Charnwood W660 Guía

TABLE SAW RIVING KNIFE ADJUSTMENT

MODEL: W660

It is possible that the factory setting of the riving knife restricts the maximum cutting

depth of the saw. If this is the case, the riving knife can be adjusted as follows:

1) Ensure that the machine is isolated from the power supply.

2) Raise the blade to its maximum height using the blade height adjustment hand

wheel at the front of the saw.

3) Remove the hose from the crown guard, remove the crown guard from the riving

knife, by loosening the black thumb screw.

4) In order to keep the Crown Guard parallel to the table, once the riving knife has

been adjusted, a slight modification will be needed to the plastic part.

Extend by 7mm

This allows the crown guard to rotate further on the pivot point and remain parallel to

the table after the adjustment. Use a sharp craft knife, carefully extend the slot at the

rear of the guard by approximately 7mm. You might find this easier if the two sides of

the guard are first split.

5) Slide the carriage fully forward to expose the riving knife attachment nut.

6) The nut holding the riving knife can now be loosened using a 16mm spanner.

7) Raise the riving knife and crown guard assembly, so that the crown guard is

situated just above the top of the saw blade. If necessary adjust the riving knife so

that there is an even gap between the leading edge of the riving knife and the radius

of the saw blade. Adjust the crown guard so that it is parallel to the table.

8) Re-tighten the bolt.

The saw can now be used to the full cutting capacity.

Otros manuales para W660

1

Tabla de contenidos

Otros manuales de Sierra de Charnwood

Charnwood

Charnwood W619 Manual de usuario

Charnwood

Charnwood W715 Manual de usuario

Charnwood

Charnwood W650 Manual de usuario

Charnwood

Charnwood W618 Manual de usuario

Charnwood

Charnwood SS16F Manual de usuario

Charnwood

Charnwood W625 Manual de usuario

Charnwood

Charnwood W619PSF Manual de usuario

Charnwood

Charnwood W721 Manual de usuario

Charnwood

Charnwood W616 Manual de usuario

Charnwood

Charnwood W616 Manual de usuario

Charnwood

Charnwood W650 Manual de usuario

Charnwood

Charnwood W650 Manual de usuario

Charnwood

Charnwood W715 Manual de usuario

Charnwood

Charnwood 305DB Manual de usuario

Charnwood

Charnwood W650 Guía

Charnwood

Charnwood W711 Manual de usuario

Charnwood

Charnwood W730 Manual de usuario

Charnwood

Charnwood BS410 Manual de usuario

Charnwood

Charnwood W629 Manual de usuario

Charnwood

Charnwood W730 Manual de usuario

Charnwood

Charnwood W629PSF Manual de usuario

Charnwood

Charnwood W721 Manual de usuario

Charnwood

Charnwood TS10F Manual de usuario

Charnwood

Charnwood W619 Guía

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario