Cisco 730 Manual de usuario
Your Headset
•What's in the Box, on page 1
•How to Wear Your Headset, on page 2
•Download and Set Up the Cisco Headsets app on Your Mobile Device, on page 3
•Turn Your Headset On and Off, on page 4
•Headset Connection, on page 5
•Headset Power, on page 10
•Voice Assistant, on page 12
•About Audio Notifications, on page 13
What's in the Box
Your Cisco Headset 730 comes with the following accessories:
• Cisco Headset 730
• Hard case
Your Headset
1
• USB Adapter
• USB-A to USB-C cable
• 3.5 mm cable
How to Wear Your Headset
Adjust your headband so that your headset fits comfortably on your head. Make sure the headset microphones
are positioned forward.
Your Headset
2
Your Headset
How to Wear Your Headset
Download and Set Up the Cisco Headsets app on Your Mobile
Device
Cisco Headsets is a mobile app that lets you update, control, and customize your headset from any iPhone or
Android mobile device. You can upgrade your headset, adjust your noise cancellation levels, change your
equalizer settings, and manage your headset notifications all from the app interface.
Procedure
Step 1 On your mobile device, open your preferred app store and download Cisco Headsets.
Step 2 Open Cisco Headsets and follow the app set-up instructions.
Your Headset
3
Your Headset
Download and Set Up the Cisco Headsets app on Your Mobile Device
Turn Your Headset On and Off
The Power/Bluetooth switch is located on the back of the left ear cup.
Procedure
Step 1 Slide the Power/Bluetooth switch up to turn on the headset.
Step 2 Slide the Power/Bluetooth switch down to turn off the headset.
It takes about 5 seconds for the headset to fully power down.
Note
Your Headset
4
Your Headset
Turn Your Headset On and Off
Headset Connection
Connect Your Headset to a Bluetooth Device
Put your headset into pairing mode to make it discoverable to other devices. Your Cisco Headset 730 can
save up to eight different Bluetooth devices and maintain simultaneous connections with up to two devices
at once.
If you already have two active Bluetooth sources, you must disconnect one before you can save another
Bluetooth device to your headset.
Note
You can also follow the prompts in the Cisco Headsets app when you connect your headset to your mobile
phone.
Procedure
Step 1 Slide up and hold the Power/Bluetooth switch for two seconds until the Bluetooth LED blinks.
Step 2 Enable Bluetooth on your device.
You can enable and disable Bluetooth from the Settings menu on most call devices.
Step 3 Select your headset from the device list.
Your headset will appear in the device list as Cisco HS 730 followed by the last three digits of your headset
serial number.
Related Topics
Your Headset Serial Number
Your Headset
5
Your Headset
Headset Connection
Bluetooth LED
The Bluetooth LED is located on the back of the left ear cup at the top of the Power/Bluetooth switch and
shows your headset connection status.
Table 1: Bluetooth LED Status
System StateLight Status
Successful Bluetooth connection
Solid blue, then off
Headset in Pairing Mode
Blinks blue
Manage Your Bluetooth Connections in the Cisco Headsets App
You can use the Cisco Headsets mobile app to manage your headset Bluetooth connections. Your headset can
save up to eight Bluetooth devices and maintain an active connection with two at the same time.
Procedure
Step 1 On your mobile device, open the Cisco Headsets app.
Step 2 Tap Connected to at the bottom of the home screen.
Step 3 Select the device you wish to connect or disconnect.
Use the USB Adapter
Your Cisco Headset 730 comes with a USB adapter for use with call devices that don't have a Bluetooth
option. The USB Adapter comes out of the box pre-paired to your headset. The adapter automatically connects
to your headset when it plugs into a powered USB port.
When you connect the USB Adapter, the LED blinks and then turns solid when it connects to your headset.
If your headset is unavailable to connect, the LED shuts off.
When you want to disconnect your headset, simply unplug the adapter from the call device. It takes about 10
minutes for your headset to accept another active Bluetooth connection after you disconnect the USB Adapter.
You can also turn off your headset then on again to pair a new device quickly.
Your Headset
6
Your Headset
Bluetooth LED
You can't install firmware updates to your headset through the USB Adapter.
Note
Procedure
Step 1 Plug in your USB Adapter to your preferred device.
Step 2 Turn on your Cisco Headset 730.
Step 3 On your device, select Cisco HS USB Adapter from the Bluetooth device list.
Pair the USB Adapter to Your Headset
You can re-pair your USB Adapter if you have erased your headset Bluetooth pairings or need to replace your
adapter.
Procedure
Step 1 Connect the USB Adapter to your chosen device.
Step 2 Use a pen or a paper clip to press down the Pairing button on the USB Adapter for four seconds. The blue
LED on top of the adapter blinks when it enters pairing mode.
Step 3 On your headset, slide and hold the Power/Bluetooth switch for two seconds. The adapter and your headset
pair automatically. The LED on top of the adapter shows solid blue when it connects.
Table 2: USB Adapter LED Status
Adapter StatusUSB LED
The USB Adapter is connected to the headset.The LED shows solid
blue.
The USB Adapter is in pairing mode.The LED flashes blue.
The USB Adapter can't find a saved headset. Your headset automatically pairs
to the adapter when it turns on and has less than two active Bluetooth connections.
If you have erased all Bluetooth pairings from your headset, put the adapter and
your headset into pairing mode to reconnect them.
The LED flashes for 10
seconds and turns off.
Your Headset
7
Your Headset
Pair the USB Adapter to Your Headset
Alternate Between Active Bluetooth Sources
You can connect up to two Bluetooth devices to your headset at one time. Active calls are automatically placed
on hold when you answer a call on a different source.
Procedure
To change your Bluetooth source, play music or answer a call on a different connected source.
Pause music playback before you switch to a different music source.
Note
Delete Paired Devices
You can erase all paired Bluetooth devices from your headset.
This will also erase the USB Adapter from your headset's memory. See Pair the USB Adapter to Your Headset,
on page 7 to re-pair the adapter to your headset.
Note
Procedure
Slide and hold the Power/Bluetooth switch for nine seconds. If audible notifications are enabled, your headset
plays an audio prompt when it erases all Bluetooth devices.
Your Headset
8
Your Headset
Alternate Between Active Bluetooth Sources
Use the USB-C Cable
Use the included USB-C cable to connect your headset with your laptop, Cisco IP Phone, or Cisco Webex
DX device.
Procedure
Step 1 Plug the USB-C cable into the port at the bottom of the left ear cup.
Step 2 Connect the other end of the cable to your intended device.
Step 3 Slide the Power/Bluetooth slider up to turn on the headset.
Use the 3.5 mm Audio Cable
Use the included 3.5 mm audio cable to connect your headset with your laptop or mobile device. You can use
the audio cable to connect to a non-wireless device or if your headset battery is low.
You can't control calls or music playback when you use the 3.5 mm cable. Any connected Bluetooth sources
will have priority over the 3.5 mm audio connection.
Note
Procedure
Step 1 Plug the 3.5 mm audio cable into the port at the bottom of the left ear cup.
Your Headset
9
Your Headset
Use the USB-C Cable
Step 2 Insert the other end of the cable into the 3.5 mm jack on your device.
Headset Power
Check Your Remaining Battery Life
When you power on your headset, a voice notification announces your remaining battery charge. Your headset
notifies you when you have less then an hour of talk time remaining.
Voice notifications are turned on by default. You can toggle your headset voice notifications in the Cisco
Headsets mobile app.
Note
You can find more detailed battery charge information through the Cisco Headsets app.
Procedure
Slide the Power/Bluetooth switch up and let go.
• If you are wearing your headset, you can hear how many hours of talk time remain.
• If you are not wearing the headset, the power LED blinks to show your battery level.
Your Headset
10
Your Headset
Headset Power
Otros manuales para 730
3
Tabla de contenidos
Otros manuales de Auriculares de Cisco
Cisco
Cisco 500 Series Manual de instrucciones
Cisco
Cisco Cisco Headset 561 Manual de usuario
Cisco
Cisco Aironet 521 Manual de usuario
Cisco
Cisco Cisco Headset 561 Manual de usuario
Cisco
Cisco Jawbone ICON Manual de usuario
Cisco
Cisco 500 Series Manual de usuario
Cisco
Cisco 730 Manual de usuario
Cisco
Cisco 500 Series Guía
Cisco
Cisco Headset 530 Series Manual de usuario
Cisco
Cisco 232D Manual de usuario
Cisco
Cisco 500 Series Manual de usuario
Cisco
Cisco 730 Manual de usuario
Cisco
Cisco 730 Manual de usuario
Cisco
Cisco 700 series Manual de instrucciones
Cisco
Cisco Headset 560 Series Manual de usuario
Cisco
Cisco 500 Series Manual de usuario
Cisco
Cisco 531 Manual de usuario
Cisco
Cisco Cisco Headset 562 Manual de usuario
Cisco
Cisco Cisco Headset 561 Manual de usuario
Cisco
Cisco 520 Series Manual de usuario
