Cisco C880 M4 Instrucciones de montaje

Cisco C880 M4 Server Firmware Update Guide

First Published: August 24, 2016

Introduction

This document describes how to update the firmware on a Cisco C880 M4 server. There are two update

procedures:

•Offline Firmware Update Procedure, which should be initiated when the server is powered off.

•Online Firmware Update Procedure, which should be initiated when the server is powered on (in Boot

state).

The procedures are identical except for the state of the system when the procedure is initiated.

Both update procedures instruct you to perform a Unified Firmware Update from the Management Board

(MMB) web UI. The Unified Firmware Update updates the following firmware:

•BIOS firmware

•BMC firmware

•MMB firmware

The BIOS and BMC firmware data are stored in ROM devices on each system board (SB): 0, 1, 2, and 3. The

MMB firmware data are stored in a ROM device on the MMB.

The version of the BIOS firmware on each system board should be the same, and the version of the BMC

firmware on each system board should be the same. When a system board is replaced with a spare system

board, the version of the new system board may not be the same as the version of the firmware on other system

boards. When this situation occurs, perform a Unified Firmware Update to make all firmware versions equal.

Procedure Summary

We recommend performing the Offline Firmware Update Procedure as a part of this overall workflow:

Step 1 Shut down the OS and power off the system (but do not disconnect the power cord).

Step 2 Stop issuing IPMI commands from Cisco UCS Director to the ManageMent Board (MMB) of the C880 M4 Server.

Step 3 Perform the Unified Firmware Update from the MMB web UI to apply the firmware binary so that it starts running.

Step 4 Set the new BMC username and password as described in Changing a Username and Password .

Step 5 Resume issuing IPMI commands from Cisco UCS Director to the C880 M4 Server.

Cisco C880 M4 Server Firmware Update Guide

Offline Firmware Update Procedure

Step 1 Log in with administrator privilege to the MMB web UI.

Step 2 From the Navigation bar, choose System.

Step 3 Power off the system (but do not disconnect the AC power).

Step 4 From the Navigation bar, choose Maintenance.

Step 5 Choose Firmware Update >Unified Firmware Update.

Step 6 Choose the firmware file.

Step 7 Click Update.

Wait for the firmware version check window to appear, which takes approximately 5 minutes.

Step 8 Click OK after confirming the firmware version.

The progress bar appears in about 1 minute.

•The time required to update the firmware for a one MMB configuration is about 70 minutes.

•For a one MMB configuration, wait about 5 minutes before logging into the web UI . The web UI is disconnected

during the firmware update.

Online Firmware Update Procedure

Before You Begin

Before starting the update, ensure that the system is in boot state and the OS is not running.

Step 1 Log in with administrator privilege to the MMB web UI.

Step 2 From the Navigation bar, choose Maintenance.

Step 3 Choose Firmware Update >Unified Firmware Update.

Step 4 Choose the firmware file.

Step 5 Click Update.

Wait for the firmware version check window to appear, which takes approximately 5 minutes.

Step 6 Click OK after confirming the firmware version.

The progress bar appears in about 1 minute. The time required to update the firmware for a one MMB configuration is

about 70 minutes.

This online firmware update procedure writes a new version of the firmware to the ROM device. To apply the

new firmware to the system, power off the server and power it on again.

Note

While the new firmware is being applied to the system, the web UI is disconnected. Wait about 5 minutes before logging

into the web UI.

Cisco C880 M4 Server Firmware Update Guide

Introduction

Offline Firmware Update Procedure

Changing a Username and Password

For security purposes, the BMC login credentials configuration changed with the revision of C880 M4 Release

Version 1.0.2.

The new BMC login credentials configuration was implemented in an initial firmware revision of C880

M4 with the E7-8800 v3 CPU.

Note

•The username and password are disabled.

•The username and password can be set with a MMB CLI command.

Previously, the default username/password combination was admin/admin, which could not be changed. Once

the new firmware is applied, the BMC username and password are disabled. If you need to log into the BMC

for IPMI processing, you need to set a username and password using the MMB CLI commands listed here:

set bmc user <user id> <password> <password> quiet

user id: a username to be registered

password: a password for the username

password: the confirmation password

Example:

set bmc user admin admin admin quiet

If you enter the IPMI command to BMC without setting a new username, you receive an error message that

indicates that the username is invalid and a LAN connection cannot be established.

Cisco C880 M4 Server Firmware Update Guide

Introduction

Changing a Username and Password

Cisco C880 M4 Server Firmware Update Guide

Introduction

Changing a Username and Password

Otros manuales para C880 M4

Tabla de contenidos

Otros manuales de Servidor de Cisco

Cisco

Cisco ACE-4710-1F-K9 Manual de usuario

Cisco

Cisco VCS Series Manual de usuario

Cisco

Cisco UCS C240 M3 Manual de usuario

Cisco

Cisco UCS C220 M3 Manual de usuario

Cisco

Cisco SNS-3400 Series Instrucciones de montaje

Cisco

Cisco Profile Series Manual de usuario

Cisco

Cisco SNS-3415 series Manual de usuario

Cisco

Cisco L2TP Manual de usuario

Cisco

Cisco TelePresence Server 7010 Guía de referencia

Cisco

Cisco UCS B200 M3 Manual

Cisco

Cisco 6400 Manual de usuario

Cisco

Cisco UCS 5100 Guía rápida

Cisco

Cisco UCS C460 M4 Manual de instalación y operación

Cisco

Cisco UCS B200 M2 Manual de usuario

Cisco

Cisco Firepower 1120 Manual de usuario

Cisco

Cisco CPS-UCS-2RU-K9 Manual de usuario

Cisco

Cisco UCS B440-M1 Manual de usuario

Cisco

Cisco Expressway CE1200 Manual de usuario

Cisco

Cisco UCS C220 Instrucciones de instalación y mantenimiento

Cisco

Cisco N20-B6625-1 Manual del sistema

Cisco

Cisco UCS C220 M4 Instrucciones de montaje

Cisco

Cisco UCS B460 M4 Manual

Cisco

Cisco UCS 5100 Manual de uso y cuidado

Cisco

Cisco Firepower Management Centers Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario