Cisco 8201 Manual de usuario

Replace Chassis Components

•Replace Fan Modules for Cisco 8201 Routers, on page 1

•Replace Power Supply, on page 3

Replace Fan Modules for Cisco 8201 Routers

The fan module is designed to be removed and replaced while the system is operating without presenting an

electrical hazard or damage to the system. Please keep the replacement fan modules ready prior to attempting

this task.

The routers support FAN-1RU-PI (port-side intake airflow) and FAN-1RU-PE (port-side exhaust airflow)

fan modules.

Note

The airflow direction must be the same for all power supply and fan modules in the chassis.

Note

Step 1 To remove a fan module, follow these steps:

a) Press two latches on the fan module and grasp the handle of fan module.

Replace Chassis Components

Figure 1: Cisco 8201 Router —Remove Fans

Latched fan module1

b) As you simultaneously press the latches pull the fan module fully out of the chassis.

Step 2 To install a fan module, follow these steps:

a) Hold the fan module with the LED at the top.

b) Align the fan module to the open fan tray slot in the chassis, and press the module all the way into the slot until the

left and right latches click and are locked on the chassis.

Replace Chassis Components

Replace Fan Modules for Cisco 8201 Routers

If the fan module does not go all the way into the slot, do not force it. Remove the fan module and verify

that it is the correct type for your router and in the correct orientation. To verify the status of fans and the

speed, use the show environment fan command.

Note

c) If the chassis is powered on, listen for the sound of the fans in operation. You should immediately hear them in

operation. If you do not hear them, ensure that the fan module is inserted completely in the chassis.

During the fan module replacement, the other fans adjust their speed to allow for proper initialization of

the new module. When you insert a new fan module, the fans may run at lower or higher speeds for a few

minutes.

Note

d) Verify that the fan module LED is green. If the LED is not green, one or more fans are faulty. If this situation occurs,

contact your customer service representative for replacement parts.

Replace Power Supply

Use this procedure to replace the AC or DC power supply units. Be sure to power down the fixed configuration

PDU (power distribution unit) before removing it from the chassis.

Step 1 If the power supply is connected to a AC or DC circuit, shut off the circuit at the circuit breaker.

Step 2 Disconnect the PSU cable.

Step 3 Press the tab inward to unlatch the PSU, and pull the handle to remove the PSU.

Step 4 Insert the new PSU.

If the PSU does not go all the way into the slot, do not force it. Remove the PSU and verify that it is the correct

type for your router and in the correct orientation.

Note

Step 5 Connect the PSU cable.

Step 6 If the power supply is connected to a DC circuit, turn on the circuit breaker for the DC power source. After replacing the

PSU, verify the power using the show environment power command.

Replace Chassis Components

Replace Power Supply

Figure 2: Cisco 8201 Router —Remove Power Supply

Power supply1

Replace Chassis Components

Replace Power Supply

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco Linksys E4200 Manual del propietario

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Manual

Cisco

Cisco 890 Series Manual de usuario

Cisco

Cisco WRT54G2 Linksys Manual de usuario

Cisco

Cisco 1751V Manual

Cisco

Cisco ASR1004 - ASR 1004 Modular Expansion Base Manual

Cisco

Cisco SRP521W Manual de usuario

Cisco

Cisco 1721 - VPN Security Router Bundle Manual

Cisco

Cisco ASR 900 Series Manual de usuario

Cisco

Cisco ASR 920 series Manual de usuario

Cisco

Cisco 1600 series Manual de usuario

Cisco

Cisco SG 300-10P Manual de usuario

Cisco

Cisco 3200 Series Manual de instalación y operación

Cisco

Cisco RV132W Manual de usuario

Cisco

Cisco 7609-S Manual de usuario

Cisco

Cisco Rugged Series Manual de usuario

Cisco

Cisco 1005 Guía de instalación

Cisco

Cisco uBR10012 Universal Broadband Router... Manual de usuario

Cisco

Cisco ASR 903 Manual

Cisco

Cisco 4331 Manual de usuario

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Manual

Cisco

Cisco ASA 5508-X Manual de usuario

Cisco

Cisco ASR 14000 Series Manual de instalación

Cisco

Cisco RV260P Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario