Christie Solaria One Manual de usuario

Retrofitting the Solaria

One projector with a

Dolby IMS3000 IMB

This document describes the steps for installing an integrated media block (IMB) faceplate retrofit kit,

allowing the use of the Dolby IMS3000 third party IMB in Solaria One series projectors.

Affected products

These instructions apply to the following products

• Christie Solaria One

• Christie Solaria One+

Prerequisites

The following components are required to complete the installation.

• 003-109982-01 Kit Solaria IMS3000, containing the following components:

• Faceplate (QTY: 1)

• EMI gaskets (QTY: 2)

• IMS3000 support bracket (QTY: 1)

• Void warranty label (QTY: 1)

• Electrostatic discharge bag (QTY: 1)

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 1

020-103421-02 Rev. 1 (11-2020)

Required tools

The following tools are required to complete the installation.

•Electrostatic discharge mat

• Grounded electrostatic discharge wrist strap

• #1 Phillips® screwdriver

• #2 Phillips® screwdriver

• 14 mm wrench

• Ratchet with the following nut drivers:

• 3/16 nut driver

• 5/8 nut driver

• 7/32 nut driver

• 2.5 mm hex driver

• Pliers

Safety precautions

To prevent personal injury and to protect the product from damage, review these important safety

precautions.

Warning! If not avoided, the following could result in death or serious injury.

• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,

removing components, or opening any enclosure.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 2

020-103421-02 Rev. 1 (11-2020)

Caution! If not avoided, the following could result in minor or moderate injury.

• Only Christie qualified technicians are permitted to open product enclosures.

• Observe all electrostatic precautions. Use a grounded wrist strap and insulated tools when

handling, servicing, or cleaning electronic assemblies.

Upgrading the projector software

Before installing the faceplate kit, upgrade the projector software to Solaria Main Software v4.8.1(3).

1. On the touch panel controller (TPC), select Menu > Administrator Setup > Upgrade.

2. Select Upload.

3. Browse to the location of the software upgrade file.

4. Select the upgrade file and select Open.

5. In the Available Upgrade Files list, select the upgrade file loaded in the previous step.

6. Select Next.

7. To upgrade all components in the upgrade package, select Upgrade Different Components

Only (Recommended).

8. Select Next.

Turning off the projector

Before removing the card cage, turn off the projector and disconnect it from AC power.

1. To turn off the lamp, select and hold the lamp button on the touch panel controller (TPC).

2. To turn off the projector, select and hold the power button on the TPC.

The projector enters cool down mode.

3. Allow the lamp to cool for a minimum of 10 minutes.

4. Unplug the AC power cable from the projector.

Disassembling the card cage faceplate and

board assembly

Complete the following procedure to remove the faceplate and board assembly from the projector and

take apart the components.

1. Place the electrostatic discharge mat on a clean flat surface.

2. Put on the grounded electrostatic discharge wrist strap.

3. Cut the void warranty label.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 3

020-103421-02 Rev. 1 (11-2020)

4. Using a #2 Phillips® screwdriver, remove the eight screws securing the card cage faceplate to

the card cage. Set the screws aside.

5. Using the two handles, pull the card cage faceplate assembly out of the card cage.

6. Place the assembly on the electrostatic discharge mat as shown.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 4

020-103421-02 Rev. 1 (11-2020)

7. Using a 14 mm wrench or deep socket, remove the GEN Lock, Sync Out, and LTC Out nuts. Set

the nuts and washers aside.

8. Using a 3/16 nut driver, remove the two nuts on either side of the AES3 output. Set the nuts

aside.

9. Using a 2.5 mm ball hex driver, remove the left screw securing the Christie IMB to the

faceplate. Set the screw aside.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 5

020-103421-02 Rev. 1 (11-2020)

10. Rotate the assembly 180 degrees.

11. Using a 2.5 mm ball hex driver, remove the right screw securing the Christie IMB to the

faceplate. Set the screw aside.

12. Using a 2.5 mm hex driver, remove the two screws on the bottom of the PIBS1 board. Set the

screws and support bracket aside.

13. Carefully separate the Christie IMB from the faceplate. Set the Christie IMB aside.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 6

020-103421-02 Rev. 1 (11-2020)

14. Using a 3/16 nut driver, remove the 3D Sync, RS 232 PIBS1, HDMI A/LEFT, and HDMI B/RIGHT

nuts. Set the nuts aside.

15. Disconnect the harness from the PIB faceplate board.

16. Using a #1 Phillips® screwdriver, remove the two screws securing the PIBS1 board to the

faceplate. Set the screws aside.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 7

020-103421-02 Rev. 1 (11-2020)

17. Carefully separate the PIBS1 board from the faceplate. Set the board aside.

18. Using a 7/32 nut driver, remove the four nuts securing the PIB faceplate board to the faceplate

and remove the PIB faceplate board and four spacers. Set the nuts, board, and spacers aside.

19. Using a #1 Phillips® screwdriver, remove the four screws securing the handles to the faceplate.

Set the handles and screws aside.

20. Remove the EMI gasket and set it aside.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 8

020-103421-02 Rev. 1 (11-2020)

Installing the faceplate kit

Complete the following procedure to install the Dolby IMS3000 IMB to the Solaria One faceplate

provided in the conversion kit.

1. Place the Dolby IMS3000 IMB and included parts on the electrostatic discharge mat.

2. Insert the EMI gasket tabs through the holes on the sides of the conversion kit faceplate.

3. Pull the long flange of the EMI gasket over the edge of the faceplate.

4. Place the four white spacers set aside in step 18 of the disassembly procedure onto the

threaded inserts on the faceplate.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 9

020-103421-02 Rev. 1 (11-2020)

5. Secure the PIB faceplate board to the faceplate using the four nuts set aside in step 18 of the

disassembly procedure. Torque the nuts to 10 in-lb.

6. Install the EMI gasket provided with the Dolby IMS3000 to the faceplate, as shown.

Retrofitting the Solaria One projector with a Dolby IMS3000 IMB

Installing the Christie Solaria One IMS3000 IMB Faceplate Kit Instruction Sheet 10

020-103421-02 Rev. 1 (11-2020)

Otros manuales para Solaria One

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Proyector de Christie

Christie

Christie CP2309-RGB Instrucciones de montaje

Christie

Christie DS+650 Manual de usuario

Christie

Christie CP2308-C Manual de funcionamiento

Christie

Christie LX55 Manual de usuario

Christie

Christie Mirage WQ-L Manual de usuario

Christie

Christie D4K35 Manual de usuario

Christie

Christie HAL Series Manual de usuario

Christie

Christie 38-VIV403-01 Manual de usuario

Christie

Christie LW650 Manual de usuario

Christie

Christie Roadster Manual de usuario

Christie

Christie DWU760-iS Instrucciones de montaje

Christie

Christie LX1500 Manual de usuario

Christie

Christie TruLife+ Griffyn 4K32-RGB Instrucciones de montaje

Christie

Christie D13WU2-HS Manual de usuario

Christie

Christie Vivid WHITE 38-VIV401-01 Manual de usuario

Christie

Christie LX501 Manual del propietario

Christie

Christie DWU951 Manual de usuario

Christie

Christie CP2308 Manual de usuario

Christie

Christie D4KLH60 Mirage 4KLH Manual de usuario

Christie

Christie Q Series Manual de usuario

Christie

Christie Cinema 4K-RGB CP4315-RGB Manual de usuario

Christie

Christie Solaria CP2210 Manual de usuario

Christie

Christie LX400 Manual de usuario

Christie

Christie APS Series Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario

Asus

Asus ZenBeam Latte Manual de usuario