GETTING STARTED
Structural Requirements
Make sure all supporting structures and load attaching devices are
strong enough to hold your intended loads. f in doubt, consult a
qualified structural engineer.
Electrical Requirements
The power supply to the Sander needs to be 120 volt/ 3.5 amp,
single phase, 60 Hz. The standard allowable voltage variation is
plus or minus 10%.
Tools Needed:
Standard mechanic’s hand tool set.
UN ACKING
Be careful not to touch overhead power
l nes, p p ng, l ght ng, etc. f l ft ng
equ pment s used. Sander we ghs approx mately 32 lbs,
proper tools, equ pment and qual fied personnel should be
employed n all phases of unpack ng and nstallat on.
Carton should be handled with care to avoid damage from
dropping, bumping, etc. Store and unpack carton with correct side
up. After unpacking Sander, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing or
damaged parts. f any damage or loss has occurred, claim must be
filed with carrier immediately. Check for completeness. mmediately
report missing parts to dealer.
Sander is shipped partially assembled. End user will need to
assemble loose parts to machine.
IMPOR AN : The tool has been coated with a protective coating.
n order to ensure proper fit and operation, the coating must be
removed. Remove coating with mild solvents such as mineral
spirits and a soft cloth. Nonflammable solvents are recommended.
After cleaning, cover all exposed metal surfaces with a light coating
of oil.
Never use h ghly volat le solvents. Avo d
gett ng clean ng solut on on pa nt as t
may tend to deter orate these fin shes. Use soap and water
on pa nted components.
Contents:
• 2 x 6" Belt and Disc Sander (1)
• Disc table (1)
• Abrasive disc (1)
• Mater gauge assembly (1)
• Belt table (1)
• Parts bag (1) includes: work stop; two knobs; one 10-1.5 x
16mm socket head bolt; one 10mm flat washer; two 6mm
washers; one each 5, 6 and 8mm hex wrenches and one
12mm open end wrench.
• Operating nstructions and Parts Manual (1)
Unpack:
• Do not discard packing materials until after machine has been
inspected for damage and completeness. Locate loose parts
and set aside.
Inspect:
• After unpacking the unit, carefully inspect for any damage that
may have occurred during transit. Check for loose, missing or
damaged parts. Shipping damage claims must be filed with the
carrier.
• All tools should be visually inspected before use, in addition to
regular periodic maintenance inspections.
• Be sure that the voltage labeled on the unit matches your
power supply.
SAFETY RULES
For your own safety, read all of the
nstruct ons and precaut ons before
operat ng tool.
PROPOSI ION 65 WARNING: Some dust created by
using power tools contain chemicals known to the state
of California to cause cancer, birth defects or other
reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry
products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area and work with approved safety
equipment. Always wear OSHA/NIOSH approved, properly fitting
face mask or respirator when using such tools.
Always follow proper operat ng
procedures as defined n th s manual even
f you are fam l ar w th the use of th s or s m lar tools.
Remember that be ng careless for even a fract on of a
second can result n severe personal njury.
Be repared for Job
• Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of machine.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States ANS Z87.1.
Everyday glasses have only impact resistant lenses. They are
NO safety glasses.
3
NOR E Operating Manual & Parts List 9681119
GE ING S AR ED SAFE Y / SPECIFICA IONS ASSEMBLY / INS ALLA ION OPERA ION ROUBLESHOO ING MAIN ENANCE / REPAIR
