Cisco VEdge 5000 Manual de usuario

Release Tab

Click!

Hardware Installation

Package Contents

Four-Post Rack Mount

Secure the router to the rack by inserting

one screw (provided in the accessory box)

into the center holeof each mounting ear.

Tighten the screw ﬁrmly.

Detach both inner rails from the two slide

rails. To do so, slide the inner bracket all

the way to the end of the slide rail.

Then push the slide rail lock outwards

in the direction indicated by the arrow.

Install the two outer rails into the

19-inch rack. To do so, clip the outer rail

ﬁrst to the front and then to the rear

post of the rack. Ensure that you align

the three holes on either side of the

outer rail to the three holes in the

front and rear posts of the rack.

Lift and insert the chassis into the outer

rails, making sure to align it on both sides,

until you hear a click.

Slide the chassis as far back as possible,

pushing the release tabs on both the inner

railsin the direction shown below.

For complete documentation, see

https://sdwan-docs.cisco.com/

Product_Documentation

Router chassis

AC power cords for your

geographical location

RJ-45 to DB-9 console cable

Rack-mounting ears

Slide rails

Mounting screws

Quick Start document

Attach the two inner rails to either side

of the router chassis using the ten inner

rail screws in the accessory box. Attach

the two mounting ears to either side of

the router chassis using the six mounting

ear screws in the accessory box.

Package Contents

Step 1 Step 2

Step 3 Step 4 Step 5 Step 6

Before installing the router or

connecting it to a power source,

read the planning and installation

instructions at:

https://sdwan-docs.cisco.com/

Product_Documentation/vEdge_Routers

Failure to observe these safety warnings

can result in personal injury or death.

Safety Standards

vEdge 5000 Router Quick Start

NOTE: If you power on the router

without inserting a NIM module,

the ZTP process will not work.

Product 78-101267-01, Rev 071118

Insert the NIM modules:

Boot the vEdge router:

Flip the On/Oﬀ switch on the rear

of the router to the ON position.

From vManage > Dashboard or

from vManage > Network > Device

Dashboard, verify that the vEdge

router is operational.

Install at least one NIM module in any

of the four available NIM slots.

Connect AC power to the vEdge router:

Plug one end of the power cord into

the AC power supply.

Plug the other end into the AC

power outlet.

Step 1 Step 2 Step 3 Step 4

Initial Conﬁguration

Caution: If you are connecting AC

power to the router, it is recommended

that the building have an external surge

protective device installed.

From vManage > Conﬁguration >

Devices > WAN Edge List > Upload

WAN Edge List, upload the WAN

Edge authorized serial number ﬁle.

From vManage > Conﬁguration >

Certiﬁcates > WAN Edge List:

a. Check that the router's chassis and

serial number are in the WAN Edge list.

b. Authorize each router by clicking

Valid in the Validate column.

c. Click Send to Controller to send the

WAN Edge list to the controller devices.

From vManage > Conﬁguration >

Templates:

a. Create a device template for the

vEdge router.

b. Attach the router to the device

template.

Conﬁgure the vEdge router:

vEdge 5000 Router Quick Start

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco uBR924 Manual de usuario

Cisco

Cisco 1710 Manual de usuario

Cisco

Cisco Linksys SFE2000 Cómo utilizar

Cisco

Cisco 807 Manual

Cisco

Cisco 8800 Series Manual

Cisco

Cisco ASR1004 - ASR 1004 Modular Expansion Base Manual de usuario

Cisco

Cisco CRS-1 - Carrier Routing System Router Manual de usuario

Cisco

Cisco Nexus 7000 Series Manual de instrucciones

Cisco

Cisco ASR 9000 Series Manual de usuario

Cisco

Cisco 4331 Manual de usuario

Cisco

Cisco WS-C2960-24LC-S Manual de usuario

Cisco

Cisco RV260 series Manual de instrucciones

Cisco

Cisco ASR 5000 Series Manual de instrucciones

Cisco

Cisco ASR 9000 Series Manual de usuario

Cisco

Cisco Small Business RV320 Manual de usuario

Cisco

Cisco ASR 14000 Series Manual de usuario

Cisco

Cisco Profile Series Manual de instrucciones

Cisco

Cisco 12406 series Guía

Cisco

Cisco 2811 - Voice Security Bundle Router Manual de usuario

Cisco

Cisco WS-C3550-12G Manual de usuario

Cisco

Cisco Universal Broadband Router uBR7200 Manual

Cisco

Cisco NCS 5000 Series Manual de usuario

Cisco

Cisco ASR 903 Manual de usuario

Cisco

Cisco VIC-2FXO - 3600 Voice Interface Card-Fxo... Instrucciones originales

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario

Cisco vEdge 5000 Manual de usuario

Manuales populares de Enrutador de red de otras marcas