Channel Master CM-7000 Manual de usuario

USER MANUAL

by PCT

HIGH-

DEFINITION TELEVISION

COMPATIBLE

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

PLEASE READ THIS OWNER’S GUIDE

Please take the time to follow this owner’s guide carefully. It will help you set up and operate

your system properly, and enjoy all of its advanced features. Save your owner’s guide for future

reference.

WARNING: To reduce the risk of ﬁre or electric shock, do not expose the system to rain or

moisture.

WARNING: This apparatus shall not be exposed to dripping or splashing, and objects ﬁlled with

liquids, such as vases, shall not be placed on the apparatus. As with any electronic products, use care

not to spill liquids in any part of the system. Liquids can cause a failure and/or a ﬁre hazard.

The CAUTION marks shown here are located on the back of your CM-7000 D2A Digital to Analog

Converter.

The lightning ﬂash with arrowhead symbol, within an equilateral triangle, alerts the user to the

presence of uninsulated dangerous voltage within the system enclosure that may be of sufﬁcient

magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle alerts the user to the presence of important

operating and maintenance instructions in this owner’s guide.

CAUTION To prevent electric shock, match wide blade of plug to wide slot, insert

fully.

CAUTION No open ﬂame sources, such as lighted candles, should be placed on the

apparatus.

BATTERIES

Please dispose of used batteries properly, following any local regulations. Do not incinerate.

WARRANTY

This Channel Master product is warranted to be free from defects in material and workmanship under normal use

and service for a period of 90 days after purchase by the original purchaser. If the product does not conform to this

warranty, Channel Master shall replace it if it is returned to the dealer within the 90-day warranty period, and if

examination reveals to Channel Master’s satisfaction, that the product is defective. Claimants under this warranty should

present their claim along with the defective product, proof-of-purchase and the Warranty Certiﬁcate originally supplied

with it, to their dealer immediately upon failure. Noncompliance with any part of this claim procedure may invalidate

this warranty in whole or in part. Contact Channel Master for details.

distributed or otherwise used without written permission. The distinctive design of the D2A Digital Converter is a trademark of

Channel Master by PCT, a division of PCT International, Inc.

The Channel Master logo is used under licensed agreement.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

QUICK SET-UP GUIDE

Connect the CM-7000 using one of the methods that best matches the

connections on your TV (see pages 4 to 7).

Select either Channel 3 or 4 with the CH3/CH4 switch on the back of1.

the CM-7000.

a. Set your TV to the corresponding Channel 3 or 4 if connecting via RF

COAXIAL CABLE (page 4).

b. Set your TV to VIDEO or AUXILIARY if connecting via RCA or RCA &

S-VIDEO CABLE (page 5).

Press MENU on the CM-7000 remote. The main menu should appear on2.

the TV screen.

Press the3. button and “TERRESTRIAL” should appear on the menu.

Press OK button 3 times to start the AUTO CHANNEL SCAN.4.

When the AUTO SCAN is complete, press EXIT. Use the5.  buttons to

begin watching digital TV.

INFORMATION REGARDING THE DIGITAL TV TRANSITION

Aftr February 17, 2009, a television receiver

with only an analog broadcast tuner will

require a converter box to receive full power,

over the air broadcasts with an antenna due

to the USA’s nationwide transiton to digital

broadcasting. Analog only TVs should continue

to work as before to receive low power, Class

A or translator TV stations, cable/satellite

services, gaming consoles, VCRs, DVD players,

and similar products.

Information about the DTV transition is

available at:

www.DTV.gov or 1.888.CALL.FCC

Information about subsidized coupons for

digital to analog converter boxes (like the

CM-7000) is available at:

www.dtv2009.gov or 1.888.DTV.2009

The CM-7000 digital to analog convert box is

capable of receiving digital broadcasts via a

TV antenna and displays them on an analog

TV set. This converter box does not include

analog pass through, so the use of an A/B

switch or splitter is required to receive both

digital and analag signals from one antenna

(see pages 6 and 7).

See pages 4 to 7 to view image details.

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

INTRODUCTION

The Channel Master by PCT CM-7000 is a high quality

HD/SD (high deﬁnition/standard deﬁnition) digital ATSC

to analog NTSC television converter box. Using the CM-

7000 for direct terrestrial FTA HD reception allows users

to view HD programs on SD TV sets.

The combination of a CM-7000 Digital Analog Converter

with a Channel Master digital antenna is a perfect

solution for terrestrial reception in a very wide range of

reception conditions and landscape relief.

For energy saving, which is in compliance with NTIA

recommendations, the Auto-Sleep Function activates

Standby mode four (4) hours after last user entry from

the remote control, but not before the end of a currently

viewed event.

FEATURES

Converts all digital video formats,•

including HD (High Deﬁnition) into

SD (standard deﬁnition)

analog format

Easy installation and operation•

Automatic and manual programming•

Electronic Program Guide (EPG) support•

On Screen Display (OSD)•

Closed Caption (CC)•

Full function remote control•

Low power consumption•

Auto-Sleep function•

SAFETY!

POWER Power this box only from a power source within the speciﬁed voltage range

To prevent electrical shock, be sure the electrical plug used on the box’s power cord matches

the electrical outlet in use.

Do not open the top cover when the box is plugged into an electrical outlet.

CONNECTION Connect all peripheral devices before plugging the power cord into the electrical outlet.

Unplug power cord from the electrical outlet before disconnecting any peripheral devices.

GROUNDING Terrestrial antenna must be grounded to provide protection from lightning and build-up of

static electricity.

LIGHTNING For protection from lightning or when the box is left unattended for a long period, disconnect

it from the power source.

VENTILATION

The slots on the top of the CM-7000 must be left uncovered to allow proper airﬂow to the unit.

Do not cover the top with fabric, paper, or other materials.

Do not stack electronic equipment on top of the CM-7000.

OVERHEATING Do not install this box on soft furnishings or carpet.

Do not expose this box to direct sunlight or place it near a heater.

Do not install this box in small or non-ventilated openings between furniture.

LIQUIDS This box should not be exposed to liquids nor should objects ﬁlled with liquid be placed on

top of the box.

ENVIRONMENT CM-7000 is for indoor use only under speciﬁed conditions.

CLEANING Disconnect the box from the electrical outlet before cleaning.

Use a light damp cloth (no solvents) to clean the box.

On/Off Channel

Down Channel

Up IR Remote Window

Not a display window

Power LED

Light*

* Green = ON, Orange = Stand-By, Red = Booting Up

Note: Initial boot up process occurs when the unit is

ﬁrst plugged in. Boot up may take up to 45 seconds

to complete and is followed by a green LED.

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

TUNER

Frequency Range 54 to 864 MHz

Input Impedance 75 Ohm

Input Connector F-Type, Female

Channel Bandwith 6 MHz

Input Dynamic Range -83 to -5 dBM / SNR - 15 dB

DEMODULATOR

Type 8VSB / ATSC A/53 compliant

Performance ATSC A/74 compliant

Input Video Formats 1080i, 720p, 480i, 480;

VIDEO

Output Format 480i

Aspect Ratio 4:3 / 16:9 with letter box pan and scan

CONNECTORS

Video

Composite Video RCA

Component Video S-Video

Audio

Left / Right RCA, Stereo

RF MODULATOR

Output RF Connector F-Type, Female

Channel 3 / 4, Selectable, Mono Audio

POWER

Supply 120 VAC / 60 Hz

Consumption “ON” 8 W

Consumption “STANDBY” 2 W

Auto-Sleep Mode 4 hours after last remote control entry

GENERAL

Dimensions (W x L x H) 22 x 16 x 4 cm / 8.7 x 6.3 x 1.6 in

Weight 0.9 kg / 2.0 lbs

ENVIRONMENT

Operating Temperature 0 to 60° C / 32 to 140° F

Relative Humidity 10 to 90% noncondensing

SPECIFICATIONS

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

CONNECTING - ANTENNA

CONNECTING CM-7000 TO A TV USING RF COAXIAL CABLE

CONNECTING CM-7000 TO A VCR USING RF COAXIAL CABLE

GOOD RF Coaxial Cable

Back of CM-7000

ANT INCVBS L R

Back of TV

Terrestrial Antenna

(outdoor or indoor)

Back of CM-7000

GOOD

Terrestrial Antenna

(outdoor or indoor)

RF Coaxial Cable

ANT INCVBS L R

Back of TV

OUT

Back of VCR

FIGURE 1

FIGURE 2

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

Back of CM-7000

CONNECTING CM-7000 TO A TV USING RCA CABLE

CONNECTING - ANTENNA

CONNECTING CM-7000 TO A TV USING RCA & S-VIDEO CABLE

BETTER RCA Audio/Video Cable

Back of CM-7000

ANT INCVBS L R

Back of TV

Terrestrial Antenna

(outdoor or indoor)

BEST

ANT INCVBS L R

Back of TV

Terrestrial Antenna

(outdoor or indoor)

S-Video Cable

Audio RCA Cable

FIGURE 3

FIGURE 4

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

CONNECTING - NO ANALOG PASS THROUGH

VIA AUDIO/VIDEO

VIA SPLITTER A/B SWITCH HOOKUP

Terrestrial

Antenna

(outdoor)

CM-7000 is connected to TV set via audio / video.1.

Antenna is connected to TV tuner.2.

Tune to analog channels with TV and select AV input for CM-7000.3.

ANT INCVBS L R

Splitter

Back of CM-7000

RCA Audio/Video Cable

RF Coaxial Cable

Antenna In Back of TV

A/B SWITCH

IN IN

Terrestrial

Antenna

(outdoor)

Antenna is connected to TV tuner and CM-7000.1.

Converter box modulator is combined with antenna using an A/B switch.2.

Select A to watch analog signals and B to watch digital signals3.

via CM-7000.

ANT INCVBS L R

Splitter

Back of CM-7000

RF Coaxial Cable

Antenna In Back of TV

RF Coaxial Cable

RF Out

Ch 3 or 4

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

CONNECTING - AUDIO/VIDEO

VIA SPLITTER COMBINER USING FILTERING DEVICE HOOKUP

Ch 3/4 Combiner

IN 3/4

Terrestrial

Antenna

(outdoor)

Antenna is connected to TV tuner and CM-7000.1.

Converter box modulator is combined with antenna using a Ch 3/4 combiner2.

that ﬁlters 3 and 4 from the antenna side to reduce interference.

Select ??? to watch analog signals and ??? to watch digital signals3.

via CM-7000.

ANT INCVBS L R

Splitter

Back of CM-7000

RF Coaxial Cable

Antenna In Back of TV

RF Coaxial Cable

RF Out

Ch 3 or 4

CM-7000 D2A DIGITAL TO ANALOG CONVERTER

MENU TREE

DETAIL OF THE SET-UP FUNCTIONS.

CHANNEL EDIT SET UPCHANNEL SCAN PARENTAL

CONTROL

CLOSED

CAPTIONED

ALL CLOCKTERRESTRIAL PASSWORDSERVICE

FAVORITES LANGUAGE MOVIE

RATING

PREFERENCES

DELETED UNIVERSAL RC TV

RATING

LOCKED DEFAULTS ADDITIONAL

RATING

VERSION LOCK

AUTO

POWER DOWN

SET UP MENU FUNCTIONS

CLOCK

Sets date and time. Has auto or manual setting. Auto

setting is recommended. To set:

Press Menu1.

Use2.  menu buttons to select SET UP screen

Press3. OK to select CLOCK

Press4. OK to select DATE and TIME

Use5.  buttons to select AUTO DATE and

TIME

Press6. right button to select TIME ZONE

Use7.  buttons to change TIME ZONE

Press8. button to select DST

Use9.  buttons to change DST

Press10. Exit to store

LANGUAGE

Used to select between three (3) different onscreen

display languages. To change:

Press1. Menu

Use2.  buttons to select SET UP screen

Press3. OK to select LANGUAGE

Use4.  buttons to change LANGUAGE choice

Press5. OK to select

Press6. Exit to store

UNIVERSAL RC

Universal remote control function. Used to turn on or off

the universal remote control function. Factory setting is

set to ON. Use the Pioneer Cable Box code if using

a universal remote. If using a Channel Master remote

controlled rotator, you may turn the universal remote

control feature OFF to avoid conﬂicts between the rotator

remote control and the converter box. To turn OFF:

Press1. Menu

Use2.  buttons to select SETUP screen

Press3. OK to select Universal RC

Press4. OK to select ON

Press5.  buttons to change to OFF

Press6. OK

Press7. Exit to store

DEFAULTS

Restores setting to factory default settings. The default

password is 0000. To reset password:

Press1. Menu

Use2.  buttons to select PARENTAL CONTROL

screen

Press3. OK to select PASSWORD

Press4. OK then button to select NEW

PASSWORD

Enter5. 0000 in new password ﬁeld

Press6. button to select RESET PASSWORD

Press7. OK

Password is now set to 00008.

AUTO POWER DOWN

Turns unit off after four (4) hours without user input.

This is a required, energy saving feature. Factory default

is ON and the unit will shut OFF after four (4) hours

without user input (ex: pressing CH+, CH-, or Info).

To turn off this feature:

Press1. Menu

Use2.  buttons to select SET UP screen

Press3. OK and a warning screen appears

Press4. button to select YES

Press5. OK

Press6. OK to uncheck the AUTO POWER DOWN box

Press7. Exit to store

The length of time to power down, and the option

to turn off the warning screen are also accessed from

this menu.

Otros manuales para CM-7000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Channel Master

Channel Master

Channel Master CM-7000 Manual de usuario

Channel Master

Channel Master CM-7000 Manual de usuario

Channel Master

Channel Master CM-7000 Manual de usuario

Channel Master

Channel Master CM-7004 Manual de usuario

Channel Master

Channel Master CM-7003 Manual de usuario

Channel Master

Channel Master D2A CM-7000 Manual de usuario

Channel Master

Channel Master CM-7000 Instrucciones de funcionamiento

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario