CH Hanson Norse 9683124 Instrucciones de uso

Operating Instructions & Parts Manual

9643312.01 0318

Model 9683124

10˝

Bench Top

Band Saw

9683124_oipm_En011_9643312.01 03/21/18 Page 1

GE ING S AR ED

SAFE Y / SPECIFICA IONS

ASSEMBLY / INS ALLA ION

OPERA ION

ROUBLESHOO ING

MAIN ENANCE / REPAIR

NOR E Operating Manual & Parts List 9683124

Please read and save hese ins ruc ions. Read carefully before a emp ing o assemble, ins all,

opera e or main ain he produc described.

Pro ec yourself and o hers by observing all safe y informa ion. Failure o comply wi h ins ruc ions

could resul in personal injury and/or proper y damage! re ain ins ruc ions for fu ure reference.

Model #: ________________________

Serial #: _________________________

Purchase Da e: ___________________

9683124_oipm_En011_9643312.01 03/21/18 Page 2

GETTI G STARTED

Structural Requirements

Make sure all supporting structures and load attaching devices are

strong enough to hold your intended loads. If in doubt, consult a

qualified structural engineer.

Electrical Requirements

The power supply to the Band Saw needs to be 120 volt/ 3.4 amp,

single phase, 60 z. The standard allowable voltage variation is

plus or minus 10%.

Tools eeded:

Standard mechanic’s hand tool set.

U PACKI G

Be carefu not to touch overhead power

ines, piping, ighting, etc. if ifting

equipment is used. Band Saw weighs approximate y 77 bs,

proper too s, equipment and qua iﬁed personne shou d be

emp oyed in a phases of unpacking and insta ation.

Carton should be handled with care to avoid damage from

dropping, bumping, etc. Store and unpack carton with correct side

up. After unpacking Band Saw, inspect carefully for any damage

that may have occurred during transit. Check for loose, missing or

damaged parts. If any damage or loss has occurred, claim must be

filed with carrier immediately. Check for completeness. Immediately

report missing parts to dealer.

Band Saw is shipped partially assembled. End user will need to

assemble loose parts to machine.

IMPOR AN : The tool has been coated with a protective coating.

In order to ensure proper fit and operation, the coating must be

removed. Remove coating with mild solvents such as mineral

spirits and a soft cloth. Nonflammable solvents are recommended.

After cleaning, cover all exposed metal surfaces with a light coating

of oil.Paste wax is recommended for table top.

Never use high y vo ati e so vents. Avoid

getting c eaning so ution on paint as it

may tend to deteriorate these ﬁnishes. Use soap and water

on painted components.

Contents:

• Band Saw (1)

• Table (1)

• Guide rail (1)

• Rip fence with knob (1)

• Miter gauge assembly (1)

• Pushstick (1)

• ardware bag (1) - Includes: M6 x 30 hex head bolt and nut;

four each hex bolts and M6 serrated washers; four each wing

nut bolts and washers.

• Operating Instructions and Parts Manual (1)

Unpack:

Do not discard packing materials until after machine has been

inspected for damage and completeness. Locate loose parts and

set aside.

Inspect:

After unpacking the unit, carefully inspect for any damage that may

have occurred during transit. Check for loose, missing or damaged

parts. Shipping damage claims must be filed with the carrier.

All tools should be visually inspected before use, in addition to

regular periodic maintenance inspections.

Be sure that the voltage labeled on the unit matches your power

supply.

SAFETY RULES

For your own safety, read a of the

instructions and precautions before

operating too .

PROPOSI ION 65 WARNING: Some dust created by

using power tools contain chemicals known to the state

of California to cause cancer, birth defects or other

reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other masonry

products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area and work with approved safety

equipment. Always wear OSHA/NIOSH approved, properly fitting

face mask or respirator when using such tools.

A ways fo ow proper operating

procedures as deﬁned in this manua even

if you are fami iar with the use of this or simi ar too s.

Remember that being care ess for even a fraction of a

second can resu t in severe persona injury.

