Cisco NCS 5500 Series Manual de instrucciones

Connect Router to the Network

•Port Connection Guidelines , on page 1

•Connect to the Console Port, on page 2

•Create the Initial Router Configuration, on page 4

•Connect to the Management Ethernet Port, on page 6

•Installing and Removing Modular Port Adapters, on page 8

•Installing Dust Caps, on page 11

•Install and Remove Transceiver Modules, on page 12

•Connect Interface Ports, on page 21

•Connecting a Cable to the GNSS Antenna Interface , on page 22

•Maintain Transceivers and Optical Cables, on page 23

Port Connection Guidelines

Depending on the chassis and installed line cards, you can use Quad Small Form-Factor Pluggable Plus

(QSFP+), QSFP28, QSFP-DD, SFP, SFP+, CFP-DCO, and RJ-45 connectors to connect the ports on the line

cards to other network devices.

To prevent damage to the fiber-optic cables when installing a transceiver in the line card, we recommend that

you disconnect the transceiver from its fiber-optic cables. Before removing the transceiver from the router,

remove the cable from the transceiver. You can change or remove the cable without removing the transceiver.

To maximize the effectiveness and life of your transceivers and optical cables, do the following:

•Wear an ESD-preventative wrist strap that is connected to an earth ground whenever handling transceivers.

The router is typically grounded during installation and provides an ESD port to which you can connect

your wrist strap.

• Do not remove and insert a transceiver more often than is necessary. Repeated removals and insertions

can shorten its useful life.

• Keep the transceivers and fiber-optic cables clean and dust free to maintain high signal accuracy and to

prevent damage to the connectors. Attenuation (loss of light) is increased by contamination and should

be kept below 0.35 dB.

• Clean these parts before installation to prevent dust from scratching the fiber-optic cable ends.

• Clean the connectors regularly; the required frequency of cleaning depends upon the environment.

In addition, clean connectors when they are exposed to dust or accidentally touched. Both wet and

Connect Router to the Network

dry cleaning techniques can be effective; refer to your site's fiber-optic connection cleaning

procedures.

• Do not touch the ends of connectors. Touching the ends can leave fingerprints and cause other

contamination.

• Inspect routinely for dust and damage. If you suspect damage, clean and then inspect fiber ends under a

microscope to determine if damage has occurred.

Statement 1051—Laser Radiation

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or

view directly with optical instruments.

Warning

Connect to the Console Port

Before you create a network management connection for the router or connect the router to the network, you

must create a local management connection through a console terminal and configure an IP address for the

router. You also can use the console to perform the following functions (each of which can be performed

through the management interface after you make that connection):

• Configure the router using the command-line interface (CLI).

• Monitor network statistics and errors.

• Configure Simple Network Management Protocol (SNMP) agent parameters.

• Download software updates.

The system console port is an RJ-45 receptacle for connecting a data terminal to perform the initial configuration

of NCS 5500 fixed-port chassis. The console cable is shipped with the hardware.

Connect Router to the Network

Connect to the Console Port

Figure 1: NCS 55A1

Figure 2: NCS 55A2

Figure 3: NCS-55A1-48Q6H and NCS-55A1-24Q6H-S/ NCS-55A1-24Q6H-SS

Console port2Management Ethernet

port

Connect Router to the Network

Connect to the Console Port

Time of Day (ToD) port3

Follow this procedure to connect a data terminal to the console port.

Before you begin

• The router must be fully installed in its rack, connected to a power source, and grounded.

• The necessary cabling for the console, management, and network connections must be available.

• An RJ-45 rollover cable and DB9F/RJ-45 adapter are provided in the router accessory kit.

• Network cabling should already be routed to the location of the installed router.

Step 1 Set your terminal to these operational values: 115200 bps, 8 data bits, no parity, 1 stop bits (115200 8N1).

Step 2 Attach the terminal end of the cable to the interface port on the data terminal.

Step 3 Attach the other end of the cable to the console port.

Table 1: RJ-45 Straight-through Cable Pin-outs

SignalRJ-45 Pin

—1

—2

Tx3

Ground (GND)4

GND5

Rx6

—7

—8

Create the Initial Router Configuration

You must assign an IP address to the router management interface so that you can then connect the router to

the network.

When you initially power up the router, it boots up and asks a series of questions to help configure the router.

To enable you to connect the router to the network, you can use the default choices for each configuration

except for the IP address, which you must provide.

Connect Router to the Network

Create the Initial Router Configuration

These routers are designed to boot up in less than 30 minutes, provided the neighboring devices are in full

operational state.

Note

Be aware of the router's unique name to identify it among the other devices in the network.

Note

Before you begin

• A console device must be connected with the router.

• The router must be connected to a power source.

• Determine the IP address and netmask needed for the Management interfaces: MgmtEth0/RP0/CPU0/0

and MgmtEth0/RP1/CPU0/0:

Step 1 Power up the router.

The LEDs on each power supply light up (green) when the power supply units are sending power to the router, and the

software asks you to specify a password to use with the router.

Step 2 When the system is booted up for the first time, a new username and a password is to be created. The following prompt

appears:

!!!!!!!!!!!!!!!!!!!! NO root-system username is configured. Need to configure root-system username.

!!!!!!!!!!!!!!!!!!!!

--- Administrative User Dialog ---

Enter root-system username:

% Entry must not be null.

Enter root-system username: root

Enter secret:

Use the 'configure' command to modify this configuration.

User Access Verification

Username: root

Password:

RP/0/RP0/CPU0:ios#

Step 3 Enter a new password to use for this router.

The software checks the security strength of it and rejects your password if it is not considered to be a strong password.

To increase the security strength of your password, make sure that it adheres to the following guidelines:

• At least eight characters

• Minimizes or avoids the use of consecutive characters (such as "abcd")

Connect Router to the Network

Create the Initial Router Configuration

• Minimizes or avoids repeating characters (such as "aaa")

• Does not contain recognizable words from the dictionary

• Does not contain proper names

• Contains both uppercase and lowercase characters

• Contains both numbers and letters

Clear text passwords cannot include the dollar sign ($) special character.

Note

If a password is trivial (such as a short, easy-to-decipher password), the software rejects the password

configuration. Be sure to configure a strong password as described by the guidelines in this step. Passwords

are case sensitive.

Tip

If you enter a strong password, the software asks you to confirm the password.

Step 4 Reenter the password.

When you enter the same password, the software accepts the password .

Step 5 Enter the IP address for the management interface.

Step 6 Enter a network mask for the management interface.

Step 7 The software asks whether you want to edit the configuration. Enter no to not edit the configuration.

Step 8 The software asks whether you want to save the configuration. Enter yes to save the configuration.

Connect to the Management Ethernet Port

The management Ethernet port provides out-of-band management, which enables you to use the command-line

interface (CLI) to manage the router by its IP address. This port uses a 10/100/1000 Ethernet connection with

an RJ-45 interface.

To prevent an IP address conflict, do not connect the management Ethernet port until the initial configuration

is complete.

Note

To connect cables to the system management port, attach Category 5 cables directly to the RJ-45 receptacle

on the management Ethernet port.

Connect Router to the Network

Connect to the Management Ethernet Port

Figure 4: NCS 55A1

Figure 5: NCS 55A2

Figure 6: NCS-55A1-48Q6H and NCS-55A1-24Q6H-S/ NCS-55A1-24Q6H-SS

Console port2Management Ethernet

port

Connect Router to the Network

Connect to the Management Ethernet Port

To comply with GR-1089-CORE, Railway EN 50121, Smartgrid IEC 61850, and IEEE 1613, the intra-building

port(s) of the equipment must use shielded intra-building cabling/wiring that is grounded at both ends.

Note

Before you begin

You must have completed the initial router configuration.

Step 1 Plug the cable directly into the RJ-45 receptacle.

Step 2 Connect the network end of your RJ-45 cable to a switch, hub, repeater, or other external equipment.

Installing and Removing Modular Port Adapters

The following sections describe how to install or remove MPA:

Handling Modular Port Adapters

Each modular port adapter (MPA) circuit board is mounted to a metal carrier and is sensitive to electrostatic

discharge (ESD) damage.

Always handle the MPA by the carrier edges and handle; never touch the MPA components or connector pins

(See the figure below).

Caution

When a bay is not in use, a blank MPA Slot Filler must fill the empty bay to allow the router or switch to

conform to electromagnetic interference (EMI) emissions requirements and to allow proper airflow across

the installed modules. If you plan to install a MPA in a bay that is not in use, you must first remove the blank.

Figure 7: Handling a Modular Port Adapter

Connect Router to the Network

Installing and Removing Modular Port Adapters

Metal Carrier2Printed Circuit Board1

Grounding Strap3

Online Insertion and Removal

Cisco IOS XR Software 6.6.1 and later releases support online insertion and removal (OIR) of Cisco NCS

5500 series modular port adapters (MPAs). To replace an MPA in systems running earlier releases, you must

power down the chassis, replace the MPA, then power up the chassis.

Caution

Cisco NCS 5500 series modular port adapters (MPAs) support online insertion and removal (OIR).

Modular port adapters (MPAs) support the following types of OIR:

• Soft OIR

Soft OIR uses the IOS XR hw-module subslot rack/slot/subslot reload,hw-module subslot

rack/slot/subslot shutdown, and no hw-module subslot rack/slot/subslot shutdown commands to

complete online insertion and removal.

• Managed OIR

A managed online insertion and removal of Modular port adapters (MPAs) is comprised of the following

steps:

• Shut down the MPA with the hw-module subslot rack/slot/subslot shutdown command.

• Confirm that the LEDs have gone from green to off.

• Execute the do show platform command to verify that the MPA to be removed is in the disabled

state.

• Physically remove the MPA to be replaced.

• Physically insert the replacement MPA. After inserting the MPA in the slot, tighten the MPA screw

located on the right side within 10 seconds. Ensure that you first tighten the right screw and then

the left.

Tighten the captive screws on the MPA within 10 seconds. Otherwise, the MPA

shuts down and moves to Disabled state. To recover the MPA, tighten both the

captive screws and then execute the hw-module subslot rack/slot/subslot reload

command.

Note

• Return the MPA to the up state with the no hw-module subslot rack/slot/subslot shutdown

command.

• Hard OIR

You can perform the OIR in a running system, by performing the following steps, without executing any

commands:

Connect Router to the Network

Online Insertion and Removal

• Loosen the right ejector screw.

• Loosen the left ejector screw.

• Remove and replace the MPA.

Modular Port Adapter Installation and Removal

This section provides step-by-step instructions for removing and installing a modular port adapter (MPA) in

a Cisco NCS 55A2-MOD-S, Cisco NCS 55A2-MOD-SE-S or Cisco NCS 55A2-MOD-HD-S router.

After you remove the MPA from the slot, wait for 60 seconds before you reinsert the MPA.

Note

After you unscrew both ejector screws, wait for 15 seconds before removing MPA from the slot.

Note

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

Warning

To remove and install a MPA, do the following:

1. To insert the MPA, locate the guide rails inside the chassis that hold the MPA in place. They are at the

bottom left and bottom right of the MPA slot and are recessed about an inch.

2. Carefully slide the MPA all the way in the chassis until the MPA is firmly seated in the MPA interface

connector. When fully seated, the MPA might be slightly behind the faceplate.

The MPA will slide easily into the slot if it is properly aligned on the tracks. If the MPA does not slide easily,

do NOT force it. Remove the MPA and reposition it, paying close attention to engaging it on the tracks. Push

the MPA inside the slot until you hear a click. Continue to push the MPA further until you hear a second click.

The MPA is fully seated only after the second click is heard.

Note

3. After the MPA is properly seated, use a number 2 Phillips screwdriver to tighten the captive screws on

the MPA. Ensure that you first tighten the right screw and then the left.

Tighten the captive screws on the MPA within 10 seconds. Otherwise, the MPA shuts down and moves to

Disabled state. To recover the MPA, tighten both the captive screws and then execute the hw-module subslot

rack/slot/subslot reload command.

Note

Connect Router to the Network

Modular Port Adapter Installation and Removal

Otros manuales para NCS 5500 Series

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco 3845 - Security Bundle Router Manual de usuario

Cisco

Cisco 809 Manual

Cisco

Cisco CGR 1120 Manual de usuario

Cisco

Cisco NCS 540 Series Manual de instalación

Cisco

Cisco HGA5T-3 Manual de usuario

Cisco

Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1... Manual de usuario

Cisco

Cisco 3700 - 32 To 128MB Manual

Cisco

Cisco XR 12410 Manual de usuario

Cisco

Cisco ASR-920-24SZ-IM Manual de usuario

Cisco

Cisco NCS 5000 Series Manual de usuario

Cisco

Cisco Aironet 1000 Series Manual de usuario

Cisco

Cisco DC Power Entry 10005 ESR Manual de usuario

Cisco

Cisco CISCO7206 Manual de usuario

Cisco

Cisco 828 Manual de usuario

Cisco

Cisco ASR 1002-HX Manual de usuario

Cisco

Cisco 827-4V - 827-4V Router - EN Guía rápida

Cisco

Cisco ASR 1002 Manual de usuario

Cisco

Cisco 2811 - Voice Security Bundle Router Manual de instrucciones

Cisco

Cisco ASR1006-10G-SEC/K9 - ASR 1006 VPN+FW Bundle... Manual de usuario

Cisco

Cisco 1712 - Security Access Router Manual

Cisco

Cisco C11 1 8P Series Manual

Cisco

Cisco NCS 4216 Manual de instrucciones

Cisco

Cisco 7401ASR Manual del operador

Cisco

Cisco 3825 Series Guía de inicio rápido

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario