink Ethernet Port is successfully configured. Click OK.7.
Make sure the new Uplink Ethernet Port is physically connected to your upstream LAN switch and
the proper VLANs are configured.
8.
2. Unconfigure an Uplink Ethernet Port
Complete these steps:
Log into Cisco UCS Manager.1. In the Navigation pane, click the Equipment tab.2. In the Equipment tab, expand Fabric Interconnects > Fabric Interconnect_Name.3. Depending upon the location of the ports you want to unconfigure, expand one of these:
Fixed Module♦ Expansion Module♦
4.
Choose one or more of the ports under the Uplink Ethernet Ports folder.5. Drag the selected port or ports and drop them into the Unconfigured Ports folder.6.
Click Yes in order to confirm.7.
As shown, you have successfully unconfigured an Uplink Ethernet Port.8.
Verify
There is currently no verification procedure available for this configuration.
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
Related Information
Technical Support & Documentation − Cisco Systems•
Contacts & Feedback | Help | Site Map
© 2013 − 2014 Cisco Systems, Inc. All rights reserved. Terms & Conditions | Privacy Statement | Cookie Policy | Trademarks of
Cisco Systems, Inc.
Updated: Apr 27, 2010 Document ID: 110267
Otros manuales para UCS 5100
6
Tabla de contenidos
Otros manuales de Servidor de Cisco
Cisco
Cisco C880 M4 Instrucciones de montaje
Cisco
Cisco UCS C Series Instrucciones de montaje
Cisco
Cisco UCS B200 M4 Manual de instalación y operación
Cisco
Cisco c240 Instrucciones de instalación y mantenimiento
Cisco
Cisco ONS 15454 ETSI Manual de usuario
Cisco
Cisco AS5300-96VOIP-A Manual de usuario
Cisco
Cisco C880 M4 Manual de usuario
Cisco
Cisco NCS 1001 Manual de usuario
Cisco
Cisco UCS 82598KR Manual de usuario
Cisco
Cisco UCS B420 M4 Manual
Cisco
Cisco UCS Invicta C3124SA Manual
Cisco
Cisco TelePresence Server 7010 Guía de referencia
Cisco
Cisco UCS 5108 Manual de usuario
Cisco
Cisco UCS B200 M2 Manual de usuario
Cisco
Cisco Catalyst 6800 Manual de usuario
Cisco
Cisco UCS C220 M5SX Manual de usuario
Cisco
Cisco UCS C420 Instrucciones de instalación y mantenimiento
Cisco
Cisco UCS C210 Instrucciones de instalación y mantenimiento
Cisco
Cisco Firepower 2100 Series Manual
Cisco
Cisco UCS B22 M3 Manual
