Cisco ONS 15454 M6 Manual de usuario

Installing the ONS 15454 M6 Shelf

This chapter explains how to install the ONS 15454 M6 shelf.

Unless otherwise specified, the ECU module refers to the ECU, ECU2, ECU-S, and ECU-60V units. For

details about the various ECU modules, see the External Connection Units, on page 72.

Note

•ANSI Rack Installation, on page 2

•ETSI Rack Installation, on page 4

•Air Deflector, on page 6

•Air Plenum, on page 6

•Air Plenum Rack and Cabinet Compatibility, on page 8

•NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf, on page 9

•Air Flow Performance of ONS 15454 M6, on page 23

•NTP-G252 Install the ONS 15454 M6 Shelf , on page 24

•Front Door, on page 50

•NTP-G258 Install the Standard Door of the ONS 15454 M6 Shelf , on page 53

•NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6 Shelf , on page 57

•NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf, on page 62

•NTP-G329 Remove the Deep-Front Panel of the ONS 15454 M6 Shelf , on page 69

•External Connection Units, on page 72

•NTP-G253 Install the ECU or ECU-S Module, on page 79

•NTP-L68 Upgrading to ONS 15454 M6 ECU60-S Module, on page 82

•Power Modules, on page 82

•NTP-G524 Install the Power Modules in the ONS 15454 M6 Shelf , on page 85

•LCD Unit, on page 96

•NTP-G255 Install the LCD Module in the ONS 15454 M6 Shelf, on page 96

•Power and Ground Description, on page 98

•NTP-G256 Install Power and Ground to the ONS 15454 M6 Shelf , on page 100

•Fan-Tray Assembly , on page 117

•NTP-G257 Install the Fan-Tray Assembly in the ONS 15454 M6 Shelf, on page 118

•Cable Routing and Management, on page 120

•NTP-G290 Install the Cable and Fiber Modules, on page 121

Installing the ONS 15454 M6 Shelf

•NTP-G312 Attach Wires to Alarm, Timing, LAN, and Craft Pin Connections in Cisco ONS 15454 M6,

on page 127

•NTP-G308 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves,

on page 137

•NTP-G309 Connect the ONS 15454 M6 and the ONS 15454 in a Mixed Multishelf Configuration, on

page 139

•NTP-G310 Upgrade the ONS 15454 Multishelf Configuration Using the ONS 15454 M6 , on page 149

•NTP-G264 Perform the ONS 15454 M6 Shelf Installation Acceptance Test , on page 155

•NTP-G317 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves

with Simplex Controllers, on page 158

•NTP-G318 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves

in a Ring Topology, on page 160

•Air Deflector, on page 161

•Filler and Blank Cards, on page 162

•Air Filter , on page 162

•Shelf Voltage and Temperature, on page 163

•Cooling Profile, on page 163

ANSI Rack Installation

The ONS 15454 M6 shelf is mounted on a 19-inch (482.6-mm) or 23-inch (584.2-mm) equipment rack. Make

sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M6 shelf as shown in

Figure 1. If the shelf is mounted in the front position, then it projects 1.7 inches (43.18 mm) from the front

of the rack. If the shelf is mounted in the middle position, then it projects 5.1 inches (129.54 mm) from the

front of the rack. The shelf mounts in both Electronic Industries Alliance (EIA) standard and Telcordia-standard

racks. The shelf is a total of 17 inches (431.8 mm) wide with no mounting ears attached. Ring runs are not

provided by Cisco and might hinder side-by-side installation of shelves where space is limited.

The ONS 15454 M6 shelf measures 10.4 inches (264.16 mm) high, 19 or 23 inches (482.6 or 584.2 mm) wide

(depending on which way the mounting ears are attached), and 11.1 inches (304.8 mm) deep. You can install

up to seven ONS 15454 M6 shelves in a 7-foot (2133.6 mm) equipment rack.

The following figure shows the dimensions of the ONS 15454 M6 shelf on a 19-inch (482.6 mm) ANSI rack

configuration with brackets mounted in the front position.

Installing the ONS 15454 M6 Shelf

ANSI Rack Installation

Figure 1: Cisco ONS 15454 M6 Shelf Dimensions for a 19-inch ANSI Rack Configuration

Reversible Mounting Bracket

Use only the fastening hardware provided with the ONS 15454 M6 shelf to prevent loosening, deterioration,

and electromechanical corrosion of the hardware and joined material.

Caution

When mounting the ONS 15454 M6 shelf in a frame with a nonconductive coating (such as paint, lacquer,

or enamel) either use the thread-forming screws provided with the ONS 15454 M6 shipping kit, or remove

the coating from the threads to ensure electrical continuity.

Caution

The reversible mounting bracket is used to mount the shelf on a 19-inch or 23-inch (482.6 mm or 584.2 mm)

rack.

Mounting a Single Shelf

Mounting the ONS 15454 M6 shelf on a rack requires a minimum of 10.4-inches (265 mm) of vertical rack

space. To ensure that the mounting is secure, use two to three #12-24 mounting screws for each side of the

shelf. For an ANSI rack, the brackets can be mounted in the front or middle position.

Installing the ONS 15454 M6 Shelf

Reversible Mounting Bracket

If the ONS 15454 M6 shelf is fully loaded, then two people should install it. However, it is possible for one

person to install an empty shelf. The shelf should be empty for easier lifting.

Mounting Multiple Nodes

Most standard (Telcordia GR-63-CORE, 19-inch (482.6-mm) or 23-inch (584.2-mm) 7-foot (2.133-m) racks

can hold seven ONS 15454 M6 shelves and a fuse and alarm panel. However, unequal flange racks are limited

to six ONS 15454 M6 shelves and a fuse and alarm panel, or seven ONS 15454 M6 shelves using a fuse and

alarm panel from an adjacent rack. In an ANSI shelf, the brackets can be mounted in the front or middle

position.

The ONS 15454 M6 shelves can be mounted above each other without any space between the shelves. This

method of mounting does not restrict the air flow because the air vents are on either sides of the ONS 15454

M6 shelves.

ETSI Rack Installation

The ONS 15454 M6 shelf is mounted on a 600 x 600-mm (23.6 x 23.6-inch) or 600 x 300-mm (23.6 x

11.8-inch) ETSI standard equipment rack. In an ETSI rack, the shelf can be mounted only in the front position.

The shelf projects 1.7 inch (43.18 mm) from the front of the rack and is a total of 431.8 mm (17 inch) wide

with no mounting ears attached. Cisco does not provide ring runs, which might hinder side-by-side installation

of shelves where space is limited.

The ONS 15454 M6 shelf measures 264.16 mm (10.4 inches) high, 535 mm (21.06 inches) wide, and 304.8

mm (11.1 inches) deep. You can install up to seven ONS 15454 M6 shelves in a 7-foot (2133.6-mm) equipment

rack.

The following figure provides the dimensions of the ONS 15454 M6 shelf installed on a 600 x 600-mm (23.6

x 23.6-inch) ETSI standard equipment rack.

Installing the ONS 15454 M6 Shelf

Mounting Multiple Nodes

Figure 2: Cisco ONS 15454 M6 Shelf Dimensions for an ETSI Rack Configuration

The standard ETSI racks can hold seven ONS 15454 M6 shelves. When mounting a shelf in a partially filled

rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the

rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the

rack.

Caution

Mounting a Single Node

The ONS 15454 M6 requires 264.16 mm (10.4-inches) minimum of vertical rack space. To ensure the mounting

is secure, use two to three M6 mounting screws for each side of the shelf. A shelf should be mounted at the

bottom of the rack if it is the only unit in the rack.

In an ETSI rack, the brackets are mounted only in the front position.

If the ONS 15454 M6 shelf is fully loaded, then two people should install it. However, it is possible for one

person to install an empty shelf. The shelf should be empty for easier lifting. For information on the ONS

15454 M6 shelf weight, see the Dimensions.

Installing the ONS 15454 M6 Shelf

Mounting a Single Node

Mounting Multiple Nodes

Most standard (ETS 300 119) ETSI 600 x 600 x 2200 mm or 600 x 300 x 2200 mm racks can hold seven

ONS 15454 M6 shelves, and a fuse and alarm panel. In an ETSI rack, the brackets are mounted only in the

front position.

The ONS 15454 M6 shelves can be mounted above each other without any space between the shelves. This

method of mounting does not restrict the air flow because the air vents are on either sides of the ONS 15454

M6 shelves.

Air Deflector

An air deflector is a sheet-metal part that is mounted on the ONS 15454 M6 shelf to orient the air flow in a

specific direction.

The air deflectors can be mounted in different positions to control the air flow:

• Front to Front— Only ETSI rack

• Front to Back— For ANSI and ETSI racks

• Front to Top— Only ETSI rack

In an ANSI rack, the air deflectors are mounted only on the 23-inch rack configuration.

Air Plenum

Air plenum orients the air flow in the front-to-back direction inside the equipment to be compliant with GR-63

issue 4 requirement.

The air plenum kit has two horizontal and two vertical air plenums. The air that flows from the front top inlet

and the front bottom inlet are channelized to the right vertical plenum, inside the equipment, and then to the

exhaust air channel towards the left vertical air plenum. The air flow is deflected by 90 degrees and exited

out in the rear end.

The following figure shows the air flow inside the cabinet.

Installing the ONS 15454 M6 Shelf

Mounting Multiple Nodes

Figure 3: Air flow within the air plenum in the cabinet

The following two figures shows the dimensions of the air plenum relative to the cabinet or rack.

Figure 4: Dimension of Cisco ONS 15454 M6 chassis relative to the air plenum

Installing the ONS 15454 M6 Shelf

Air Plenum

Figure 5: Dimension on Cisco ONS 15454 M6 relative to the air plenum

Air Plenum Rack and Cabinet Compatibility

The table shows the compatibility of air plenum with the ANSI and ETSI racks and cabinets. The chassis can

be installed with brackets in front position only.

Table 1: Air plenum compatibility with racks and cabinets

Front-to-back air flowRack / Cabinet

SupportedANSI 19-inch rack

SupportedANSI 19-inch cabinet

SupportedANSI 23-inch rack

SupportedANSI 23-inch cabinet

SupportedETSI cabinet

A minimum opening of 20.600 inches is required to install the vertical air plenum behind the front rails.

The ANSI 19-inch two post rack that is compatible with air plenum installation is available from Telect, with

part number 12545-301.

Note

Installing the ONS 15454 M6 Shelf

Air Plenum Rack and Cabinet Compatibility

Figure 6: Minimum rear opening for ANSI 19-inch and ETSI configuration

NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf

This procedure installs the air plenum to orient the air flow from front-to- back

direction in the ONS 15454 M6 shelf.

Purpose

• #2 Phillips Dynamometric screwdriver

• Medium slot-head screwdriver

• Small slot-head screwdriver

• Screws

• ANSI: #12-24 x 0.50 pan-head Phillips screws

• ETSI: M6.0 x 20 pan-head Phillips screws

• Wing head screws (8)

• Adapter plates

• One air plenum kit (horizontal and vertical air plenums)

Tools/Equipment

As neededRequired/As Needed

OnsiteOnsite/Remote

NoneSecurity Level

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Statement 1074

Warning

Before working on a chassis or working near power supplies, unplug the power cord on AC units.

Statement 246

Warning

Installing the ONS 15454 M6 Shelf

NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during

normal use. Statement 39

Warning

For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC.

Note

Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and

electromechanical corrosion of the hardware and joined material.

Note

When installing or replacing the unit, the ground connection must always be made first and disconnected

last. Statement 1046

Warning

The air plenum is installed on a rack or a cabinet using thread-forming screws that remove any paint

or non-conductive coatings inside the hole threads, and establish a metal-to-metal contact. Also, clean

both surfaces outside the screw points that come in contact, so that they are free of paint and other

nonconductive coating. Apply an appropriate antioxidant compound to the surfaces.

Warning

Procedure

Depending on the rack or cabinet, complete the necessary task:

•DLP-G766 Install Air Plenum for ONS 15454 M6 Shelf in ANSI 19-inch Cabinet, on page 10

•DLP-G767 Install Air Plenum in ONS 15454 M6 Shelf for ANSI 23-inch Configuration, on page 14

•DLP-G768 Install Pre-assembled Air Plenums in ANSI 23-inch Configuration, on page 17

•DLP-G769 Install Air Plenum for ONS 15454 M6 Shelf in ETSI Configuration, on page 19

Stop. You have completed this procedure.

DLP-G766 Install Air Plenum for ONS 15454 M6 Shelf in ANSI 19-inch Cabinet

This task installs the air plenum for the ONS 15454 M6 shelf in ANSI 19-inch cabinet.Purpose

Installing the ONS 15454 M6 Shelf

DLP-G766 Install Air Plenum for ONS 15454 M6 Shelf in ANSI 19-inch Cabinet

Tabla de contenidos

Otros manuales de Plataforma multiservicio de Cisco

Cisco

Cisco ONS 15454 Series Manual de usuario

Cisco

Cisco IP DECT 6800 Series Manual de usuario

Cisco

Cisco ONS 15454 SDH E1-75 Manual de usuario

Cisco

Cisco ONS 15454 Series Manual de usuario

Cisco

Cisco ONS 15600 Manual de usuario

Cisco

Cisco ONS 15454 SDH E1-75 Manual de usuario

Cisco

Cisco ONS 15540 ESPx Manual

Cisco

Cisco ONS 15454 Series Manual

Cisco

Cisco ONS 15454 Hoja de instrucciones

Cisco

Cisco ONS 15305 Manual de usuario

Manuales populares de Plataforma multiservicio de otras marcas

Banner

Banner SureCross DX99 FlexPower Series Manual de usuario

VeEX

VeEX eCPRI Manual de usuario

Vestil

Vestil FTLP Series Manual de usuario

ATD Tools

ATD Tools ATD7341 Instrucciones de uso

Calix

Calix E7-20 Manual de usuario

Vestil

Vestil WP Series Manual de usuario

Bosch

Bosch XDK Manual de usuario

TEUPEN

TEUPEN LEO 23 GT Manual de usuario

Juniper

Juniper NFX350 Manual de usuario

Vestil

Vestil WP Series Hoja de especificaciones

Airo

Airo XS Series Manual de usuario

Siemens

Siemens RUGGEDCOM RX1400 Manual de usuario

Siemens

Siemens SIMATIC NET RUGGEDCOM MX5000 Manual de usuario

PASCO

PASCO ME-6834 Manual de usuario

Parker

Parker P2M Node 24 DO Manual de usuario

Infinera

Infinera ATN Instrucciones de funcionamiento e instalación

Belden

Belden grass valley GV NODE Manual de usuario

ENCARDIO RITE

ENCARDIO RITE EWN-01D Manual de usuario