Check-line TSV-1000 Manual de usuario

Operating Instructions

Tachometer Stroboscope Calibrator / Verifier

TSV-1000

Thank you!

Dear Customers,

Thank you for purchasing the TSV-1000 Tachometer

and Stroboscope Calibrator / Verifier. This instruction

manual will help you to use the many features of your

new device. Before operation, please read this manu-

al completely, and keep it nearby for future reference.

SPECIFICATIONS

Accuracy ± 0.01% ± 1 digit

Presets 10 Programmable RPM setpoints

(TACHOMETER MODE)

Operating Modes TACHOMETER and STROBOSCOPE

Power Supply 100-240V AC to 5V DC

Warranty 1 Year

BEFORE USING THE TSV-1000

Plug in the AC (100-240VAC) to DC (5V) power

adapter.

Remove the pulsor / sensor from the rear panel stor-

age slot and plug it into the front panel USB connect-

or.

Power on the device using the switch on the rear

TSV-1000 Operation

By default, the device will start in TACHOMETER mode

and will pulse at RPM preset # 1 of 10.

To switch to STROBOSCOPE mode, press Swhile in

TACHOMETER mode.

To switch to TACHOMETER mode, press Twhile in

STROBOSCOPE mode.

• TACHOMETER MODE

To test a non-contact tachometer, hold the tachometer

so that its sensor is 0.5-2 inches / 12-50mm from the

TSV-1000 pulse sensor.

When the tachometer is in measuring mode its display

should be in-sync or close to in-sync with TSV-1000’s

display. The allowable tolerance will depend on the ta-

chometer’s specifications.

While in TACHOMETER mode, press SP+ or SP- to

toggle between presets (10).

Press ADJ+ or ADJ- to adjust the pulse rate.

To adjust the presets press DEFAULT, the display will

show Def X: Y where X is the preset number (0—9) and

Y is the preset value in RPM.

Press SP+ or SP- to toggle between presets (10)

Press ADJ+ or ADJ- to adjust a preset.

Press Default to save changes and exit the preset ad-

justment mode returning to normal operating mode.

To restore the default setpoints, press and hold Default

for 3 seconds.

In TACHOMETER mode, the default display is RPM. To

change the display to HZ, press and hold Tfor 3 sec-

onds. It will now display HZ. To return to RPM, press

and hold Tfor 3 seconds.

• STROBOSCOPE MODE

In STROBOSCOPE mode, hold the the stroboscope to

be tester 3-24 inches / 75-600mm away from the TSV-

1000 pulse sensor. The TSV-1000’s display should be in

-sync or close to stroboscope’s display. The allowable

tolerance will depend on the stroboscope’s specifica-

tions.

In STROBOSCOPE mode, the default display is FPM

(flashes per minute). To change the display to HZ, press

and hold Sfor 3 seconds. It will now display HZ. To re-

turn to FPM, press and hold Sfor 3 seconds.

Checkline

175 Vincent Ave

Lynbrook, NY 11563

Email: [email protected]

Website: www.checkline.com

Tel: 516-295-4300

Tabla de contenidos

Otros manuales de Equipo de prueba de Check-line

Check-line

Check-line DT-725 Manual de usuario

Check-line

Check-line QB-LED Manual de usuario

Check-line

Check-line TTC Series Manual de usuario

Check-line

Check-line DT-311D Manual de usuario

Check-line

Check-line NS-600 Manual de usuario

Check-line

Check-line FGV-XY Manual de usuario

Check-line

Check-line PK2 Manual de usuario

Check-line

Check-line DS-2000LED Manual de usuario

Check-line

Check-line MiniTest 7200 FH Manual

Check-line

Check-line TI-25S Manual de usuario

Check-line

Check-line TI-25P Manual de usuario

Check-line

Check-line CP-425-KIT Manual de usuario

Check-line

Check-line LS-9-12000 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario