Chamberlain HL410-11 Manual

Doc 01-20238

Rev B

Installation and

Maintenance Manual

Commercial Hydraulic Vehicular

Swing Gate Operator

Model HL410-11

2Contents

Doc 01-20238

Rev B

Contents

Parts & Components ____________________________________________ 3

Specifications & Capacities _______________________________________ 4

Safety Information______________________________________________ 6

Installer _______________________________________________________________ 6

End User _______________________________________________________________ 7

General Wiring Information ______________________________________ 8

Wiring Information _______________________________________________________ 8

Installation___________________________________________________ 10

Step 1: Gate Stops______________________________________________________ 10

Step 2: Gate Brackets ___________________________________________________ 10

Step 3: Optional Mounting _______________________________________________ 11

Step 4: Mounting ______________________________________________________ 12

Control Panel Layout ____________________________________________________ 13

Step 5: Primary Voltage Wiring ___________________________________________ 14

Step 6: Control Wiring __________________________________________________ 15

Step 7: Hydraulic Adjustments____________________________________________ 16

Step 8: Electrical Adjustments ____________________________________________ 17

Step 9: Rod Cover______________________________________________________ 18

System Check-Out _____________________________________________ 20

Limited One-Year Warranty_______________________________________________ 20

Parts List ____________________________________________________ 21

Required Maintenance Services __________________________________ 22

Parts & Components 3

Doc 01-20238

Rev B

Parts & Components

Inspect the operator for possible shipping damage or shortage of parts. Check all

accessories as listed below. These do not include any accessories that were ordered

separately.

DESCRIPTION QUANTITY

Model HL410-11 1

Front Mounting Bracket 1

Rear Mounting Bracket 1

Rod Cover 1

Rear Mounting Pin 1

C-Clip 1

Front Mounting Clip 1

Disconnect Key 1

Gate Caution Plate !+2

Troubleshooting Guide 1

Controller (sold separately) 1

Table 1

!Gate Caution Plates are to be installed on the gate in a position where they can be

easily seen.

!! U.L. listing is valid only if a LiftMaster drive unit is used with a LiftMaster controller.

+ Packed with controller

4Specifications & Capacities

Doc 01-20238

Rev B

Specifications & Capacities

The Model HL410-11 is a light duty commercial gate operator designed to operate a

typical swing gate. Because operating requirements and gate construction vary by

installation, the capacities shown should be used as a guide to determine the expected

performance of the unit.

01-20238F1

Figure 1

MAXIMUM LENGTH VS. MAXIMUM WEIGHT

0 - 8ft 500 lbs

8 - 10ft 300 lbs

10 - 12ft 250 lbs

Table 2

Contact a LiftMaster dealer if your application exceeds any of the recommended limits

to determine the proper unit needed.

!Double Check Operator Capacities!

!Do not use this operator on “walk or pedestrian” gates.

!Do Not Misapply Product. Warranty will be void!

Specifications & Capacities 5

Doc 01-20238

Rev B

NOTE

The hydraulic locking is not intended to be a replacement for security type

locks. External lock systems should be used if:

High security is required for the installation.

The length of the gate exceeds 12 feet.

The gate has a large surface area.

The installation area could have a strong or gusty winds.

SPECIFICATIONS

Cycles per hour (Full open & close) 10 maximum

Time to open (Avg.) 20 seconds

Hydraulic (gate) Locking !Close Direction

Primary Voltage 120 VAC ~1∅~ 60hz

Secondary Voltage 24 VAC

Power Consumption 335 W (full load)

Current 3-1/2 A (full load)

Motor R.P.M 1700

Motor Overload 135 C

Fluid Dexron ATF

Table 3

!It is highly recommended that you reconsider using this type of gate operator on

any solid faced gate, without an external lock system on both the open and

closed position. Strong winds will greatly affect the efficiency of this operator on

these types of gates.

IMPORTANT NOTE

The gate must be level and operate smoothly and freely. If it does not, damage

to the operator may result and the life expectancy will be greatly reduced.

6Safety Information

Doc 01-20238

Rev B

Safety Information

Automatic gate operators provide convenience and security to their users. However,

because these machines can produce high levels of force, it is important that all

installers and users be aware oft he potential hazards associated with improperly

installed or adjusted units.

The information on this page contains various safety precautions and warnings, some

highlighted with this symbol (see left margin). This symbol will identify conditions that

can result in serious injury or death. Take time to read and follow these precautions

and the other information provided.

NOTE

This operator is intended to be a part of a total gate operating system. It is the

responsibility of the purchaser and installer to ensure that the total system is safe

for its intended use.

Installer

BEFORE INSTALLATION

1 Check to see that this is the proper operator for this application. (See page

4).

2 Ensure that the gate has been properly installed and works freely in both

directions. Repair or service any worn or damaged gate hardware.

3 Install the gate operator on the inside of the property and/or fence line. Do

not install an operator on the public side of the gate.

4 If the gate is near a residential area, or pedestrian traffic is expected near the

gate, additional safety equipment such as electric gate edges or photocell

detectors must be installed to prevent entrapment. Severe injury or death

can result from entrapment with the gate.

5 Certain types of gates can create greater hazards to pedestrians. Any gate

that has exposed, reachable pinch points or is constructed to allow arms and

legs to pass through it is a potential hazard. These hazards should be

guarded against.

6 Review the operation of the unit and become familiar with the manual

disconnect system and safety features of the unit.

7 Outdoor or easily accessed controls should be of the security type to prohibit

unauthorized use of the gate.

Safety Information 7

Doc 01-20238

Rev B

DURING INSTALLATION

1 Be aware of all moving parts and avoid close proximity to any pinch

points.

2 Disconnect power at the service panel before making any high voltage

power connections.

3 Place controls far enough from the gate so that a user can see but cannot

touch the gate while operating the controls.

4 Place warning signs provided on the gate or in a high visibility area to

alert of automatic gate operation.

AFTER INSTALLATION

1 Make sure the user understands the basic function and safety features of

the system.

2 Leave this manual and the troubleshooting guide with the end user.

End User

1 Periodically check all the safety systems. If these functions are observed

to operate improperly, discontinue use and contact a professional for

service immediately.

2 Follow recommended maintenance schedule.

3 Do not allow children to play on or near the gate operating system.

4 Never operate the gate until you have it in full sight.

5 See p. 16 for pressure valves and manual disconnect information.

8General Wiring Information

Doc 01-20238

Rev B

General Wiring Information

CONTROLLER

DRIVE UNIT DRIVE UNIT,

SLAVE OPTION

JUNCTION BOX,

SLAVE OPTION

CONDUIT FOR SLAVE (4 WIRES)

Suggest 10-gauge stranded wire

CONDUIT, POWER

(3 WIRES)

CONDUIT, CONTROL

(as required)

01-20238F2

Figure 2

NOTE

Other wire runs may be required, depending on your application.

Wiring Information

The distance shown on charts is the total length of wire, measured in feet from

the control panel to the power source. Do not exceed maximum distance.

Supply voltage must be within 10% of the unit’s rating under lead conditions.

(Measure voltage at the unit).

Connect power in accordance with local codes.

Wire tables are based on stranded copper wire. Wire insulation must be

suitable to application.

All units, single and master/slave, must be properly grounded with a supply

grounding conductor.

Do not run control wires in the same conduit with power wires.

Do not use solid copper wires for controls.

Do not use parallel conductor cable.

If PVC type conduit is used in a single trench, allow a minimum of six (6)

inches between lines.

General Wiring Information 9

Doc 01-20238

Rev B

POWER WIRING

Maximum Distance

Single Unit Dual Unit Wire Gauge

200 ft 100 ft 10

310 ft 155 ft 8

500 ft 250 ft 6

CONTROL WIRING

200 ft 18

400 ft 16

Table 4

10 Installation

Doc 01-20238

Rev B

Installation

Step 1: Gate Stops

The gate must have a permanent gate stop at the full closed position. It is also highly

recommended that there be a gate stop at the determined full open position. These are

to prevent the piston from bottoming in the cylinder and to prolong the unit’s life.

Step 2: Gate Brackets

1 Locate the positions of the front and rear mounting brackets. It is

recommended that these brackets be positioned at the midpoint between the

gate hinges.

It is very important that they be in-line with each other! The operator

must be level.

2 The two brackets should be welded to the

gate and the post as shown. They can be

welded directly or modified to suit your

particular application.

Do not weld brackets with

operator attached. Avoid getting weld splatter on the piston rod.

Keep piston rod clean and smooth. Avoid nicks.

01-20238F3

Hinge Point Front Mounting Bracket

(shortest)

3-1/2” to 4” A

3” to 3-1/4”

3-1/2”

Rear Mounting Bracket

(longest)

Open

Both Brackets in Line

Gate shown in the Left-Hand Position

Figure 3

FOR MODEL HL410-11

Dimension A Gate Opening

26 inches 90° only

27 inches 90° or 100°

Tabla de contenidos

Otros manuales de Abridor de puerta de Chamberlain

Chamberlain

Chamberlain LiftMaster Professional SW470 Manual de usuario

Chamberlain

Chamberlain ELITE Series Guía de inicio rápido

Chamberlain

Chamberlain HC500ML-24 Manual de usuario

Chamberlain

Chamberlain Liftmaster SL3000101UL Manual de usuario

Chamberlain

Chamberlain LA400 Manual de usuario

Chamberlain

Chamberlain LiftMaster Professional SL585GL Manual de usuario

Chamberlain

Chamberlain SL600 Manual de usuario

Chamberlain

Chamberlain LMWEKITU Manual de usuario

Chamberlain

Chamberlain HC300 Manual de usuario

Chamberlain

Chamberlain GJ Manual de usuario

Chamberlain

Chamberlain ESTATE SERIES SW 2000-X3 Manual de usuario

Chamberlain

Chamberlain 975 Manual de usuario

Chamberlain

Chamberlain AA250EVK Manual de usuario

Chamberlain

Chamberlain GT Manual de usuario

Chamberlain

Chamberlain B4603TC Manual de usuario

Chamberlain

Chamberlain SL595101UL Manual de usuario

Chamberlain

Chamberlain LA400 Manual de usuario

Chamberlain

Chamberlain 1000 Series Manual de usuario

Chamberlain

Chamberlain CSO Manual de usuario

Chamberlain

Chamberlain Mega Arm Tower Manual de usuario

Chamberlain

Chamberlain MotorLift 808EML1 Manual de usuario

Chamberlain

Chamberlain HDLGARM Manual de usuario

Chamberlain

Chamberlain Elite SL3000 Manual de usuario

Chamberlain

Chamberlain MADCBB Manual de usuario

Manuales populares de Abridor de puerta de otras marcas

Elite

Elite CSW200UL Manual de usuario

CAME

CAME FROG-PM4 Manual de usuario

SOMFY

SOMFY FX230 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Manual de usuario

Turnstiles

Turnstiles FSW 900 Manual de usuario

Erreka

Erreka BUL BL33 Instrucciones de funcionamiento

Erreka

Erreka VULCAN S Manual de usuario

Beninca

Beninca R1-2 WBV Manual de usuario

Erreka

Erreka VULCAN D Manual de usuario

Motorline professional

Motorline professional FORT Manual de instrucciones

Beninca

Beninca BOB5024 Manual de usuario

AGA

AGA GATEMASTER 900 HD Manual de usuario

SOMFY

SOMFY Dexxo RTS Pro Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Westfalia

Westfalia 85 27 06 Manual de usuario

CAME

CAME F500 Manual de usuario

Extel

Extel VERA Manual de usuario

Comunello Automation

Comunello Automation ABACUS 220 Manual de usuario