Chore-Time Hyflo 53096-52 Guía de configuración
36" Galvanized Belt Drive HYFLO® Fans
Installation and Operators Instruction Manual Fan
Part No. 53096-52
z
Fan and Fan Framing Dimensions
MV1747-017 04/03
4
Planning the layout of the spacing between Fans is very
important. Spacing too close together will cause
interference between the discharge Cones. The Rough
Opening dimensions for Fans are shown above.
6
3
1
2
7
Item Description Dimension
1 Bottom Length 41-1/2'' [105.41cm]
2 Vertical Dim. of Cone 1'' [2.54cm]
3 Height (Outside of Flanges) 45-1/2" [115.57cm]
4 Rough Opening Width 43" [109.22cm]
5 Rough Opening Height 42-1/2 [107.95cm]
6 Minimum Spacing 3-1/2" [8.89cm]
7 Outside Diameter of Cone 43-3/4" [111.13cm]
8 Depth inside Building 6-1/2" [16.51cm]
Figure 1. Fan Dimensions
5
8
The Fan Inlet and exhaust must be kept clear of obstructions. Failure to keep the Fan airflow path
clear of obstructions could cause loss of Fan performance and Fan damage.
MV2386E
April 2018
Do Not operate these Fans with a variable speed control device. Operating static pressure should be less
than 0.15 inches water column [37.4 pascal].
Fan Assembly/Installation
Fan Assembly/Installation 36" Galvanized Belt Drive HYFLO® Fans
2MV2386E
Screen Clips
Set the Fan into the framed opening, but leave it hang out a few inches to allow for the insertion of four
Screen Clips (Item 1, Figure 7). With the Screen Clips oriented with the tab lock as shown, push them into
the slots in the Fan Housing Panels and rotate them forward until they lock into place as shown. Slide the
Fan forward flush with the rough opening making sure that the Clips do not fall out.
Item Description
1 Screen Clip
Step 1: Set Fan into Rough opening Step 3: Rotate Screen Clip to
lock into place
forward
Step 2: Insert Screen Clip into slot
1Orient Screen Clip
Tab Lock
with tab lock as shown
Step 4: Repeat Steps 1 through 3 for the bottom
Screen Clips
Figure 7. Installing Screen Clips
36" Galvanized Belt Drive HYFLO® Fans Fan Assembly/Installation
MV2386E 3
Attaching the Fan to the Wall
Slide the Fan assembly into the rough opening and starting with the side hole locations (Detail A), use 1/4
x 1-3/4" Lag Screws (Item 1, Figure 8), two Nylon Washers (Item 2), and a Screen Retainer (Item 3) to
attach the Fan to the Wall as shown. Use 1/4 x 1-3/4" Lag Screws to attach the Fan at the four
corners (Detail B) as shown.
3
3
Figure 8. Attaching the Fan to the Wall
Corner Hole Detail "B"
Center Hole Detail "A"
A
B
A
B
31
2
3
1
Key Description
1 1/4 x 1-3/4 SS Lag Screw
2 Nylon Washer
3 Screen Retainer
BB
A
A
Motor Installation
Rotate the Motor Support Bracket into the upright position by removing the Upper Carriage Bolt and Nut
and loosening the Lower Bolt and Nut (See Figure 9). Rotate the Motor Support Bracket until it is
perpendicular to the Fan Posts and fasten with (4) 5/16 Carriage Bolts and (4) 5/16 Flange Nuts. Note that
the Nuts go outside the Posts. Remove the Motor from the Crate and attach it to the Motor Support Bracket
with (4) 5/16 Carriage Bolts and (4) 5/16 Flange Nuts as shown.
Figure 9. Attaching the Motor Support Bracket and Motor
Item Description
1 Motor Support Bracket
2 5/16 Carriage Bolt
3 5/16 Flange Nut
Lower Nut and Bolt
Hidden by Fan Post
3
2
3
1
3
3
3
323
3
3
2
3
2
Upper
Fan Assembly/Installation 36" Galvanized Belt Drive HYFLO® Fans
4MV2386E
Belt Installation
Guide the Belt through the Opening in the Motor Support Bracket and loop it over the Motor Sheave. Guide
the Belt around the Tensioner Sheave and push on it to get enough slack to put the Belt on the Driven Sheave
as shown in Figure 10. Make sure the Belt does not rub against the Motor Support Bracket.
3
Item Description
1Belt
2 Motor Sheave
3 Tensioner Sheave
4 Driven Sheave
1
3
2
4
Figure 10. Installing the Belt
Cone Assembly and Installation
Figure 11. Assembling Cone Panels
Slots in Cone Panel
C-Shaped Drain Tab
3
1
Item Description
1 Cone Panel
Wrong! Cone Panel is upside down
Lay a Cone Panel down (Drain Tab at the bottom and slots to the left) and Prop the end
up (Slotted end) with a 2 x 4 board.
Step 1:
Figure 12. Assembling Cone Panels
All Four Cone Panels Connected
Holes Nearest Cone Panels Edge
Insert the Tabs of a second Cone Panel into the slots of the 1st
Panel and Lay it down locking the two Panels together.
Repeat Step 2 until all four Cone Panels
are locked together.
Fasten the Cone Panels together with (4) 5/16" x 1/2" Hex Bolts
threaded from inside the finished Cone. Do not tighten down the
Nuts at this time. Leave the Nuts loose until the Cone is attached
to the Fan.
Stand the Panels up on edge and curl the Panels
around making a Cone shape with the smaller
diameter up. Insert the Tabs of the last Panel into the
Slots of the 1st and allow the Cone to take its shape.
Step 5:
Step 4:
Step 3:Step 2:
36" Galvanized Belt Drive HYFLO® Fans Fan Assembly/Installation
MV2386E 5
Fan Assembly/Installation 36" Galvanized Belt Drive HYFLO® Fans
6MV2386E
Installing Door Assembly
3
1
3
2
Figure 13. Installing the Door Assembly
Do not install Nuts
3
533
4
Line up the Four Holes in the Door Ring with the holes in the Cone and thread
(4) 5/16 x 1-1/4" Bolts (Item 3) in until they are tight. Do not install Nuts at this time.
These Bolts will be used later to attach the Cone Brackets to the Cone Assembly.
Use (2) 5/16 x 1-1/4" Bolts (Item 3) and (2) 5/16" Flange Nuts (Item 4) to attach the
Ring to the Cone using the holes located on both sides near the Door Center Brace
(Item 5) as shown. The Nuts go outside the Cone.
Item Description
1Tape
2 Nylon Cable
3 5/16 x 1-1/4" Bolt
4 5/16 Flange Nut
5 Door Center Brace
3
3
3
3
Remove Tape (Item 1) holding the Nylon Cable (Item 2) to the Door.
Step 1:
Step 2:
Step 3:
36" Galvanized Belt Drive HYFLO® Fans Fan Assembly/Installation
MV2386E 7
Attaching the Door Stop Cable (Nylon Cable) and Grill.
3
3
3
4
3
3
Line up the Grill Eyehooks with the holes in the Cone. Thread the free end of the Nylon
Cable (Item 2) through the bottom Grill Eyehook (Item 1) until it is flush with the Cone
and secure it with a 5/16-18 Carriage Bolt (Item 3) and Flange Nut (Item 4) as shown.
Item Description
1 Bottom Grill Eyehook
2 Door Stop Cable (Nylon Cable)
3 5/16-18 x .625 Carriage Bolt
4 5/16-18 Flange Nut
3
1
Figure 14. Installing the Door Stop Cable
3
2
3
4
Picture of Nylon Cable Secured
Use 5/16 Carriage Bolts (Item 3) and Nuts (Item 4) to
fasten Grill to Cone at remaining 7 locations.
Step 1:
Step 2:
Nylon Cable Flush
with Cone
Top of Door
Fan Assembly/Installation 36" Galvanized Belt Drive HYFLO® Fans
8MV2386E
Assembling the Cone to the Fan
Use 5/16 x 5/8" Carriage Bolts and 5/16 Flange Nuts to attach the four Cone Brackets to the Fan Shroud as shown
in Figure 15.
Figure 15. Attaching the Cone Brackets
Item Description
1 Cone Bracket
2 5/16 x 5/8" Carriage Bolt
3 5/16 Flange Nut
3
1
3
2
3
Mounting the Cone and Door Assembly on the Fan requires at least two people. Pick up and orient the Cone with
the Door Stop Cable (Item 1, Figure 16) attached at the top and rest the Cone on top of the Fan Orifice as shown.
Attach the top of the Cone to the Cone Brackets (Item 2) with the Bolts that were previously threaded through the
Ring and Cone and secure with 5/16 Flange Nuts (Item 3). Only hand tighten the Nuts at this time. Working around
the Fan Orifice from inside the fan, in a circular motion Slide the Cone over the Fan Orifice. The Cone will Fit snug.
Use the Bolts previously threaded through the Ring and Cone and the 5/16 Flange Nuts to secure the bottom of the
Cone to the Fan as shown. Use a Level and rotate the Cone until the Door center rail is Vertical (See Figure). Now
tighten all Hardware.
3
2
Cone resting on Fan Orifice
3
2
3
3
Item Description
1 Door Stop Cable
2 Cone Bracket
3 5/16 Flange Nut
Figure 16. Attaching the Cone
3
3
3
1
Door Center Rail Vertical
36" Galvanized Belt Drive HYFLO® Fans Fan Assembly/Installation
MV2386E 9
Door Spring Assembly
3
2
3
1
On the Door Assembly, at the middle
of the Door Center Brace, attach the
Spring Mounting Bracket (Included
in the Parts Package)
Step 1:
3
4
Hook the rounded ends of the Door
Springs onto the Spring Mounting
Bracket. Stretch the Door Springs out and
hook them in the 3/32" holes in the Doors.
Step 2:
Item Description
1 Door Center Brace
2 Spring Mounting Bracket
3 Door Spring
4 3/32" hole in Door
Figure 17. Attaching the Spring Mounting
3
3
Fan Assembly/Installation 36" Galvanized Belt Drive HYFLO® Fans
10 MV2386E
Cone Drain Tabs
The Fan Cone is designed with a C-Shaped Drain Tab located at the back of the Bottom Cone Panel. Use a screw
driver to push the Drain Tab out as shown in Figure 18 below.
Figure 18. Cone Drain Tab
Item Description
1Drain Tab
3
1
Tabla de contenidos
Otros manuales de Admirador de Chore-Time
Chore-Time
Chore-Time 50576 Especificaciones
Chore-Time
Chore-Time TURBO Especificaciones
Chore-Time
Chore-Time Endura 57" Fan Guía de configuración
Chore-Time
Chore-Time Vanguard plus 48318 series Manual de usuario
Chore-Time
Chore-Time MV1666B Manual de usuario
Chore-Time
Chore-Time Endura 57" Flush Mount Fan Manual de usuario
Chore-Time
Chore-Time Hyflo 50485 Especificaciones
Chore-Time
Chore-Time Hyflo Manual de usuario
Chore-Time
Chore-Time TURBO Especificaciones
Chore-Time
Chore-Time 27140-115 Manual de usuario
Chore-Time
Chore-Time 52 TURBO Especificaciones
Chore-Time
Chore-Time E-Z Manual de usuario
Chore-Time
Chore-Time TURBO Especificaciones
Chore-Time
Chore-Time 14843 Especificaciones
Chore-Time
Chore-Time TURBO MV1864P Guía del administrador
Chore-Time
Chore-Time MV1430J Especificaciones
Chore-Time
Chore-Time MV1600B Instrucciones de montaje
Chore-Time
Chore-Time Mv1680-001 Especificaciones
Chore-Time
Chore-Time TURBO series Guía del administrador
Chore-Time
Chore-Time PIGTEK PT5048 Manual de usuario
