Christie Roadster Manual de usuario

Boresight Alignment Procedure Instruction Sheet 1 of 3

020-100116-01 Rev. 1 (11/07)

Boresight Alignment Procedure

Instruction Sheet

INTRODUCTION

The following instructions outline Boresight Adjustment on any Roadster, Mirage, Matrix, DLV,

Christie DS and Christie DW model projector.

Boresight alignment ensures the projection lens is precisely parallel with the exit-face of the prism and

that the correct distance exists between the exit face and the input of the projection lens. Typically, this

procedure is performed whenever a lens mount is replaced to ensure the displayed image has optimum

focus in all four corners and the center.

NOTICE: Projectors must be serviced in a clean environment to prevent dust particles from settling on

optical components.

TOOLS REQUIRED

Lens cap with pinhole in center (Recommended, but not necessary).

WARNINGS

Replacement must be performed by qualified Christie service personnel only.

Observe all electrostatic precautions.

2 of 3 Boresight Alignment Procedure Instruction Sheet

020-100116-01 Rev. 1 (11/07)

INSTRUCTIONS

NOTE: For DLV1400-DX and DLV1920-DX models, refer to Boresight Alignment for Fixed Lens

Mount Models, on page 3.

1. Set the spacing behind screws 1a, 2a, 3a and 4a

to 4mm. Refer to Figure 1.

2. Load the “GRID” internal test pattern (Figure

2).

3. Using the IR keypad, use to enable

the green only.

4. Focus the lens on the screen at the correct size

for the throw ratio of the lens (approximately

center of focus range). See Figure 2. For 0.73

lenses only, set the focus adjustment ring to

mid-range.

5. Ensure the projected image is perfectly square

on the wall with no visible horizontal or vertical

keystone. If vertical keystone is observed, adjust the projector’s feet until it is level and the image

appears rectangular.

6. Adjust the horizontal and vertical lens offsets

until the image is centered in the lens (Figure

3). NOTE: Use a lens cap with a pinhole in the

center or hold a sheet of paper in front of the

lens and then center the image.

Figure 1 Boresight Adjustment Screws

Func

Figure 2 Grid Test Pattern

Figure 3 Offset Adjustment

Boresight Alignment Procedure Instruction Sheet 3 of 3

020-100116-01 Rev. 1 (11/07)

You are now ready to perform a precision boresight alignment on the projector to achieve the best

possible uniform focus.

1. Back off each corner locking screw (1b, 2b, 3b, & 4b) - refer to Figure 1).

2. Observe which portion of the image is out of focus. For example if the top left corner of the image

is out of focus than you will need to adjust screw 3a until that point is correctly focused (see Grid

Test Patterrn at right).

3. Then, observe the bottom right corner of the image, which will now be out of focus. Adjust screw

1a to correctly focus that point. NOTES: 1) You will have to alternate adjustments to both screws

until both points come into focus (or fairly close to focus). 2) Observe the opposite corners while

performing these adjustments as those opposite corners may come into focus as you are adjusting

the first 2 corners.

4. Adjust screw 2a until the top right corner is in focus.

5. Adjust screw 4a until the bottom left corner is in focus.

All four corners plus the center should now be correctly focused. NOTE: If the alignment process

causes the image to shift side-to-side or up and down by more than a few inches, re-center the image

using the lens cap with pinhole. Adjust the horizontal and vertical offsets to bring the image back to

the center. The image may have to be checked and re-centered a few times throughout this procedure.

BORESIGHT ALIGNMENT FOR FIXED LENS MOUNT DLV1400-DX AND

DLV1920-DX MODELS

When aligning boresight on the DLV model prjector, ensure the points below are observed:

• Use a 1.2:1 fixed lens.

• Focus the image as outlined in the steps above.

Otros manuales para Roadster

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Proyector de Christie

Christie

Christie Q Series Guía del usuario

Christie

Christie DWU951 Manual de usuario

Christie

Christie CP2309-RGB Instrucciones de montaje

Christie

Christie LX501 Guía de inicio rápido

Christie

Christie M Series Manual de usuario

Christie

Christie Projector Manual de usuario

Christie

Christie 38-VIV210-01 Manual de usuario

Christie

Christie LX700 Manual de usuario

Christie

Christie DWU951 Manual de usuario

Christie

Christie LWU620i Manual de usuario

Christie

Christie Solaria CP2210 Manual de usuario

Christie

Christie J Series Manual de usuario

Christie

Christie E Series Manual de usuario

Christie

Christie L2K1000 Manual de usuario

Christie

Christie Q Series Manual de usuario

Christie

Christie 1000W J Series Manual de usuario

Christie

Christie 103-002001 Manual de usuario

Christie

Christie DWU951 Manual de usuario

Christie

Christie CP2000-XB Manual de usuario

Christie

Christie E Series Manual de usuario

Christie

Christie DLV1280 DX Manual de usuario

Christie

Christie CP2308 Manual de usuario

Christie

Christie M Series Manual de usuario

Christie

Christie Mirage 2000 Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario

Asus

Asus ZenBeam Latte Manual de usuario