Challenge SCM Manual de referencia técnica
The
Challenge Machinery Company provides owner's
manuals on its products solely as a courtesy to its customers.
See the information below before using this manual.
These manuals are for reference only. These manuals include products which are non-
current, unsupported or no longer produced by The Challenge Machinery Company, and are
provided solely as an accomodation to our customers. By providing these manuals, The
Challenge Machinery Company makes no representation or warranty as to the products,
their current condition, or their suitability or fitness for use in any particular application, which
are the sole and independent responsibility of the product owner and user.
Older products may not comply with current safety procedures, guidelines or regulations,
and it is the product owner's and user's responsibility to evaluate the suitability and fitness of
the products in their current use and application. The Challenge Machinery Company makes
no representation, warranty or recommendation regarding any modifications which may be
required on non-current or unsupported products. The Challenge Machinery Company
assumes no liability for any modification or alteration to any Challenge product, and any such
modification or alteration to any Challenge product is not authorized by The Challenge
Machinery Company. The availability of these manuals is solely for the purpose of providing
reference information for the products.
This
manual
may not be
complete
in all aspects of
product
maintenance
and
repair.
All
products should be used only by qualified and properly trained personnel, following proper
safety procedures. All products should be regularly inspected and maintained, and their condition,
application and use should be periodically evaluated by qualified personnel. Only qualified and
properly trained technicians should perform maintenance,
repair
and replacement
procedures. Attempting
t
hese procedures without proper training
may
cause
machine
damage or
operator
injury!
Products
may be
unsupported by The Challenge Machinery Company
due to age or the
unavailability
of parts from their
original manufacturer.
No parts or
product support
will be
available
to repair or
maintain unsupported
products.
Older
products
may not be UL
listed (if
the product does not have a UL label it is not a listed product), and may not comply with
applicable installation or other regulations or requirements if
relocated
to a new
facility.
Many
municipalities require
a
product
to be UL
listed
before
an
electrician
will
connect
power
to them. Often the cost of updating an older product to comply with current safety regulations is
greater than the value of the product.
F.329-B
SCM/MSCM
SINGLE CORNERING MACHINE
Sold and Serviced by
The Challenge Machinery Company
6125 Norton Center Drive
Norton Shores, MI 49441-6081 USA
www.ChallengeMachinery.com
Serial Numbers 2167A & U
p
INSTRUCTION AND
P
A
RTS
M
A
NUAL
1.0 Introduction
2
1.0 Introduction
Keep this manual in a safe, convenient place for quick reference by operators and service personnel.
SAFETY ALERT! This symbol means CAUTION: Personal safety
instructions! Pay special attention to the instructions in bold type.
Personal injury may result if the precautions are not read and followed.
READ THIS MANUAL BEFORE OPERATING! If you follow precautions and instructions, you should
have years of trouble-free operation. Contact your Authorized Challenge Dealer for replacements.
FOR PARTS AND SERVICE, contact the Authorized Challenge Dealer from whom you purchased
your machine. Use the illustrations and parts lists at the back of this manual to identify the correct
parts needed. Always give the SERIAL NUMBER and MODEL of your machine to insure the correct
parts are sent as soon as possible.
RECORD YOUR MACHINE SERIAL NUMBER in the space provided on the front cover of this
manual. Also fill out the warranty card accompanying this manual and return it DIRECTLY TO
CHALLENGE.
If you bought a used machine, it is important to have the following information on record at Challenge.
Copy this page, fill in the information and send it care of The Challenge Service Department, 6125
Norton Center Drive •Norton Shores •MI 49441-6081.
CHALLENGE MODEL SERIAL NUMBER
ATTN COMPANY
ADDRESS
CITY STATE/PROVINCE ZIP
PHONE DATE INSTALLED
DEALER NAME & CITY
* WARRANTY INFORMATION *
PLEASE REVIEW THE ENCLOSED WARRANTY INFORMATION SHEET
It is very important that you read and understand the conditions outlined in the Warranty Information
Sheet attached to the outside of the shipping container of your machine.
The Warranty Information Sheet must be filled out completely and returned to THE CHALLENGE
MACHINERY COMPANY in order for the warranty to be issued for this machine.
Challenge® is a registered trademark of
The Challenge Machinery Company •6125 Norton Center Drive •Norton Shores, MI 49441-6081
Copyright© 2009 by The Challenge Machinery Company. All rights reserved. Printed in the USA.
1.0 Introduction
3
TABLE OF CONTENTS
1.0 Introduction ...................................................................................................................................... 2
2.0 Safety............................................................................................................................................... 4
2.1 Precautions.................................................................................................................................. 4
2.2 Power Lockout Procedure ........................................................................................................... 4
2.3 Warning Label Definitions............................................................................................................ 5
3.0 Packing List...................................................................................................................................... 6
4.0 Specifications................................................................................................................................... 8
5.0 Accessories...................................................................................................................................... 9
6.0 Installation Guide ........................................................................................................................... 10
6.1 Inspecting Shipment.................................................................................................................. 10
6.2 Unpacking.................................................................................................................................. 10
6.3 Leveling ..................................................................................................................................... 10
6.4 Cleaning..................................................................................................................................... 10
6.5 Power Hook-up (SCM only)....................................................................................................... 10
6.6 Knife and Die Installation........................................................................................................... 10
7.0 User’s Guide .................................................................................................................................. 11
7.1 SCM/MSCM Diagrams .............................................................................................................. 11
7.2 SCM Operation.......................................................................................................................... 13
7.3 MSCM Operation (Manual Machine)......................................................................................... 13
7.4 Side and Back Gauge Adjustment............................................................................................. 13
7.5 Knife and Die Change................................................................................................................ 14
7.6 Straight Diagonal Cutting........................................................................................................... 16
7.7 Lubrication................................................................................................................................. 16
7.8 Operating Tips........................................................................................................................... 17
8.0 Appendix A - Maintenance Guide.................................................................................................. 18
8.1 Mechanical System.................................................................................................................... 19
8.1.1 Knife Return Springs.......................................................................................................... 19
8.1.2 Dovetail Gib........................................................................................................................ 19
8.1.3 Hydraulic System (SCM only) ............................................................................................ 20
8.1.4 Hydraulic Fluid Check ........................................................................................................ 20
8.1.5 Replacing Hydraulic Fluid................................................................................................... 21
8.1.6 Hydraulic Fluid Compatibility List ....................................................................................... 22
8.2 Electrical System (SCM only).................................................................................................... 22
8.2.1 Fuse Check and Replacement........................................................................................... 22
9.0 Appendix B–Parts List.................................................................................................................... 23
9.1 Mechanical................................................................................................................................. 23
9.1.1 A-8300-2 Main Assembly- Knife Head............................................................................. 23
9.1.2 A-8300-2 Main Assembly- Knife Head (Rear).................................................................. 25
9.1.3 A-8300-2 Main Assembly- Underside .............................................................................. 27
9.1.4 A-8300-2 Main Assembly- Hood...................................................................................... 29
9.1.5 A-8300-2 Main Assembly- Base....................................................................................... 31
9.1.6 A-8300-2 Main Assembly- MSCM.................................................................................... 33
9.1.7 83001 Hydraulic Power Unit Assembly- SCM, Rev. B..................................................... 35
9.2 Electrical .................................................................................................................................... 36
9.2.1 E-3042 Basic Machine Schematic ................................................................................... 36
9.2.2 E-3042 Interconnection Diagram ..................................................................................... 37
10.0 Appendix C- Troubleshooting ...................................................................................................... 38
2.0 Safety
4
2.0 Safety
2.1 Precautions
•By nature of the functions the cornering machine performs, it has some inherent dangers
associated with its use. Read and thoroughly understand the safety precautions outlined below.
•This machine is designed for one-person operation. Never operate the machine with more than
one person.
•Cut/crush hazard. Keep hands from under the knife and plunger while in operation.
•Do not operate with any covers removed.
•Safe use of this machine is the responsibility of the operator. Use good judgment and common
sense when working with and around this machine.
•Read and understand all instructions thoroughly before using the machine. If questions remain,
contact your Authorized Challenge Dealer. Failure to understand the operating instructions may
result in personal injury.
•Only trained and authorized individuals should operate this machine.
•Disconnect power before performing maintenance. See Section 2.2 , Power Lockout Procedure.
•Observe all caution labels on this machine.
•When replacing hydraulic parts, loosen the connections slowly to relieve pressure. Never loosen
connections while the machine is running. Allow hydraulic fluid to cool before performing
maintenance on the hydraulic system.
•Never leave the machine unattended while running.
•If the machine operates abnormally, consult Appendix C- Troubleshooting.
2.2 Power Lockout Procedure
For maximum safety while making adjustments or repairs to your machine, be sure to disconnect
power from the machine. Disconnect the power plug from its socket.
Figure 1 – Main Power Disconnect
2.0 Safety
5
2.3 Warning Label Definitions
The following warning label is found on the front cover of the machine. Read and understand the
meaning of this symbol. If this label is lost from the machine, it should be replaced.
SINGLE PERSON OPERATION
Do not operate with more than one person.
CUT/CRUSH HAZARD
Keep hands from under plunger and knife while in operation.
CRUSH HAZARD
Do not operate with any covers removed.
SHOCK HAZARD
Disconnect power before removing cover. Replace covers before operation.
3.0 Packing List
6
3.0 Packing List
SCM Single Cornering Machine MSCM Single Cornering Machine
Part No. Description Qty.
CMC-431A Single Cornering Machine 1
or
CMC-431M Manual Single Cornering Machine 1
Each machine includes the following tool kit items.
8315 Knife Hold-Down Block 1
6751 Holder- Plunger 1
6751-1 Clamp Holder- MSCM (MSCM only) 1
W-171 1/8” hex wrench- long arm 1
W-172 3/16” hex T-wrench (extra long) 1
83014 Jogging Aid 1
W-130 3/16” hex wrench 1
6629 Gib Lube 1
W-105 ¼” hex wrench 1
W-131 5/16 hex wrench 1
3.0 Packing List
7
4.0 Specifications
8
4.0 Specifications
Description
US Units
Metric Units
Maximum Pile Height 4” 10 cm
Table Depth 24” 61 cm
Table Width 20” 51 cm
Table Height 35” 89 cm
Overall Height 51” 130 cm
Footprint 20 X 24” 51 X 61 cm
Net Weight (SCM)
Shipping Weight (SCM)
Net Weight (MSCM)
Shipping Weight (MSCM)
Electrical (SCM only)
½ HP
115 V/ 15 A
1 PH
60/50 Hz
20 A service size
Otros manuales para SCM
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipos industriales de Challenge
