Christie One Manual de usuario
Assembling the Christie
One aluminum rigging
frame
With the Christie One aluminum rigging frame (P/N: 140-137102-01), the projector can be secured to
trusses or structures built for the purpose of positioning the projector.
With the frame:
• Up to three projectors can be stacked in landscape orientation.
• A single projector can be positioned in portrait mode but no stacking is permitted.
Christie ships the frame separately from the projector.
Affected products
The Christie One rigging frame is designed for use with the following projectors.
• HS Series projectors (D13WU-HS, D13HD-HS, D16WU-HS, D16HD-HS, D20WU-HS, D20HD-
HS, 4K7-HS, and 4K10-HS)
Safety warnings and guidelines
Read all safety and warning guidelines before starting this procedure.
Danger! If not avoided, the following results in death or serious injury.
• Do not stack the device unless specified in this manual.
• The supporting structure must safely support the combined load of the product, all attached
hardware, and components following all local safety standards and regulations.
• Use all mounting points, including the safety point, when installing the product overhead.
Warning! If not avoided, the following could result in death or serious injury.
• Only use this frame with the specified products.
• Safety straps must be used when stacking two or more rigging frames.
• Always install safety straps when the frame and projector are installed overhead.
• Do not stack empty frames.
• Projectors must be installed in frames before stacking.
Notice. If not avoided, the following could result in property damage.
• Use appropriate packaging when shipping the product installed in the frame.
Assembling the Christie One Frame Instruction Sheet 1
020-103043-01 Rev. 1 (05-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.
Tools required
The following tools are required for installing the rigging frame.
• 6 mm hex key
Optional tools
• Adjustment tool provided with the Christie One aluminum rigging frame
Physical specifications
Learn the weight and physical dimensions of the Christie One rigging frame.
• Weight: 30 kg (66 lbs)
• Dimensions: 850 x 756 x 466 mm (H)
Securing the projector to the stacking frame
Secure the projector to the stacking frame before stacking additional projectors.
Danger! If not avoided, the following results in death or serious injury.
• TIP HAZARD! Stacked frames must be secured together using all locking pins.
• Use all mounting points, including the safety point, when installing the product overhead.
Warning! If not avoided, the following could result in death or serious injury.
• A minimum of four people or appropriately rated lift equipment is required to safely lift, install,
or move the product.
• The supporting structure must safely support the combined load of the product, all attached
hardware, and components following all local safety standards and regulations.
1. Turn off the projector.
Allow the cooling fans to stop before proceeding with step 2.
2. Disconnect the projector from AC power.
3. Remove the lens from the projector, if installed.
4. Verify the base plate of the frame is in a flat position and is level.
5. Adjust the feet of the projector.
• Ensure the feet of the projector do not extend.
The projector must sit flat on the base plate.
Assembling the Christie One aluminum rigging frame
Assembling the Christie One Frame Instruction Sheet 2
020-103043-01 Rev. 1 (05-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.
6. Place the four spacers provided with the frame over the four HS Series mounting holes on top
of the base plate.
Ensure the holes on the base plate and spacers are aligned.
7. Insert HS Series projectors through the front of the frame.
Ensure the lens mount faces the front of the frame, as indicated below.
8. Secure the projector to the base plate using four hex socket head screws and washers
provided with frame.
• For D13WU-HS, D13HD-HS, D16WU-HS, D16HD-HS, D20WU-HS, and D20HD-HS) series
projectors, use four M8 x 1.25 x 30 mm bolts and washers and secure with a 6 mm hex
key.
For 4K7-HS and 4K10-HS series projectors, use seven M8 x 1.25 x 20 mm bolts and
washers and secure with a 6 mm hex key.
The M8 bolts must be tightened to a torque of 38 Nm.
Refer to the image below for the mounting points on the base plate for each projector series.
Assembling the Christie One aluminum rigging frame
Assembling the Christie One Frame Instruction Sheet 3
020-103043-01 Rev. 1 (05-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.
Stacking multiple framed projectors
Up to three framed projectors can be stacked in landscape orientation only, and then rigged in an
upright or inverted position. Stacking in portrait orientation is not permitted.
Danger! If not avoided, the following results in death or serious injury.
• TIP HAZARD! Stacked frames must be secured together using all locking pins.
• Do not stack the device unless specified in this manual.
Warning! If not avoided, the following could result in death or serious injury.
• A minimum of four people or appropriately rated lift equipment is required to safely lift, install,
or move the product.
• The supporting structure must safely support the combined load of the product, all attached
hardware, and components following all local safety standards and regulations.
• Do not stack empty frames.
• Projectors must be installed in frames before stacking.
1. Remove the locking pins from each stacking leg.
2. With one person positioned on each side of the framed projector, lift the assembly and place it
onto the bottom frame.
Stacking in portrait orientation is not permitted
3. Verify the four stacking legs of the upper assembly are securely seated on the bottom frame.
4. Insert a locking pin through each of the stacking legs to lock the frames together.
The steel ball on the end of the pin keeps the pin from releasing inadvertently.
5. Install safety straps (not included) for each leg of the frame between the frames.
Safety straps must be adequately rates for the total load.
Assembling the Christie One aluminum rigging frame
Assembling the Christie One Frame Instruction Sheet 4
020-103043-01 Rev. 1 (05-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.
6. When stacking a third framed projector, repeat steps 1 to 4.
Aligning stacked projectors
Stacked projectors must be correctly aligned to one another to achieve an optimally displayed image.
1. Hoist and secure a stack of projectors before aligning.
2. Loosen the locking screws on each adjustment knob.
3. Before adjusting the roll, loosen the four screws on the base plate; otherwise, the adjustment
knob can break during adjustment.
4. Adjust pitch, roll, or yaw, manually or with the optional adjustment tool provided with the
frame, until the image geometry is optimized.
Assembling the Christie One aluminum rigging frame
Assembling the Christie One Frame Instruction Sheet 5
020-103043-01 Rev. 1 (05-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.
A and B Roll—Rotates the image clockwise or counter-clockwise.
Pitch—Moves the image up and down.
C Yaw—Moves the image to the left or right.
5. For pitch and yaw, ensure the gap between the pin and the plate is more than 0.5 mm.
The pin limits the adjustment within the useful range.
6. To lock adjustments, tighten the setscrews on each adjustment knob.
Assembling the Christie One aluminum rigging frame
Assembling the Christie One Frame Instruction Sheet 6
020-103043-01 Rev. 1 (05-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios para proyectores de Christie
Christie
Christie Vivid Blue 38-VIV301-01 Manual de usuario
Christie
Christie 118-131106 Series Manual de usuario
Christie
Christie DPS Series Manual de funcionamiento
Christie
Christie LX32 Guía
Christie
Christie Brio Manual de usuario
Christie
Christie P100 Manual de usuario
Christie
Christie 140-133108 Series Manual de usuario
Christie
Christie ChristieNet Wireless Presentation Portal Manual de usuario
Christie
Christie QwikRig Rigging Frame V2 Manual de programación
Christie
Christie Brio Manual de usuario
Christie
Christie D4K40-RGB Manual de uso y cuidado
Christie
Christie LX380 Manual de usuario
Christie
Christie Dual LOS Manual de usuario
Christie
Christie CIC Instrucciones de montaje
Christie
Christie One Manual de usuario
Christie
Christie 163-126100 Series Manual de usuario
Christie
Christie Christie One Mount Manual de instrucciones
Christie
Christie 003-006191-01 Manual de usuario
Christie
Christie Brio Enterprise Manual de usuario
Christie
Christie QwikRig rigging frame Manual de usuario