Be Prepared for Job

• Wear proper apparel. Do not wear loose clothing, gloves,

neckties, rings, bracelets or other jewelry which may get

caught in moving parts of machine.

• Wear protective hair covering to contain long hair.

• Wear safety shoes with non-slip soles.

• Wear safety glasses complying with United States ANSI Z87.1.

Everyday glasses have only impact resistant lenses. They are

NO safety glasses.

NOR E Operating Manual & Parts List 9683124

GE ING S AR ED SAFE Y / SPECIFICA IONS ASSEMBLY / INS ALLA ION OPERA ION ROUBLESHOO ING MAIN ENANCE / REPAIR

9683124_oipm_En011_9643312.01 03/21/18 Page 3

SAFETY RULES (CO TI UED)

• Wear face mask or dust mask if operation is dusty.

• Be alert and think clearly. Never operate power tools when

tired, intoxicated or when taking medications that cause

drowsiness.

Prepare Work Area for Job

• Keep work area clean. Cluttered work areas invite accidents.

• Do not use power tools in dangerous environments. Do not

use power tools in damp or wet locations. Do not expose

power tools to rain.

• Work area should be properly lighted.

• Proper electrical receptacle should be available for tool. Three-

prong plug should be plugged directly into properly grounded,

three-prong receptacle.

• Extension cords should have a grounding prong and the three

wires of the extension cord should be of the correct gauge.

• Keep visitors at a safe distance from work area.

• Keep children out of workplace. Make workshop childproof.

Use padlocks, master switches or remove switch keys to

prevent any unintentional use of power tools.

Tool Should Be Maintained

• Always unplug tool prior to inspection.

• Consult manual for specific maintaining and adjusting

procedures.

• Keep tool lubricated and clean for safest operation.

• Remove adjusting tools. Form habit of checking to see that

adjusting tools are removed before switching machine on.

• Keep all parts in working order. Check to determine that the

guard or other parts will operate properly and perform their

intended function.

• Check for damaged parts. Check for alignment of moving

parts, binding, breakage, mounting and any other condition

that may affect a tool’s operation.

• A guard or other part that is damaged should be properly

repaired or replaced. Do not perform makeshift repairs. (Use

parts list provided to order repair parts.)

Know How to Use Tool

• Use right tool for job. Do not force tool or attachment to do a

job for which it was not designed.

• Disconnect tool when changing the blade.

• Avoid accidental start-up. Make sure that the tool is in the OFF

position before plugging in.

• Do not force tool. It will work most efficiently at the rate for

which it was designed.

• Keep hands away from moving parts and cutting surfaces.

• Never leave tool running unattended. Turn the power off and

do not leave tool until it comes to a complete stop.

• Do not overreach. Keep proper footing and balance.

• Never stand on tool. Serious injury could occur if tool is tipped

or if blade is unintentionally contacted.

• Know your tool. Learn the tool’s operation, application and

specific limitations.

• Use recommended accessories. Use of improper accessories

may cause risk of injury to persons.

• andle workpiece correctly. Protect hands from possible injury.

• Turn machine off if it jams. Blade jams when it digs too deeply

into workpiece. (Motor force keeps it stuck in the work.) Do not

remove jammed or cut off pieces until the saw is turned off,

unplugged and the blade has stopped.

• Maintain proper adjustment of blade tension, blade guides and

thrust bearings.

• Adjust upper guide to just clear workpiece.

• old workpiece firmly against table.

• DIRECTION OF FEED: Feed work into a blade or cutter

against the direction of rotation of the blade or cutter only.

The operation of any power too can

resu t in foreign objects being thrown into

the eyes, which can resu t in severe eye damage. A ways

wear safety gogg es comp ying with United States ANSI

Z87.1 before commencing power too operation.

Think safety! Safety is a combination of

operator common sense and a ertness at

a times when too is being used.

SPECIFICATIO S

The NORSE 10" Bench Top Band Saw features welded steel frame

construction and a solid cast iron table surface to insure durability. It

is designed for cutting hard and soft woods. The saw is equipped

with a miter gauge for performing many different operations. A

convenient quick tensioning and comprehensive tracking

mechanism makes blade changing quick and easy. Saw also

features a rip fence and dust collection port.

Depth of throat at 90° 91⁄2˝

Maximum depth of cut at 90° 4˝

Maximum depth of cut at 45° 2˝

Table size 131⁄4x 131⁄4˝

Table tilt 0° to 45°

Wheel diameter 10˝

Blade length 673⁄8˝

Blade width 1/4 - 1/2˝

Blade speed 2900 FPM

Motor 1/3 P, 120V, 3.4A, 60 z, 1720 RPM

Overall dimensions 21 x 161⁄2x 34˝

Weight 70 lbs

Shipping weight 77 lbs

Dust collection port 2, 21⁄2and 4˝

GE ING S AR ED

SAFE Y / SPECIFICA IONS

ASSEMBLY / INS ALLA ION

OPERA ION

ROUBLESHOO ING

MAIN ENANCE / REPAIR

NOR E Operating Manual & Parts List 9683124

9683124_oipm_En011_9643312.01 03/21/18 Page 4

ASSEMBLY

Refer to Figures 4, 5, 6 and 8.

Do not attempt assemb y if parts are

missing. Use this manua to order repair

parts.

The machine is supplied partly assembled. Prior to use, the

following items have to be installed: Table, Guide Rail, Rip Fence,

Dust Collector (not included) and Rip Fence.

To avoid injury, do not attempt to run or

use this machine unti a parts are

assemb ed and working proper y.

Assemble Table to Trunnion

Refer to Figure 1

Assemble the table on to the upper table trunnion, taking care

when passing the saw blade through the slot of the table.

1. Attach M6 x 30 hex head bolt and nut (Stop Bolt) into hole next

to the insert on table bottom.

2. Locate four hex bolts and four M6 serrated washers from the

bag of loose parts. Mount the table to the upper table trunnion

and install a bolt with washer in each hole, and then tighten

with adjustable wrench.

Centering the Table

Refer to Figure 1

1. Loosen the four hex bolts mounting the table to the upper table

trunnion.

2. Move the table sideways as required, until the saw blade runs

through the center of the table insert.

3. If moving the upper table trunnion is not enough to center the

table, loosen the four flange nuts holding the lower table

trunnion and move the table sideways to place the table in the

center.

4. Re-tighten hex bolts for trunnion and flange nuts, recheck the

saw blade position.

Setting Table Square to Saw Blade

Refer to Figures 2 and 3.

Loosen the knob on the lower table trunnion and place a suitably

sized square against the saw blade. If the table requires

adjustment, proceed as follows:

1. Using a wrench, release the hex nut on the bolt (see Figure 2).

Place the wrench on the hex bolt and adjust until the table is

square to the saw blade.

2. Tighten the hex nut and recheck the saw blade and the table

for squareness.

3. Lock the table into position and check that the indicator reads

zero degree on the side of lower table trunnion. Loosen the

screw securing the indicator and reset if necessary to give zero

degree reading (see Figure 3).

Fasten Guide Rail

Refer to Figure 4.

• Fasten the guide rail with four each wing nut bolts and washers

to the table.

NOR E Operating Manual & Parts List 9683124

GE ING S AR ED SAFE Y / SPECIFICA IONS ASSEMBLY / INS ALLA ION OPERA ION ROUBLESHOO ING MAIN ENANCE / REPAIR

Figure 1 - Assemble table to trunnion.

ex Bolts

Trunnion

Stop Bolt

Flange

Bolts

Figure 2 - Square table to saw blade.

Square

ex Bolt

ex Nut

Figure 3 - Set indicator to zero.

Figure 4 - Fasten guide rail.

9683124_oipm_En011_9643312.01 03/21/18 Page 5

ASSEMBLY (CO TI UED)

Install Rip Fence

Refer to Figure 5.

• Lay the rip fence onto the guide rail. Adjust the rip fence

parallel to the saw blade. Tighten rip fence handle by pressing

downward.

Stabilize Machine

Refer to Figure 6.

• To ensure sufficient upright stability of the machine it should be

bolted to floor, bench or worktable. For this purpose 8mm holes

are provided in the machine’s base. Mounting hardware not

provided.

Use Suitable Dust Collector

Refer to Figure 6 and 8.

• The band saw has a dust port included that will accommodate

2", 21⁄2" and 4" dust collection hoses.

It is recommended that when in use, the band saw is connected to

a suitable dust collector.

I STALLATIO

Electrical Connections

A e ectrica connections must be

performed by a qua iﬁed e ectrician.

Make sure unit is off and disconnected

from power source any time wiring is

inspected.

Power Source

Band Saw is prewired for 120 volt, 60 Z power source.

The motor is designed for operation on the voltage and frequency

specified. Normal loads will be handled safely on voltages not more

than 10% above or below the specified voltage.

Running the unit on voltages which are not within the range may

cause overheating and motor burn-out. eavy loads require that

the voltage at motor terminals be no less than the voltage specified.

Power supply to the motor is controlled by a single pole toggle

switch.

Grounding Instructions

Improper connection of equipment

grounding conductor can resu t in the risk

of e ectrica shock. Equipment shou d be grounded whi e in

use to protect operator from e ectrica shock.

• Check with a qualified electrician if grounding instructions are

not understood or if in doubt as to whether the tool is properly

grounded.

This tool is equipped with an approved 3-conductor cord rated at

150V and a three prong grounding type plug or your protection

against shock hazards.

• Grounding plug should be plugged directly into a properly

installed and grounded 3- prong grounding-type receptacle, as

shown (Figure 9).

GE ING S AR ED

SAFE Y / SPECIFICA IONS

ASSEMBLY / INS ALLA ION

OPERA ION

ROUBLESHOO ING

MAIN ENANCE / REPAIR

NOR E Operating Manual & Parts List 9683124

Figure 5 - Install rip fence.

Figure 6- Mounting holes and dust port.

Mounting

oles Dust Port

Figure 7 - Know your band saw.

Blade Tension Knob

Door Locking

Knob

Miter Gauge

Switch

Guide Rail

Figure 8 - Know your band saw.

Blade Tracking

Knob

Dust Port

Upper Trunnion

Lower Trunnion

Guide Post

Adjusting and

Lock Knob

9683124_oipm_En011_9643312.01 03/21/18 Page 6

I STALLATIO (CO TI UED)

• Do not remove or alter grounding prong in any

manner. In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electrical shock.

Do not permit ﬁngers to touch the

termina s of p ug when insta ing or

removing from out et.

• Plug must be plugged into matching outlet that is properly

installed and grounded in accordance with all local codes and

ordinances. Do not modify plug provided. If it will not fit in

outlet, have proper outlet installed by a qualified electrician.

• Inspect tool cords periodically, and if damaged, have repaired

by an authorized service facility.

• Green (or green and yellow) conductor in cord is the grounding

wire. If repair or replacement of the electric cord or plug is

necessary, do not connect the green (or green and yellow) wire

to a live terminal.

Where a 2-prong wall receptacle is encountered, it must be

replaced with a properly grounded 3-prong receptacle installed in

accordance with National Electric Code and local codes and

ordinances.

This work shou d be performed by a

qua iﬁed e ectrician.

A temporary 3-prong to 2-prong grounding adapter (see Figure 10)

is available for connecting plugs to a two pole outlet if it is properly

grounded.

• Do not use a 3-prong to 2-prong grounding adapter unless

permitted by local and national codes and ordinances. (A 3-

prong to 2-prong grounding adapter is not permitted in

Canada.) Where permitted, the rigid green tab or terminal on

the side of the adapter must be securely connected to a

permanent electrical ground such as a properly grounded

water pipe, a properly grounded outlet box or a properly

grounded wire system.

Many cover plate screws, water pipes and outlet boxes are not

properly grounded. To ensure proper ground, grounding means

must be tested by a qualified electrician.

Extension Cords

• The use of any extension cord will cause some drop in voltage

and loss of power.

• Wires of the extension cord must be of sufficient size to carry

the current and maintain adequate voltage.

• Use the table to determine the minimum wire size (A.W.G.)

extension cord.

• Use only 3-wire extension cords having 3-prong grounding

type plugs and 3-pole receptacles which accept the tool plug.

• If the extension cord is worn, cut, or damaged in any way,

replace it immediately.

Extension Cord Length and Gauge

Length A.W.G.

Up to 25 ft. 18

25 to 100 ft. 16

100 to 150 ft. 14

NOTE Using extension cords over 150 ft. long is not

recommended.

This machine must be grounded. To avoid

e ectrocution or ﬁre, any repairs to

e ectrica system shou d be done on y by a qua iﬁed

e ectrician, using genuine rep acement parts.

OPERATIO

Safety Precautions

A ways observe the fo owing safety

precautions.

• Whenever adjusting or replacing any parts on the band saw

turn, switch off and remove plug from power source.

• Make sure the blade guides are positioned correctly.

• Use the appropriate blade for the workpiece that is being cut.

• Use a sharp blade. Replace dull blades or blades which are

missing teeth.

• Make sure the blade is tensioned properly and going in the

right direction.

• Use the proper blade speed for the work.

• For optimum performance, do not stall the motor or reduce the

speed. Use the proper feed pressure.

• Secure the workpiece in a stable position.

• Check that all guards are attached.

• After turning the switch on, let the blade come to full speed.

• Keep hands away from the blade and all moving parts.

• Always wear eye protection or face shield.

• Always stop the band saw before removing scrap pieces from

table.

• Never attempt to saw stock that does not have a flat surface,

unless a suitable support is used.

NOR E Operating Manual & Parts List 9683124

GE ING S AR ED SAFE Y / SPECIFICA IONS ASSEMBLY / INS ALLA ION OPERA ION ROUBLESHOO ING MAIN ENANCE / REPAIR

Figure 9 – 3-Prong Receptacle

Properly Grounded Outlet

Grounding Prong

3-Prong Plug

Figure 10 – 2-Prong Receptacle With Adapter

Grounding Lug

Adapter

3-Prong Plug 2-Prong

Receptacle

Make sure this is

connected to a known

grounded receptacle.

9683124_oipm_En011_9643312.01 03/21/18 Page 7

OPERATIO (CO TI UED)

• Always hold material firmly and feed it into the blade at a

moderate speed.

• Always turn off the machine if the material is to be backed out

of an uncompleted cut.

• Make sure that the blade tension and blade tracking are

properly adjusted.

• Make “relief” cuts before cutting long curves.

• Release blade tension when the saw will not be used for a long

period of time.

O /OFF Switch

Refer to Figure 11.

Before starting check if any part of your

band saw is missing, ma functioning, has

been damaged or broken, such as the motor switch, or other

operation contro , a safety device or the power cord, turn

the band saw off and unp ug it unti the particu ar part is

proper y repaired or rep aced.

The ON/OFF switch is located on the left front of the saw column.

To turn saw ON, pull the switch to the up position. To turn saw OFF,

push the switch to the down position.

The saw can be locked from unauthorized use by locking the

switch. To lock the switch:

1. Turn the switch to OFF position and disconnect saw from

power source.

2. Pull the key out. The switch cannot be turned on with the key

removed.

NOTE: Should the key be removed from the switch at the ON

position, the switch can be turned off but cannot be turned on

again.

• To replace key, slide key into the slot on switch until it snaps.

Adjustments

The blade tracking, tension and blade guides have been properly

adjusted at the factory. owever, the adjustments may change

while the saw is in transit.

It is recommended to verify these adjustments before operating

saw.

Changing and Adjusting the Saw Blade

This band saw is factory-equipped with a general-purpose wood

cutting blade; the saw blade is set prior to delivery.

To change the saw blade, the following procedure must be

followed:

To avoid injury from unexpected starting,

whenever changing the saw b ade or

carrying out adjustments, switch the band saw off and

remove the power cord from the main out et. To avoid injury

to hands when hand ing the saw b ade, wear g oves

whenever necessary.

1. Remove the rip fence, the guide rail, the wing nut and screw

from the table.

2. Open the upper and lower doors by turning the door locking

knobs.

3. Loosen the tracking lock knob (See figure 13, page 9).

4. Loosen the blade tension by turning the blade tension knob on

the top of the upper wheel housing counterclockwise until the

saw blade has slackened (viewed from above). See Figure 12.

5. Remove the saw blade from the upper and lower wheels.

When fitting the new saw blade ensure the blade teeth are pointing

downwards and towards you at the position where the saw blade

passes through the table.

6. Re-tension the new saw blade and check the saw blade

tracking by turning the upper wheel by hand.

The saw blade should run in the center of the band saw wheels. If

needed adjust the tracking of the saw blade, follow procedures for

"Tracking the Saw Blade".

7. Tighten the tracking lock knob.

8. Replace the rip fence, the guide rail, the wing nut and screw to

the table.

9. Close the upper and lower doors by turning the door locking

knobs before reconnecting the power supply.

GE ING S AR ED

SAFE Y / SPECIFICA IONS

ASSEMBLY / INS ALLA ION

OPERA ION

ROUBLESHOO ING

MAIN ENANCE / REPAIR

NOR E Operating Manual & Parts List 9683124

Figure 11 - O /OFF Switch and Key

Figure 12 - Blade Tension Knob

9683124_oipm_En011_9643312.01 03/21/18 Page 8

OPERATIO (CO TI UED)

Tracking the Saw Blade

Refer to Figure 13.

Set the tracking of the saw blade before setting the blade guides.

1. Once the saw blade is installed and tensioned, track the saw

blade by adjusting the tracking knob by hand.

2. The saw blade should run in the center of the band saw

wheels.

3. When the correct adjustment is achieved lock the tracking

knob with the tracking lock knob.

Setting the Cutting Height

Refer to Figure 13.

The upper blade guide should be set as close as practical against

the workpiece.

1. To adjust this height, loosen the guide post lock knob at the

side of the upper wheel housing.

2. Set the blade guide to the required height by turning the guide

post adjusting knob.

3. Tighten guide post locking knob after setting.

Aligning the Upper Blade Guide

The upper blade guide consists of:

• A thrust bearing (supporting the band saw blade from the rear).

• Two guide bearings (providing lateral support).

All bearings need to be readjusted after every band saw blade

change and/or tracking adjustment.

NOTE: Periodically check all bearings for wear, if necessary

replace both guide bearings at the same time.

Adjusting the Thrust Bearing

Refer to Figure 14.

1. If necessary, align and tighten the band saw blade.

2. Loosen fixing screw of the upper blade guide.

3. Align upper blade guide

4. Tighten the upper blade guide's fixing screw.

5. Loosen the thrust bearing's lock screw.

6. Adjust thrust bearing position (distance thrust bearing - band

saw blade = 0.5 mm – if the band saw blade is turned by hand,

it must not touch the thrust bearing).

7. Tighten the thrust bearing lock screw.

Adjusting the Guide Bearings

Refer to Figure 15.

1. Loosen knurled nut.

2. Set guide bearings with the knurled thumb screws against the

band saw blade.

3. Turn band saw wheel by hand in a clockwise direction several

times to bring the guide bearings in correct position – both

guide bearings should just touch the band saw blade.

4. Retigthen knurled nut to lock the knurled thumb screw.

Aligning the Lower Blade Guide

The lower blade guide consists of:

• A thrust bearing (supporting the band saw blade from the rear).

• Two guide bearings (providing lateral support).

These parts need to be readjusted after every band saw blade

change or tracking adjustment:

NOTE: Periodically check thrust bearings and guide bearings for

wear, if necessary replace both guide bearings at the same time.

NOR E Operating Manual & Parts List 9683124

GE ING S AR ED SAFE Y / SPECIFICA IONS ASSEMBLY / INS ALLA ION OPERA ION ROUBLESHOO ING MAIN ENANCE / REPAIR

Figure 13 - Set tracking of saw blade.

Tracking

Lock Knob

Tracking

Knob

Guide Post

Lock Knob

Guide Post

Adjusting

Knob

Figure 14 - Adjusting the trust bearings.

Lock

Screw

Fixing

Screw

Thrust

Bearing

Figure 15 - Adjusting the guide bearings.

Knurled

Thumb

Screw

Knurled

Thumb Screw

Guide

Bearings

9683124_oipm_En011_9643312.01 03/21/18 Page 9

OPERATIO (CO TI UED)

Basic Alignment

Refer to Figures 16 and 18.

1 Open the lower housing door.

2. Loosen lower blade guide fixing-screw with an open jaw

wrench.

3. Adjust position of lower blade guide until band saw blade is

centered between the guide bearings.

4. Tighten fixing-screw.

Adjusting the Thrust Bearing

Refer to Figure 17.

1. Loosen the thrust bearing's lock screw.

2. Adjust thrust bearing position (A) (distance thrust bearing -

band saw blade = 0.5 mm – if the band saw blade is turned by

hand, it must not touch the thrust bearing).

3. Tighten the thrust bearing lock screw.

Adjusting the Guide Bearings

Refer to Figure 19.

1. Loosen screws (B).

2. Set guide bearings against the band saw blade.

3. Turn the band saw wheel by hand in a clockwise direction

several times to bring the guide bearings in correct position –

both guide bearings should just touch the band saw blade.

4. Tighten screws (B) again.

5. Close the lower housing door.

Tilting the Table

For bevel cuts, the table tilts 0 through 45 degrees.

1. To tilt the table, loosen the handle on the table trunnion, set the

table to the required angle and tighten the handle again (see

Figure 19).

2. It is recommended to verify the correct angle setting using an

angle guide, or by making trial cuts in scrap wood. Adjust the

indicator accordingly by using a Phillips head screwdriver.

Adjusting the Rip Fence

Refer to Figure 20.

The locking pressure of the rip fence has been factory set; if

adjustment is required proceed as follows:

1. Raise the fence handle to horizontal position.

2. Turn the fence handle clockwise to increase clamping

pressure, counterclockwise to decrease clamping pressure.

3. After turning the fence handle counterclockwise, slide the rip

fence to the desired position on the guide rail.

4. The fence handle has a cam action, press down the handle to

clamp tightly to the table after setting rip fence to desired

position.

GE ING S AR ED

SAFE Y / SPECIFICA IONS

ASSEMBLY / INS ALLA ION

OPERA ION

ROUBLESHOO ING

MAIN ENANCE / REPAIR

NOR E Operating Manual & Parts List 9683124

Figure 19 - Tilting the table.

andle

Figure 20 - Adjusting the rip fence.

Figure 17 - Basic alignment.

Fixing

Screw

Figure 17 - Basic alignment.

Thrust Bearing

Lock Screw

Figure 18 - Basic alignment.

Guide

Bearings

9683124_oipm_En011_9643312.01 03/21/18 Page 10

Tabla de contenidos

Otros manuales de Sierra de CH Hanson

CH Hanson

CH Hanson PALMGREEN 9683336 Instrucciones de uso

CH Hanson

CH Hanson NORSE 9683113 Manual de usuario

CH Hanson

CH Hanson Palmgren 9683337 Instrucciones de uso

CH Hanson

CH Hanson Norse 9683125 Manual de usuario

CH Hanson

CH Hanson NORSE 9683412 Instrucciones de uso

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario