Chicago Pneumatic Quiet CP7830Q Manual de usuario

Operator’s Manual

CP7830Q & CP7830HQ

3/8” & 1/2” Ratchet Wrench

To reduce risk of injury, everyone using, installing, repairing,

maintaining, changing accessories on, or working near this tool

must read and understand these instructions before performing

any such task.

WARNING

CP7830Q & CP7830HQ

3/8” & 1/2” Ratchet Wrench

INSTRUCTION MANUAL

Machine Type:

This product is designed for installing and removing threaded

fasteners in wood, metal and plastic. No other use permitted.

For professional use only.

Air Supply Requirements

1. Supply tool with 90 psig (6.2 bar) of clean, dry air. Higher

pressure drastically reduces tool life.

2. Connect tool to air line using pipe, hose and tting sizes

shown in the diagram below.

Lubrication

1. Use an air line lubricator with SAE #10 oil, adjusted to

two (2) drops per minute. If an air line lubricator cannot be

used, add air motor oil to the inlet once a day.

2. Monthly, lubricate the drive bushing and ratchet yoke with

a good grade bearing grease. Periodically, depending

upon use, the ratchet head assembly should be removed,

cleaned and re-greased.

Reducing sound level by rotation of exhaust

deector

The tool is packaged with the exhaust air slots aligned with

the trigger and square drive. Rotating the exhaust deector

will further reduce noise levels, with the lowest noise levels

at approximately 180° from the as-shipped position.

Maintenance

1. Tool should be oiled on a daily basis for best performance.

Every 3 to 6 months the tool’s head should be greased

using approved CP Gear Grease. If the tool loses

performance over time, tool should be sent to a CP

Certied Service Center to be checked and repaired as

needed.

2. High wear parts are underlined in the parts list.

3. To keep downtime to a minimum, the following service kits

are recommended:

Tune-Up Kit: see part list 8940169404

1/2" (12mm)

3/8" (10mm)

3/8" (10mm)

3/8" (10mm)

CA048361 (1/2")

CA048362 (1/2")

CA048360 (1/2")

3/8" (10mm)

3/8" (10mm)

130

90

0

Learn more about air tools and compressors on our website.

Otros manuales para Quiet CP7830Q

3

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Chicago Pneumatic

Chicago Pneumatic

Chicago Pneumatic RediPower RP9426 Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP749 Series Manual de usuario

Chicago Pneumatic

Chicago Pneumatic PT052-T7000-I10S Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP 2190 Guía de mantenimiento y servicio

Chicago Pneumatic

Chicago Pneumatic CP826 Manual de usuario

Chicago Pneumatic

Chicago Pneumatic MS 690 Guía de mantenimiento y servicio

Chicago Pneumatic

Chicago Pneumatic CP797 Series Manual de usuario

Chicago Pneumatic

Chicago Pneumatic MS 595 Guía de mantenimiento y servicio

Chicago Pneumatic

Chicago Pneumatic CP7763 Series Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP7828 Manual de usuario

Chicago Pneumatic

Chicago Pneumatic B20L Manual de usuario

Chicago Pneumatic

Chicago Pneumatic PT014-T6000-S4Q Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP7829H Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP826 Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP 550 Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP 1230 SPDR Guía de mantenimiento y servicio

Chicago Pneumatic

Chicago Pneumatic Erickson CP3109-19 Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP7830 Series Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP828 Series Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP7782 Series Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP7600 C Series Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic Quiet CP7830Q Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP785 Series Manual de usuario

Chicago Pneumatic

Chicago Pneumatic CP826 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual