Chicago Electric 95380 Manual de instalación

ROUTER TABLE WITH ROUTER

Model

95380

SET UP AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Manual Revised 11c

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 2

SPECIFICATIONS

Motor 110 VAC / 60 Hz / 11 A / 1-3/4 HP / 20,000 Maximum RPM

Router Type Plunge Router with Brake

Router Power Cord SJT 16 AWG x 2C

Router Table Power Switch Rocker (ON/OFF) with Safety Key

Router Table Power Cord 16 AWG 3C

Router Table Power Plug 3-Prong / Grounded

Router Collet Sizes 1/2” with 3/8” & 1/4” Adapters

Router Depth Scale 1” to 3” in 1/16” Increments

Miter Gauge Dimensions 5-1/2” Long x 3” Wide x 1-1/2” High

Miter Gauge Capacity 0° to 60° (Left & Right)

Table Dust Port Dimensions 1-3/8” Outside Diameter

Table Top Dimensions 14-3/8” Long x 23-3/4” Wide x 3/4” Thick

Overall Dimensions 14-13/16” Long x 23-3/4” Wide x 15-3/4” High

Additional Features 19 Gauge Steel Legs / Clear Plastic Guard

Weight 20 Pounds

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions,

assembly, operating, inspection, maintenance and cleaning procedures,

parts list and assembly diagram. Keep your invoice with this manual.

Write the invoice number on the inside of the front cover. Keep this

manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING! Read all instructions

Failure to follow all instructions listed below may result in electric shock,

re, and/or serious injury. The term “power tool” in all of the warnings listed

below refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

2. Do not operate the Router in explosive atmospheres, such as

in the presence of ammable liquids, gases, or dust. Power

equipment creates sparks which may ignite the dust or fumes.

3. Keep bystanders, children, and visitors away while operating power

equipment. Distractions can cause you to lose control. Protect others in

the work area from debris such as chips and sparks. Provide barriers or

shields as needed. Children and visitors should never be in the work area.

227847

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 3

ELECTRICAL SAFETY

1. Grounded tools must be plugged into an outlet properly installed

and grounded in accordance with all codes and ordinances. Never

remove the grounding prong or modify the plug in any way. Do

not use any adapter plugs. Check with a qualied electrician if you

are in doubt as to whether the outlet is properly grounded. If the

tools should electrically malfunction or break down, grounding provides

a low resistance path to carry electricity away from the user.

2. Avoid body contact with grounded surfaces such as

pipes, radiators, ranges, and refrigerators. There is an

increased risk of electric shock if your body is grounded.

3. Do not expose power tools to rain or wet conditions. Water

entering power equipment will increase the risk of electric shock.

4. Do not abuse the Power Cord. Never use the Power Cord to pull

the Plug from an outlet. Keep the Power Cord away from heat, oil,

sharp edges, or moving parts. Replace damaged Power Cords

immediately. Damaged Power Cords increase the risk of electric shock.

PERSONAL SAFETY

1. Stay alert. Watch what you are doing, and use common sense when

operating the Router. Do not use the tool while tired or under the

inuence of drugs, alcohol, or medication. A moment of inattention

while operating power tools may result in serious personal injury.

2. Dress properly. Do not wear loose clothing or jewelry. Contain long

hair. Keep your hair, clothing, and gloves away from moving parts.

Loose clothes, jewelry, or long hair can be caught in moving parts.

3. Use the right product for the job. Do not attempt to force small equipment

to do the work of larger industrial equipment. There are certain applications

for which this product was designed. It will do the job better and safer at

the rate and capacity for which it was designed. Do not modify this product,

and do not use this product for a purpose for which it was not designed.

4. Avoid accidental starting. Be sure the Power Switch is off before plugging

in. Plugging in power equipment with the Power Switch on, invites accidents.

5. Remove adjusting keys or wrenches before turning the

power tool on. A wrench or a key that is left attached to a

rotating part of the Router may result in personal injury.

6. Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the Router in unexpected situations.

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 4

7. Use safety equipment. Always wear ANSI-approved safety impact

eye goggles. Dust mask or respirator, and hearing protection must be

used for appropriate conditions.

TOOL USE AND CARE

1. Do not force the Router. Use the correct tool for your application. The

correct tool will do the job better and safer at the rate for which it is designed.

2. Do not use the Router if the Power Switch does not turn

it on or off. Any tool that cannot be controlled with the

Power Switch is dangerous and must be replaced.

3. Disconnect the Power Cord Plug from the power source before making

any adjustments, changing accessories, or storing the Router. Such

preventive safety measures reduce the risk of starting the tool accidentally.

4. Store idle tools and equipment out of reach of children and other untrained

persons. Tools and equipment are dangerous in the hands of untrained users.

5. Maintain this product with care. Keep the Router and its Table clean

and in proper working order. Properly maintained tools and equipment

are easier to control. Do not use damaged tools and equipment. Tag

damaged tools and equipment “Do not use” until repaired.

6. Check for misalignment or binding of moving parts, breakage

of parts, and any other condition that may affect the Router’s

operation. If damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained tools.

7. Use only accessories that are recommended by the manufacturer

for your model. Accessories that may be suitable for one product

may become hazardous when used on another product.

SERVICE

1. Tool service must be performed only by qualied repair personnel. Service

or maintenance performed by unqualied personnel could result in a risk of injury.

2. When servicing a tool, use only identical replacement parts. Follow

instructions in the “Inspection, Maintenance, And Cleaning”

section of this manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of electric shock or injury.

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 5

SPECIFIC SAFETY RULES

1. Maintain labels and nameplates on the Router and its Table.

These carry important information. If unreadable or missing,

contact Harbor Freight Tools for a replacement.

2. Avoid unintentional starting. Make sure you are prepared

to begin work before turning on the Router.

3. Do not force the Router. This tool will do the work better and

safer at the speed and capacity for which it was designed.

4. This Router is designed for use only with 1/2” Router Bits and

3/8” and 1/4” Adapters rated at 20,000 RPM or greater.

5. WARNING! Keep hands and ngers away from the cutting area and

Router Bit (not included). Use a “push stick” (not included) when necessary.

6. Make sure the Router Table is securely attached to a dry,

at, level, sturdy workbench surface capable of supporting

the weight of the unit, accessories, and workpieces.

7. Never leave the Router Table unattended when it is plugged into an

electrical outlet. Always unplug the unit from its electrical outlet before leaving.

8. Industrial applications must follow OSHA guidelines.

9. Never stand on the Router Table. Serious injury could result if the unit is tipped.

10. Always unplug the Router Table from its power supply source before

performing any inspection, maintenance, or cleaning procedures.

11. Keep all guards in place and in proper working order.

12. Allow the Router Bit (not included) to spin up to full speed before feeding

a workpiece into the Bit. When turning off the Router, allow the Bit to

spin down and stop on its own. Do not press against the Bit to stop it.

13. Turn off the Router and allow the Router Bit (not included) to stop on

its own if the workpiece is to be backed out of an uncompleted cut.

14. Never attempt to remove material stuck in the moving parts

of the Router while it is plugged in and running.

15. When routing a large workpiece, make sure its entire length is properly

supported. If necessary, use a roller stand (not included) with larger workpieces.

16. Never attempt to cut freehand. Make sure the workpiece

to be cut is pressed rmly against the Table’s Fence.

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 6

17. Never cut pieces too small to be held securely against the

Table’s Fence without leaving enough space for the hand to

be a safe distance from the Router Bit (not included).

18. Make sure the Table and surrounding area are clear

with the exception of the workpiece to be cut.

19. Before each use of the Router, make sure it is

securely attached to the Router Table.

20. The Router Table is designed for cutting at workpieces

only. Do not attempt to cut workpieces that are not at.

21. The Router and Router Table are designed for cutting

wood workpieces only. Do not attempt to use the Router

and its Table to cut metal or other non-wood materials.

22. Never attempt to cut more than one workpiece at a time.

23. Always make sure the work surface of the Router Table is

clean and free of dust, wood chips, and other debris that

can interfere with the cut you are going to make.

24. Always keep children and other unauthorized people away

from the Router Table. Unplug the Table, and remove the

Power Switch’s Safety Key when the Table is not in use.

25. Never reach under the Router Table for any

reason when the Router is running.

26. Avoid overloading the Router. If the speed drops abnormally,

decrease the pressure on the workpiece immediately.

27. Use the right tool for the job. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. There are certain

applications for which this tool was designed. It will do the job better and

more safely at the rate for which it was intended. Do not modify this tool,

and do not use this tool for a purpose for which it was not intended.

28. Always use sharp Router Bits (not included). If the Bit stops

abruptly, or the Bit becomes blocked, turn the Router Table’s

Power Switch to its “OFF” position immediately.

29. Before routing, run the Router for about ten seconds to ensure

all moving parts are running smoothly and there are no loose

parts, rattles, or sparking that would indicate damage.

30. WARNING! Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities, contain chemicals known (to the State of

California) to cause cancer, birth defects or other reproductive harm. Some

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 7

examples of these chemicals are: lead from lead-based paints, crystalline silica

from bricks and cement or other masonry products, arsenic and chromium from

chemically treated lumber. Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety equipment, such as

those dust masks that are specially designed to lter out microscopic particles.

(California Health & Safety Code § 25249.5, et seq.)

31. People with pacemakers should consult their physician(s) before

use. Electromagnetic elds in close proximity to heart pacemaker

could cause pacemaker interference or pacemaker failure.

32. WARNING! The warnings and cautions discussed in this manual cannot

cover all possible conditions and situations that may occur. It must be under-

stood by the operator that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

GROUNDING

Improperly connecting the grounding

wire can result in electric shock.

Check with a qualied electrician if you are in doubt as to

whether the outlet is properly grounded. Do not modify the

power cord plug provided with the tool. Never remove the

grounding prong from the plug. Do not use the tool if the

power cord or plug is damaged. If damaged, have it repaired

by a service facility before use. If the plug will not t the

outlet, have a proper outlet installed by a qualied electrician.

Grounded Tools: Tools with Three Prong Plugs

1. Tools marked with “Grounding Required” have a three wire cord and three

prong grounding plug. The plug must be connected to a properly grounded

outlet. If the tool should electrically malfunction or break down, grounding

provides a low resistance path to carry electricity away from the user,

reducing the risk of electric shock. (See 3-Prong Plug and Outlet.)

2. The grounding prong in the plug is connected through the green wire inside

the cord to the grounding system in the tool. The green wire in the cord must

be the only wire connected to the tool’s grounding system and must never be

attached to an electrically “live” terminal. (See 3-Prong Plug and Outlet.)

WARNING

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 8

3. The tool must be plugged into an appropriate outlet, properly installed and

grounded in accordance with all codes and ordinances. The plug and outlet

should look like those in the following illustration.

(See 3-Prong Plug and Outlet.)

THE

ROUTER TABLE

POWER CORD

USES A

3-PRONG PLUG

3-Prong Plug and Outlet Outlets for 2-Prong Plug

Double Insulated Tools: Tools with Two Prong Plugs

1. Tools marked “Double Insulated” do not require grounding. They have a special

double insulation system which satises OSHA requirements and complies

with the applicable standards of Underwriters Laboratories, Inc., the Canadian

Standard Association, and the National Electrical Code.

(See Outlets for 2-Prong Plug.)

2. Double insulated tools may be used in either of the 120 volt outlets

shown in the preceding illustration. (See Outlets for 2-Prong Plug.)

Symbology

Double Insulated V~ Volts Alternating Current

Canadian Standards Association AAmperes

Underwriters Laboratories, Inc. n0xxxx/min. No Load Revolutions

per Minute (RPM)

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts List on

pages 16 and 17 are included. If any parts are missing or broken, please call Harbor

Freight Tools at the number shown on the cover of this manual as soon as possible.

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 9

ASSEMBLY INSTRUCTIONS

Note: For additional information regarding the parts listed in the following

pages, refer to the Assembly Diagram on pages 16 and 17.

CAUTION! Always make sure the Power Switch (2B) of the

Router Table is in its “OFF” position and the unit is unplugged from

its electrical outlet prior to performing any assembly procedures.

To Attach the Legs to the Table:

1. Carefully turn the Router Table (5B) upside down.

2. Insert a Machine Screw (25B) through each of the 16 holes indicated with

an arrow in Figure A, below. Insert them so that the heads are near the top

of the table and the threads stick out to allow the Legs to be attached.

Figure A - Insert Machine Screws (25B)

upwards through the Table.

Table (5B)

Legs (1B)

3. Each Leg (1B) has four holes at its top. Place those holes

over the ends of the Screws as shown in Figure A.

4. Secure the Legs to the Screws using the Spring Lock

Washers (17B) and Nuts (18B). Tighten securely.

REV 11c

SKU 95380 For technical questions, please call 1-800-444-3353 PAGE 10

To Mount The Router Table On A Workbench:

1. CAUTION! Make sure the Router Table is securely attached

to a dry, at, level, sturdy workbench surface capable of supporting

the weight of the unit, accessories, and workpieces.

2. At the bottom of each of the four Legs (1B) of the Router Table are

two 1/4” diameter mounting holes. (See Assy. Diagram B.)

3. With assistance, place the Router Table in the desired location on the workbench.

Then use the mounting holes (eight total) in the Legs (1B) as a template to

mark where eight 1/4” diameter holes are to be drilled through the workbench.

4. Temporarily remove the Router Table from the workbench. Then, using

a 1/4” drill bit (not included), drill the pre-marked holes through the

workbench. Always check for hidden obstructions in the drilling path.

5. Place the Router Table back on the workbench and align the mounting

holes in its Legs (1B) with the pre-drilled holes in the workbench.

6. Secure the Router Table to the workbench, using eight 1/4” diameter Bolts of

appropriate length, eight Lock Washers, and eight Nuts (none included).

To Install The Miter Gauge:

Figure B

GUIDING GROOVE

(4B)

MITER GAUGE

(12B)

Make sure the Guiding Groove (4B) on the Worktable (5B) top is clean and free

of all debris. Then, insert the Miter Bar of the Miter Gauge (12B) in the groove.

Slide the Miter Gauge assembly forward and backward in the

groove to ensure proper installation. (See Figure B.)

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Chicago Electric

Chicago Electric

Chicago Electric 61737 Instrucciones de montaje

Chicago Electric

Chicago Electric 68221 Manual de usuario

Chicago Electric

Chicago Electric 37793 Manual de instalación

Chicago Electric

Chicago Electric PROFESSIONAL Series Instrucciones de montaje

Chicago Electric

Chicago Electric 68857 Instrucciones de montaje

Chicago Electric

Chicago Electric 67845 Manual de instalación

Chicago Electric

Chicago Electric 68012 Instrucciones de montaje

Chicago Electric

Chicago Electric 60428 Manual de usuario

Chicago Electric

Chicago Electric 95313 Manual de instalación

Chicago Electric

Chicago Electric Chicago Electric Power Tools 1600W Heavy Duty Heat... Instrucciones de montaje

Chicago Electric

Chicago Electric 57226 Instrucciones de montaje

Chicago Electric

Chicago Electric 90304 Manual de usuario

Chicago Electric

Chicago Electric 67537 Manual de usuario

Chicago Electric

Chicago Electric 67632 Manual de instalación

Chicago Electric

Chicago Electric 67707 Manual de instalación

Chicago Electric

Chicago Electric 61778 Instrucciones de montaje

Chicago Electric

Chicago Electric 96298 Manual de usuario

Chicago Electric

Chicago Electric 92880 Manual de instalación

Chicago Electric

Chicago Electric 68221 Instrucciones de montaje

Chicago Electric

Chicago Electric 93213 Manual de instalación

Chicago Electric

Chicago Electric 94782 Manual de lista de piezas

Chicago Electric

Chicago Electric 36W-110V HOT BLADE DECAL REMOVER Manual de instalación

Chicago Electric

Chicago Electric 66182 Manual de instalación

Chicago Electric

Chicago Electric BREAKER HAMMER 94882 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual