Cisco ASR 903 Manual de usuario

Cisco ASR 903 and ASR 903U Aggregation Services Router Quick Start

Guide

Revised: January 19, 2018,

Cisco ASR 903 and ASR 903U Aggregation Services Router

Quick Start Guide

The Cisco ASR 903 Router and the Cisco ASR 903U Router are collectively referred to as the Cisco ASR

903 Router in this document. Any differences between the routers are specifically called out.

Note

The Cisco ASR 903 Router is a fully-featured aggregation platform designed for the cost-effective delivery of converged mobile

and business services. With shallow depth, low power consumption, and an extended temperature range, this compact 3-rack-unit

(RU) router provides high service scale, full redundancy, and flexible hardware configuration.

Overview

The Cisco ASR 903 and the Cisco ASR903U routers expands the Cisco service provider product portfolio by providing a rich and

scalable feature set of Layer 2 VPN (L2VPN) and Layer 3 VPN (L3VPN) services in a compact package. It also supports a variety

of software features, including Carrier Ethernet features, Timing over Packet, and pseudowire.

The Cisco ASR 903 Router is positioned as a pre-aggregation router in IP RAN (GSM, UMTS, iMAX, CDMA, and LTE) networks

or an aggregation router in Carrier Ethernet networks.

The figure below illustrates the router chassis design.

Figure 1: Router Chassis Design

Interface modules1

RSP unit (with active and standby RSP slots)2

Fan tray3

Redundant power units (two DC power units are shown)4

Power Supply Features

The Cisco ASR 903 Router support AC and DC power supplies. For more information about installing the Cisco ASR 903 Router

power supplies, see the Installing the Power Supply.

To estimate the required power supply, use the Cisco Power Calculator.

The power sections provide more information about the power supply:

Redundancy

The Cisco ASR 903 Router chassis includes a slot for an optional redundant power supply. The redundant power supply option

provides a second power supply to ensure that power to the chassis continues uninterrupted if one power supply fails or input power

on one line fails. Redundancy is supported either with identical power supplies or a combination of AC and DC power supply. The

Cisco ASR 903 Router supports current sharing between the power supplies.

A redundant power supply on the Cisco ASR 903 Router is recommended. Each power supply should be connected to separate

independent power sources to ensure that the router maintains power in the event of a power interruption caused by an electrical

failure, a wiring fault, or a tripped circuit breaker.

To comply with IEC 61850-3 (voltage interruptions), redundant power supplies with separately derived

power feeds are required.

Caution

Dying Gasp

The Cisco ASR 903 Router DC power supply supports the Dying Gasp feature, which allows the router to provide an input power

loss notification to the RSP so that the RSP can send appropriate SNMP traps or OAM messages and update log files on the router.

With the DC power supply, the router supports a minimum input power loss detection time of 2 milliseconds (DC) and continued

operation of at least 6 milliseconds (DC) after the notification.

Continued DC power supply operation may vary for voltages other than +24/-48V.Note

Dying Gasp is not supported on the ASR 900 RSP3 module for 1200W DC power supply.Note

Status LEDs

LEDs are also provided on each power supply to indicate the status of the input power and the health of the power supply. For more

information about the LEDs on the Cisco ASR 903 Router, see the Troubleshoting section in the Cisco ASR 903 and ASR 903U

Aggregation Services Router Hardware Installation Guide.

Fan Tray

The fan tray has the following hardware features:

•It provides side-to-side forced air cooling

•It provides redundant fans

•It is field replaceable

•It contains status LEDs

•It contains an alarm port with four external alarm inputs

Dust Filter (A903-FAN-F)

The dust filter (see Figure 1-7 ) on the fan tray is a quadrafoam 45PPI filter which is 85 percent dust resistant. A dummy cover

(A903-FAN-F-B) secures the dust filter in the chassis. For installing the fan filter, see Installing the Dust Filter .

Use the pull tab provided to easily access the filter.Note

Air Plenum

Air Plenum or air baffle assembly (see Figure 3-7 ) is used change the air flow pattern of the unit. When the router is installed with

the plenum, the air flow pattern is changed from side-side to front-back. The air flow front-back pattern provides a rack installation

bay with a cool front zone and hot rear zone.

When the air plenum and the fan filter are installed in the chassis, the system operating temperature is

limited to 55 degrees Celsius.

Note

The air plenum is available from GAW (www.GawTechnology.net). To order an air plenum, contact the Sales and Marketing support

staff at GAW.

RSP Modules

The Cisco ASR 903 Router is designed to use up to two RSP modules to handle the data plane, network timing, and control plane

functionalities for the router. The RSP configuration allows you to use Cisco IOS software to control chassis management, redundancy,

external management, and system status indications on the router.

RSP features include:

•Loading software onto processor-based interface modules

•Redundant RSP management—The RSP manages detection of RSPs, exchange of health and status information, role negotiation,

function for detection, health and status exchange, role negotiation

•Packet processing

•Traffic management, including buffering, queuing, and scheduling, Ethernet MAC functions

•Network clocking functions including phase and time-of-day for BITS, 1 PPS, 10 MHz, and 1588 PTP clock references.

•Storage of software images, system configuration, OBFL, SysLog

•PTP packet processing including IEEE 1588-2008 for recovering network timing (frequency, phase, and time) from upstream

PTP clocks, for generating PTP frequency and phase references as inputs to the SETS, and for distributing them to downstream

PTP clocks

•External management interfaces (RS232 console, management ENET, USB console, USB storage) and system status LED

indicators

Supported RSP Features

The RSP provides the following features on the Cisco router:

•Centralized data plane, timing, and control plane functions for the system

•High-level control of interface modules

•Management functionalities for the router

•Control plane (host) CPU and associated memory in which IOS-XE and platform control software runs

•Nonvolatile memory for storage of software images, configurations, and system files

•Enabling and monitoring the health and presence of fan trays, interface modules, and power supplies

•Field replacement and hot-swap capabilities

RSP Redundancy

The Cisco ASR 903 Router chassis includes two RSP slots to allow for redundant RSPs. When the router uses redundant RSPs, one

RSP operates in the active mode and the other operates in the hot standby mode. Removal or failure of the active RSP results in an

automatic switchover to the standby RSP.

If you are using redundant RSPs, both the RSPs must be of the same type because a mixed configuration

of two different RSP types is not supported.

Note

GNSS Module (A900-CM-GNSS)

The GNSS module is present on the RSP3 modules. It is a pluggable module that allows direct interface with the external antenna.

Using a single GPS antenna input for both RSPs requires usage of external splitters.Note

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023Warning

The GNSS module is not hot swappable.Note

GNSS Module RF Input Requirements

•The GNSS module requires an active GPS/GNSS antenna with built-in Low-Noise Amplifier (LNA) for optimal performance.

The antenna LNA amplifies the received satellite signals for two purposes:

◦Compensation of losses on the cable

◦Lifting the signal amplitude in the suitable range for the receiver frontend

The Amplification required is 22dB gain + cable/connector loss + Splitter signal loss.

The recommended range of LNA gain (LNA gain minus all cable and connector losses) at the connector of the receiver module

is 22dB to 30dB with a minimum of 20dB and a maximum of 35dB.

•GNSS module provides 5V to the active antenna through the same RF input.

•Surge requirement:

◦GNSS modules have built-in ESD protections on all pins, including the RF-input pin. However, additional surge protection

may be required if rooftop antennas are being connected, to meet the regulations and standards for lightning protection in

the countries where the end-product is installed.

◦A lightning protection must be mounted at the place where the antenna cable enters the building. The primary lightning

protection must be capable of conducting all potentially dangerous electrical energy to PE (Protective Earth).

◦Surge arrestors should support DC-pass and suitable for the GPS frequency range (1.575GHz) with low attenuation.

•Antenna Sky visibility:

◦GPS signals can only be received on a direct line of sight between antenna and satellite. The antenna should see as much

as possible from the total sky. For proper timing, minimum of four satellites should be locked.

The antenna terminal should be earthed at the building entrance in accordance with the

ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93,

Grounding of Outer Conductive Shield of a Coaxial Cable.

Note

•Use a passive splitter if more than one GNSS modules are fed from a single antenna.

The splitter should have all the RF ports capable of DC-pass, if the antenna needs to feed power from

GNSS module.

Note

Interface Modules

The Cisco ASR 903 Router interface modules are a field-replaceable units. In addition to the ports provided on an RSP, the Cisco

ASR 903 Router supports the following interface modules:

For information about supported interface modules, see the Release Notes for the Cisco ASR 903 Series

Aggregation Services Router.

Note

Installing the Router in a Rack

The following sections describe how to install the Cisco ASR 903 Router in a rack:

Installing the Chassis Brackets

The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To install the brackets on the

front of the chassis, perform these steps:

Procedure

Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the router chassis. The figure below

hows how to attach the brackets on the Cisco ASR 903 Router for a 19-inch EIA rack.

Figure 2: Attaching Mounting Brackets for a 19-inch EIA Rack

The figure below shows how to attach the brackets on the Cisco ASR 903 Router for a 300 mm ETSI cabinet.

Figure 3: Attaching Mounting Brackets for a 300 mm ETSI Cabinet

Step 2 Position one of the brackets against the chassis side, and align the screw holes.

Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1 . The recommended maximum torque

is 28 in.-lb (3.16 N-m).

The A903-FAN-E fan tray with filter (A903-FAN-F) cannot be mounted using the mounting screws that are supported for

A903-FAN fan tray. This is not an issue with the FAN tray filter blank panel (A903-FAN-F-B). We recommend that you

use the short screws provided in the following rack mount kits to avoid interference of the air filter during rack mounting

and while replacing the fan tray (A903-FAN) with the fan tray (A903-FAN-E):

•19”rack mount kit (A903-RCKMT-19IN)

•ETSI rack mount kit (A903-RCKMT-ETSI)

What to Do Next

Repeat Step 2 and Step 3 for the other bracket.

Installing the Router Chassis in the Rack

To install the router chassis in the equipment rack, perform these steps:

Procedure

Step 1 Position the chassis in the rack as follows:

•If the front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between the mounting

posts.

•If the rear of the chassis is at the front of the rack, insert the front of the chassis between the mounting posts.

Step 2 Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the equipment rack.

Do not use interface module and power supply ejector handles to lift the chassis; using the handles to lift the

chassis can deform or damage the handles.

Caution

Figure 4: Installing the Chassis in a 19-inch EIA Rack

Step 3 Install the 8 or 12 (4 or 6 per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch screws through the holes in the bracket and into

the threaded holes in the equipment rack posts.

Step 4 Use a tape measure and level to verify that the chassis is installed straight and level.

Installing the Chassis Ground Connection

Before you connect the power or turn on the power to the Cisco ASR 903 Router, you must provide an adequate chassis ground

(earth) connection to your router.

This section describes how to ground the Cisco ASR 903 Router chassis. The router provides two locations for attaching a 2-hole

grounding lug according to the rack-mounting brackets you use to install the router.

Figure 5: Attaching a Grounding Lug to the Rear of the Router in an EIA 19-inch Rack

Grounding lug (19-inch EIA rack)1

Before making connections to the router, ensure that you disconnect the power at the circuit breaker.

Otherwise, severe injury to you or damage to the router may occur.

Caution

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority

or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning

Use copper conductors only. Statement 1025Warning

When installing the unit, the ground connection must always be made first and disconnected last. Statement

Warning

This unit is to be installed in a restrictive access location and must be permanently grounded to minimum 6 AWG copper ground

wire.

Procedure

Step 1 If your ground wire is insulated, use a wire-stripping tool to strip the ground wire to 0.5 inch ± 0.02 inch (12.7 mm ±0.5

mm) ( as shown in the figure below).

Figure 6: Stripping a Ground Wire

Otros manuales para ASR 903

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco 3700 series Manual de usuario

Cisco

Cisco SB 100 Series Instrucciones originales

Cisco

Cisco CISCO1751 Manual de usuario

Cisco

Cisco 2610 - Router - EN Manual de usuario

Cisco

Cisco EA-Series Manual de usuario

Cisco

Cisco CRS-1 - Carrier Routing System Router Manual de usuario

Cisco

Cisco 805 Series Manual de usuario

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Manual de usuario

Cisco

Cisco GRS Manual de usuario

Cisco

Cisco Linksys E1200 Manual de usuario

Cisco

Cisco WRT350N Manual de usuario

Cisco

Cisco SN 5428-2 Cómo utilizar

Cisco

Cisco 3800 Series Manual de usuario

Cisco

Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1... Manual de usuario

Cisco

Cisco 500 Series Instrucciones originales

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Instrucciones de funcionamiento

Cisco

Cisco ASR 903 Cómo utilizar

Cisco

Cisco Small Business RV215W Manual de instrucciones

Cisco

Cisco 7513 Series Manual de usuario

Cisco

Cisco ASR 900 Series Manual de usuario

Cisco

Cisco ASR 9000 Series Instrucciones de uso

Cisco

Cisco SGE2000 Manual de instrucciones

Cisco

Cisco 3200 Series Manual de instalación y operación

Cisco

Cisco NCS 4000 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario