Chamberlain TriCode Systems Manual de usuario

TriCode LiftMaster Four Button Garage Door Opener Remote Control

Transmitter Coding Instructions

TC4 Four Channel Transmitter Coding Instructions

This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations.

Operation is subject to the following two conditions: (1) This device may not cause harmful

interference and (2) this device must accept any interference received, including

interference that my cause undesired operation. F.C.C. rules prohibit adjustments to or

modification of receiver and/or remote control transmitter circuitry except for changing the

code setting and replacing remote control transmitter battery. THERE ARE NO OTHER

SERVICEABLE PARTS.

CAUTION

ACTIVATE THE TRANSMITTER ONLY WHEN THE DOOR/GATE IS IN FULL VIEW,

FREE OF OBSTRUCTION AND PROPERLY ADJUSTED. NO ONE SHOULD ENTER OR

LEAVE THE DOOR/GATE WHILE IN MOTION. DO NOT ALLOW CHILDREN TO

OPERATE THE REMOTE(S) OR THE DOOR/GATE CONTROL BUTTONS. DO NOT

ALLOW CHILDREN TO PLAY NEAR THE DOOR/GATE.

The TriCode™ digital TC4 transmitter is a four-channel wireless radio control designed for

use with automatic garage/gate operators and access control systems. All TriCode™

products can be used with Linear/Delta 3™, Stanley™ and Multi-Code™ receivers. Two

configuration switches allow the four buttons to be configured to interface with two different

receiver types in the same transmitter. The TriCode™ radio format provides a potential of

2048 different digital codes. Two 10-posistion DIP switches, each capable of 1024 different

digital codes provide these codes. For Delta-3™ products, 512 (256x2) different digitals

codes are available.

SWITCH SETTINGS

CAUTION: To avoid possibility of duplicating codes in adjacent systems, all

transmitters should be recoded prior to operation. Unless using the maximum

number of codes four codes should not be used:

All DIP Switches ON

All DIP Switches Off

DIP Switches alternating ON/OFF

DIP Switches alternating OFF/ON

STEP 1: LOCATE SWITCHES AND CONNECT BATTERY

Locate the DIP switches, configuration switches and battery by sliding down access cover on

front of the transmitter case. DIP switches are numbered 1 through 10. The configuration

switches are located to the right of the DIP switches. The battery is located below the

switches. Connect the battery connector to the 9V battery before programming transmitter

STEP 2: SET TRANSMITTER CONFIGURATION SWITCH(S)

The TriCode™ Transmitter is factory set to Linear/Delta-3™ position. Using a pointed object

set transmitter configuration switches to desired setting..

STEP 3: SET TRANSMITTER DIP SWITCH(S)

The TriCode™ Transmitter DIP switch(s) are factory set, CH1 OFF (1-10) and CH2 ON (1-

10).

Using a pointed object set transmitter DIP switches to desired setting. For Linear/Delta-3™

compatibility, set codes on switches 1 through 8. Switches 9 and 10 are not used for

Linear/Delta-3™ products.

Note: Switches in receiver must match the switches in all transmitters used to

operate the receiver. Some older radios use toggle switches and it may be difficult

to determine 'ON' & 'OFF'. If so, try reverse settings on the TriCode™.

STEP 4: RECODE RECEIVER CODES

Once the transmitter codes have been set, verify the receiver codes are set to the following

settings:

Linear/Delta-3™ Receiver Type Detail

When the TC4 is set to the Linear/Delta-3™ transmitter type, set the receiver DIP switches

as follows.

Receiver 1 - Set switch 1-8 to match switch 1, activates from Button 1.

Receiver 2 - Set switches 1 and 2 OFF, match switches 3-8 on switch 2, activates from

Button 2.

Receiver 3 - Set switch 1 ON, switch 2 OFF, match switches 3-8 on switch 2, activates from

Button 3.

Receiver 4 - Set switch 1 Off, switch 2 ON, match switches 3-8 on switch 2, activates from

Button 4.

Multi-Code™ Receiver Type Detail

When the TC4 is set to the Multi-Code™ transmitter type, set the receiver DIP switches as

follows.

Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.

Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.

Receiver 3 - Set switch 10 OFF. match switches 1-9 on switch 2, activates from Button 3.

Receiver 4 - Set switch 10 ON, match switches 1-9 on switch 2, activates from Button 4.

Stanley™ Radio Receiver Type Detail

When the TC4 is set to the Stanley™ radio transmitter type, set the DIP switches as follows.

Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.

Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.

Receiver 3 - Set switch 10 OFF, match switches 1-9 on switch 2, activates from Button 3.

Receiver 4 - Set the switch 10 ON, match switches 1-9 on code switch 2, activates from

Button 4.

NOTE: The DIP switches in the receiver must match the DIP switches in all transmitters

used to operate the receiver.

STEP 5: TEST THE EQUIPMENT

If not already installed, connect the receivers to the operators as described in their

installation instructions. Be sure the door/gate is clear of people and obstructions.

Activated each transmitter button and verify that each receiver triggers its operator.

Battery Replacement: The 9 volt battery should last 12 to 18 months of normal use. The

red LED on the face of the transmitter will light dimly or not at all when the battery needs

replacing. The battery is located under the access cover.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mando a distancia de Chamberlain

Chamberlain

Chamberlain LiftMaster Security+ 973LM Manual de usuario

Chamberlain

Chamberlain 972LM Security? Manual de usuario

Chamberlain

Chamberlain Security+ 963D Manual de usuario

Chamberlain

Chamberlain 972LM Manual de usuario

Chamberlain

Chamberlain Security+ 950-315CB Manual de usuario

Chamberlain

Chamberlain KLIK5C-BK2 Manual de usuario

Chamberlain

Chamberlain 811LM Manual de usuario

Chamberlain

Chamberlain Liftmaster Security+ 974LM Manual de usuario

Chamberlain

Chamberlain Clicker KLIK1U Manual de usuario

Chamberlain

Chamberlain LiftMaster Professional 84LM Manual de usuario

Chamberlain

Chamberlain 811LM Manual de usuario

Chamberlain

Chamberlain LiftMaster Security+ 973TB Manual de usuario

Chamberlain

Chamberlain LiftMaster 535LM Security+ Manual de usuario

Chamberlain

Chamberlain Prosfessional Series Manual de usuario

Chamberlain

Chamberlain 84330AML Manual de usuario

Chamberlain

Chamberlain MC100C Manual de usuario

Chamberlain

Chamberlain PASSPORT CPT4 Manual de usuario

Chamberlain

Chamberlain Security+ 963CD Manual de usuario

Chamberlain

Chamberlain LiftMaster 333LM Manual de usuario

Chamberlain

Chamberlain E940C Manual de usuario

Chamberlain

Chamberlain LIFT-MASTER 83LM Manual de usuario

Chamberlain

Chamberlain 956D Manual de usuario

Chamberlain

Chamberlain LiftMaster Security+ 327LM Manual de usuario

Chamberlain

Chamberlain LiftMaster 373W 315 MHz Security+ Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación