Certa CTJCKHMDEMA Manual de usuario

Table of Contents

Accessories............................................................................................................................................1

Safety Warnings..................................................................................................................................1

Work Area........................................................................................................................................2

Electrical Safety.............................................................................................................................2

Personal Safety..............................................................................................................................2

Power Tool Use and Care..........................................................................................................3

Service...............................................................................................................................................3

Ha er Safety Warnings.........................................................................................................3

Usage......................................................................................................................................................4

Changing Tools...................................................................................................................................4

Mounting...........................................................................................................................................4

Dis ounting....................................................................................................................................4

Lubrication / Oil Level.....................................................................................................................4

Carbon Brushes..................................................................................................................................5

Maintenance.........................................................................................................................................5

Disposal..................................................................................................................................................5

Accessories

1 x Secondary Handle

1 x Pot of Lubricant

Safety Warnings

Wearing of protective goggles, hearing protection, safety shoes

and respiratory protection is strongly advised at all ti es!

•WARNING! Read all safety warnings and all instructions! Failure to follow the warnings

and instructions ay result in electric shock, fire and/or serious injury.

•Save all warnings and instructions for future reference.

•The ter “power tool” in the warnings refers to your ains-operated (corded) power

tool or battery operated (cordless) power tool.

•Avoid wearing jewellery or loose fitting clothing during use. Tie all long hair up into a

pony-tail before use.

•Unplug your tool fro the ains when you are not using it, when changing the bit or

perfor ing aintenance.

•Work in a clean and uncluttered workspace. You work area should also be well lit.

•Store the tool in a dry, cool location. Do not operate the tool near explosive or fla able

aterials.

•Work with tools in good condition that are designed for the task. This is a DIY tool, and

should be treated as such. Do not overload the unit. The tool should always be used with

it's additional handle and held fir ly with both hands.

•Before each use, check the oil level, tightness of the screws etc...

•Make sure you are not driving the tool into live electrical wires or functioning gas/water

pipes. This ay lead to risk of electrocution or an explosion. Before drilling down into

unknown ground, call the local authorities to ensure that no i portant infrastructure is

located below the ground.

•Do not try to open or dis antle the tool to repair or adjust it yourself. There are no user

serviceable parts inside. Contact the Kogan.co custo er support tea for infor ation

regarding repairs.

Work Area

1. Keep the work area clean and well lit. Cluttered and dark areas invite

accidents.

2. Do not operate the power tools in explosive atmospheres such as in the

presence of flammable liquids gases or dust. Power tools create sparks

which ay ignite the dust or fu es.

3. Keep children and bystanders away while operating the power tool.

Distractions can cause you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Do not modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power tools.

Un odified plugs and atching outlets will reduce the risk of electric

shock.

2. Avoid body contact with earthed or grounded surfaces such as pipes

radiators ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

3. Do not expose the power tool to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord for carrying pulling or

unplugging the power tool. Keep cord away from heat oil sharp edges

or moving parts. Da aged or entangled cords increase the risk of electric

shock.

5. When operating a power tool outdoors use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location is unavoidable use a

residual current device (RCD) protected supply. Use of an RCD reduces

the risk of electrical shock.

Personal Safety

1. Stay alert watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs alcohol or medication. A o ent of

inattention while operating power tools ay result in serious personal

injury.

2. Use safety equipment. Always wear eye protection. Safety equip ent

such as dust asks, non-skid safety shoes, hard hats and hearing

protection will reduce personal injuries and negative after-effects.

3. Avoid accidental starting. Ensure the switch is in the off position before

plugging unit in to the power supply picking up or carrying the tool.

Carrying power tools with your finger on the switch or plugging in power

tools with the switch in the on position invites accidents.

4. Remove any adjusting keys or wrenches before turning the power tool

on. A wrench or key left attached to a rotating part of a power tool ay

result in personal injury.

5. Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in oving parts.

Power Tool Use and Care

•Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

•Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and

ust be repaired.

•Disconnect the plug from the power source before making any

adjustments changing accessories or storing power tools. Such

preventative safety easures reduce the risk of starting the power tool

accidentally.

•Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate

the power tool. Power tools are dangerous in the hands of untrained

users.

•Maintain power tools. Check for misalignment or binding of moving

parts breakage of parts and any other condition that may affect the

power tool operation. If da aged, have the power tool repaired before

use. Many accidents are caused by poorly aintained power tools.

•Keep cutting tools sharp and clean. Properly aintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

•Use the power tool accessories and tool bits in accordance with these

instructions and in the manner intended for this particular tool taking

into account the working conditions and the work to be performed. Use

of the power tool for operations different to those intended could result in

a hazardous situation.

Service

•Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure the safety of the power tool

is aintained.

Hammer Safety Warnings

•Wear ear protection. Exposure to noise can cause hearing loss.

•Use auxiliary handle(s) if supplied with the tool. Loss of control can

cause personal injury.

•Hold the power tool by the insulated gripping surfaces when performing

an operation where the cutting accessory may contact hidden wiring or

even the tool's own power cord. A cutting accessory contacting a 'live'

wire ay ake exposed etal parts of the power tool 'live', and could

give the operator an electric shock.

Usage

•This tool is designed to break up concrete and si ilar aterials, for re oval, the

installation of cables, tubes, pipes, drainage or other civil engineering purposes.

•Before plugging the unit in, ensure that the power voltage and frequency

corresponds with those indicated on the tool's rating plate; and that the ON/OFF

button does not stick.

•The tool is operated when the trigger is pressed, and will stop functioning when

the trigger is released. Always hold the tool fir ly with both hands, with handles

while operating.

•It is so eti es necessary to apply force on the point of the drill spindle so that

the percussion syste will operate, otherwise the protection device against an

off-load operation ay activate.

•Adopt a oderate workload. The use of too uch force alters the safety and

efficiency of the tool.

•It is reco ended that the tool power be supplied by a residual current device

with a rated residual current of 30 A or less.

Changing Tools

Unplug the tool fro the power supply. Only use drill spindles co patible with the tool.

Mounting

Clean the drill spindle before use, and lightly oil the special i print. Pull and turn the

lock 180° clockwise.

Insert the drill spindle into the hexagonal housing with the slot on the lock side.

Turn the lock 180° counter-clockwise.

Pull the drill spindle to check that it only has approxi ately 3c of ove ent available.

Dismounting

Pull and turn the lock 180° clockwise.

Slide the drill spindle out of the housing. Clean any excess lubricant fro the i print

with a rag if desired.

Turn the lock 180° counter-clockwise.

Lubrication / Oil Level

Before checking the oil, ensure the unit is disconnected fro the power supply.

The oil weir should provide up to 20 days use based on 3 hours of use per day, however

the oil should still be checked every day. When holding the tool vertical with the drive

spindle pointing downwards, check the gauge window. At the point when the oil level is

just about to be no longer visible, the oil reservoir should be filled.

1. Re ove the oil gauge with a spanner, ensuring you do not da age or lose the

gasket.

2. Fill the reservoir with type #40 oil ( otor oil).

3. Replace the gauge.

Carbon Brushes

Ensure the tool is unplugged fro the power supply and allow the tool to sit unused for

50 hours before checking the brushes.

Re ove the brush cover, re ove the carbon-holder cap then re ove the brush.

The carbon brush should be at least 5 long. In the case of excessive wearing or

excessive sparks, replace both brushes with carbon brushes of identical characteristics.

Maintenance

WARNING: For aintenance and cleaning, always re ove the plug fro the electric

power supply. Never use water or other liquids to clean electric parts. It is

reco ended that the tool power be supplied by a residual current device with a rated

residual current of 30 A or less.

Each day of use, check that all screws and nuts are securely fastened. Except for the

procedures explained in this anual, there is no specific aintenance required.

The cleaning of plastic co ponents should be done with a soft da p cloth with so e

ild soap. Never sub erge the unit into any liquids and do not use any alcohols, spirits

or abrasive detergents.

If replace ent of the supply cord is necessary, this has to be done by a Kogan service

technician or a qualified electrician to avoid a safety hazard.

Contact the Kogan custo er support tea for further infor ation.

https://www.kogan.co /au/contact-us/ or 1300 304 292

Disposal

Waste electrical products should not be disposed of with your

household waste. Please recycle where adequate facilities

exist. Check with your local authorities for recycling advice.

Tabla de contenidos

Manuales populares de Martillo pilón de otras marcas

Kraissmann

Kraissmann 2000 AH 45 Manual de usuario

Sumake

Sumake ST-2212/R Manual de usuario

Makita

Makita HM1214C Manual de usuario

Sumake

Sumake ST-2231/R Manual de usuario

Stanley

Stanley STHM10 Manual de usuario

RODCRAFT

RODCRAFT RC5030 Manual de usuario

Villager

Villager VLN 1315 Manual de usuario

Hitachi

Hitachi H 65SC Manual del operador

Hitachi

Hitachi H 65SB2 Manual de usuario

socomec

socomec MDO 6000 TS Manual de lista de piezas

Hitachi

Hitachi H 45MR Manual

Atlas Copco

Atlas Copco PB 6S Guía de configuración

Pattfield Ergo Tools

Pattfield Ergo Tools PA-1700SH Manual de usuario

Coleman

Coleman Powermate 024-0075SP Manual de usuario

Makita

Makita HR3210C Guía de inicio rápido

WilTec

WilTec JH95A Manual de usuario

Master

Master MH 10-SE Manual de usuario

Stark

Stark RH 1300 DB Manual de usuario